Add NSH configuration
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@3072 42af7a65-404d-4744-a932-0658087f49c3
This commit is contained in:
patacongo
parent
8d312d5e81
commit
f47f9734cb
@ -20,6 +20,7 @@ Contents
|
||||
- Entering the ISP
|
||||
- BatchISP
|
||||
* Reset
|
||||
* Make Tip
|
||||
* AVR32DEV1 Configuration Options
|
||||
* Configurations
|
||||
|
||||
@ -229,11 +230,11 @@ AVR32 Bootloader
|
||||
verify, read) are performed using these buffers."
|
||||
|
||||
The following BatchISP command line will erase FLASH, write the nuttx binary
|
||||
into FLASH, and reset the AVR32. This command line is availabel in the
|
||||
into FLASH, and reset the AVR32. This command line is available in the
|
||||
script config/avr32dev1/tools/doisp.sh:
|
||||
|
||||
batchisp -device at32uc3b0256 -hardware usb -operation erase f memory flash \
|
||||
blankcheck loadbuffer nuttx program verify start reset 0
|
||||
blankcheck loadbuffer nuttx.elf program verify start reset 0
|
||||
|
||||
"BatchISP main commands available on AT32UC3xxxxx are:
|
||||
|
||||
@ -289,10 +290,23 @@ AVR32 Bootloader
|
||||
Reset
|
||||
^^^^^
|
||||
|
||||
The AVR32DEV1 reset button is not useful for restarting the program. It
|
||||
seems that, after the reset, the RTC is left is a bad state and is constantly
|
||||
busy (this might be the fault of the bootloader???). There does not seem
|
||||
to be any way around this except for power cycling the board.
|
||||
I don't trust the reset button -- if you reset and something weird happens,
|
||||
try a full power cycle.
|
||||
|
||||
Make Tip
|
||||
^^^^^^^^
|
||||
|
||||
Because this build uses a native Windows toolchain and the native Windows
|
||||
does not understand Cygwin/POSIX paths, the NuttX make sysem does something
|
||||
weird: It copies the configuration directories instead of simply linking
|
||||
to them (it could, perhaps, use the NTFS mklink command, but it doesn't).
|
||||
|
||||
A consequence of this is that you can easily get confused and get editting
|
||||
a file in one of the linked directories, re-build, and not see your changes.
|
||||
To work around this annoying behavior, I also do the following when I make:
|
||||
|
||||
make clean_context all <-- Remove and re-copy all of the directories, then make all
|
||||
doisp.sh <-- Load the code onto the board.
|
||||
|
||||
AVR32DEV1 Configuration Options
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
@ -410,6 +424,10 @@ sudirectory and can be selected as follow:
|
||||
|
||||
Where <subdir> is one of the following:
|
||||
|
||||
nsh:
|
||||
Configures the NuttShell (nsh) located at examples/nsh. The
|
||||
Configuration enables only the serial NSH interface.
|
||||
|
||||
ostest:
|
||||
This configuration directory, performs a simple OS test using
|
||||
examples/ostest.
|
||||
|
||||
145
configs/avr32dev1/nsh/Make.defs
Executable file
145
configs/avr32dev1/nsh/Make.defs
Executable file
@ -0,0 +1,145 @@
|
||||
############################################################################
|
||||
# configs/avr32dev1/nsh/Make.defs
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_AVR32_AVRTOOLSW),y)
|
||||
# AVR Tools under Windows
|
||||
CROSSDEV = avr32-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mpart=uc3b0256
|
||||
endif
|
||||
ifeq ($(CONFIG_AVR32_AVRTOOLSL),y)
|
||||
# AVR Tools under Linux
|
||||
CROSSDEV = avr32-
|
||||
ARCHCPUFLAGS = -mpart=uc3b0256
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/ld.script}"
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/ld.script
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = -Os -ffunction-sections -fdata-sections -fno-strict-aliasing
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin -muse-rodata-section
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHNOPICFLAGS = -fno-pic
|
||||
ARCHPICFLAGS = -fpic
|
||||
ARCHALLCFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) -pipe
|
||||
ARCHALLCXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) -pipe
|
||||
|
||||
CFLAGS = $(ARCHNOPICFLAGS) $(ARCHALLCFLAGS)
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(ARCHALLCFLAGS)
|
||||
CXXFLAGS = $(ARCHNOPICFLAGS) $(ARCHALLCXXFLAGS)
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(ARCHALLCXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES)
|
||||
AFLAGS = $(ARCHALLCFLAGS) -D__ASSEMBLY__
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
||||
795
configs/avr32dev1/nsh/defconfig
Executable file
795
configs/avr32dev1/nsh/defconfig
Executable file
@ -0,0 +1,795 @@
|
||||
############################################################################
|
||||
# configs/avr32dev1/nsh/defconfig
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_NOINTC - define if the architecture does not
|
||||
# support an interrupt controller or otherwise cannot support
|
||||
# APIs like up_enable_irq() and up_disable_irq().
|
||||
# CONFIG_ARCH_IRQPRIO - Define if MCU supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibrate
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
# CONFIG_ARCH_DMA - Support DMA initialization
|
||||
#
|
||||
CONFIG_ARCH=avr
|
||||
CONFIG_ARCH_AVR=y
|
||||
CONFIG_ARCH_AVR32=y
|
||||
CONFIG_ARCH_CHIP=at32uc3
|
||||
CONFIG_ARCH_CHIP_AT32UC3B0256=y
|
||||
CONFIG_ENDIAN_BIG=y
|
||||
CONFIG_ARCH_BOARD=avr32dev1
|
||||
CONFIG_ARCH_BOARD_AVR32DEV1=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=1140
|
||||
CONFIG_DRAM_SIZE=(32*1024)
|
||||
CONFIG_DRAM_START=0x00000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_NOINTC=y
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_BOOTLOADER=n
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_BUTTONS=y
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
CONFIG_ARCH_DMA=n
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
|
||||
CONFIG_AVR32_AVRTOOLSW=y
|
||||
CONFIG_AVR32_AVRTOOLSL=n
|
||||
|
||||
#
|
||||
# Individual subsystems can be enabled:
|
||||
#
|
||||
# CONFIG_AVR32_GPIOIRQ - GPIO interrupt support
|
||||
# CONFIG_AVR32_GPIOIRQSETA - Set of GPIOs on PORTA that support interrupts
|
||||
# CONFIG_AVR32_GPIOIRQSETB - Set of GPIOs on PORTB that support interrupts
|
||||
#
|
||||
# CONFIG_AVR32_USARTn - Enable support for USARTn
|
||||
# CONFIG_AVR32_USARTn_RS232 - Configure USARTn as an RS232 interface.
|
||||
# CONFIG_AVR32_USARTn_SPI - Configure USARTn as an SPI interface.
|
||||
# CONFIG_AVR32_USARTn_RS485 - Configure USARTn as an RS485 interface.
|
||||
# CONFIG_AVR32_USARTn_MAN - Configure USARTn as an Manchester interface.
|
||||
# CONFIG_AVR32_USARTn_MODEM - Configure USARTn as an Modem interface.
|
||||
# CONFIG_AVR32_USARTn_IRDA - Configure USARTn as an IRDA interface.
|
||||
# CONFIG_AVR32_USARTn_ISO786 - Configure USARTn as an ISO786 interface.
|
||||
#
|
||||
|
||||
CONFIG_AVR32_GPIOIRQ=y
|
||||
CONFIG_AVR32_GPIOIRQSETA=0
|
||||
CONFIG_AVR32_GPIOIRQSETB=0x0000000c
|
||||
|
||||
CONFIG_AVR32_USART0=n
|
||||
CONFIG_AVR32_USART0_RS232=n
|
||||
CONFIG_AVR32_USART0_SPI=n
|
||||
CONFIG_AVR32_USART0_RS485=n
|
||||
CONFIG_AVR32_USART0_MAN=n
|
||||
CONFIG_AVR32_USART0_MODEM=n
|
||||
CONFIG_AVR32_USART0_IRDA=n
|
||||
CONFIG_AVR32_USART0_ISO786=n
|
||||
|
||||
CONFIG_AVR32_USART1=y
|
||||
CONFIG_AVR32_USART1_RS232=y
|
||||
CONFIG_AVR32_USART1_SPI=n
|
||||
CONFIG_AVR32_USART1_RS485=n
|
||||
CONFIG_AVR32_USART1_MAN=n
|
||||
CONFIG_AVR32_USART1_MODEM=n
|
||||
CONFIG_AVR32_USART1_IRDA=n
|
||||
CONFIG_AVR32_USART1_ISO786=n
|
||||
|
||||
CONFIG_AVR32_USART2=n
|
||||
CONFIG_AVR32_USART2_RS232=n
|
||||
CONFIG_AVR32_USART2_SPI=n
|
||||
CONFIG_AVR32_USART2_RS485=n
|
||||
CONFIG_AVR32_USART2_MAN=n
|
||||
CONFIG_AVR32_USART2_MODEM=n
|
||||
CONFIG_AVR32_USART2_IRDA=n
|
||||
CONFIG_AVR32_USART2_ISO786=n
|
||||
|
||||
#
|
||||
# AVR32 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
|
||||
# console and ttys0 (default is the USART0).
|
||||
# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_USARTn_BAUD - The configure BAUD of the USART. Must be
|
||||
# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_USARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_USART0_SERIAL_CONSOLE=n
|
||||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||||
CONFIG_USART2_SERIAL_CONSOLE=n
|
||||
|
||||
CONFIG_USART0_TXBUFSIZE=256
|
||||
CONFIG_USART1_TXBUFSIZE=256
|
||||
CONFIG_USART2_TXBUFSIZE=256
|
||||
|
||||
CONFIG_USART0_RXBUFSIZE=256
|
||||
CONFIG_USART1_RXBUFSIZE=256
|
||||
CONFIG_USART2_RXBUFSIZE=256
|
||||
|
||||
CONFIG_USART0_BAUD=57600
|
||||
CONFIG_USART1_BAUD=57600
|
||||
CONFIG_USART2_BAUD=57600
|
||||
|
||||
CONFIG_USART0_BITS=8
|
||||
CONFIG_USART1_BITS=8
|
||||
CONFIG_USART2_BITS=8
|
||||
|
||||
CONFIG_USART0_PARITY=0
|
||||
CONFIG_USART1_PARITY=0
|
||||
CONFIG_USART2_PARITY=0
|
||||
|
||||
CONFIG_USART0_2STOP=0
|
||||
CONFIG_USART1_2STOP=0
|
||||
CONFIG_USART2_2STOP=0
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=y
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=n
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APP_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX.
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz
|
||||
# or TICKS_PER_MSEC=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to
|
||||
# handle delayed processing from interrupt handlers. This feature
|
||||
# is required for some drivers but, if there are not complaints,
|
||||
# can be safely disabled. The worker thread also performs
|
||||
# garbage collection -- completing any delayed memory deallocations
|
||||
# from interrupt handlers. If the worker thread is disabled,
|
||||
# then that clean will be performed by the IDLE thread instead
|
||||
# (which runs at the lowest of priority and may not be appropriate
|
||||
# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE
|
||||
# is enabled, then the following options can also be used:
|
||||
# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
|
||||
# thread. Default: 50
|
||||
# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
|
||||
# work in units of microseconds. Default: 50*1000 (50 MS).
|
||||
# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
|
||||
# thread. Default: CONFIG_IDLETHREAD_STACKSIZE.
|
||||
# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
|
||||
# the worker thread. Default: 4
|
||||
#
|
||||
CONFIG_APP_DIR=examples/nsh
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=0
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2010
|
||||
CONFIG_START_MONTH=11
|
||||
CONFIG_START_DAY=2
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=n
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_NXFLAT=n
|
||||
CONFIG_SCHED_WORKQUEUE=n
|
||||
CONFIG_SCHED_WORKPRIORITY=50
|
||||
CONFIG_SCHED_WORKPERIOD=(50*1000)
|
||||
CONFIG_SCHED_WORKSTACKSIZE=1024
|
||||
CONFIG_SIG_SIGWORK=4
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=n
|
||||
CONFIG_DISABLE_PTHREAD=n
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=n
|
||||
CONFIG_DISABLE_MOUNTPOINT=n
|
||||
CONFIG_DISABLE_ENVIRON=n
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_STRNLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
CONFIG_ARCH_KMALLOC=n
|
||||
CONFIG_ARCH_KZMALLOC=n
|
||||
CONFIG_ARCH_KFREE=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=8
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=256
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
CONFIG_FS_FAT=y
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# Block driver buffering
|
||||
#
|
||||
# CONFIG_FS_READAHEAD
|
||||
# Enable read-ahead buffering
|
||||
# CONFIG_FS_WRITEBUFFER
|
||||
# Enable write buffering
|
||||
#
|
||||
CONFIG_FS_READAHEAD=n
|
||||
CONFIG_FS_WRITEBUFFER=n
|
||||
|
||||
#
|
||||
# SDIO-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_SDIO_DMA
|
||||
# SDIO driver supports DMA
|
||||
# CONFIG_MMCSD_MMCSUPPORT
|
||||
# Enable support for MMC cards
|
||||
# CONFIG_MMCSD_HAVECARDDETECT
|
||||
# SDIO driver card detection is 100% accurate
|
||||
#
|
||||
CONFIG_SDIO_DMA=n
|
||||
CONFIG_MMCSD_MMCSUPPORT=n
|
||||
CONFIG_MMCSD_HAVECARDDETECT=n
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_LLH_LEN - The link level header length
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=n
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=0
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=420
|
||||
CONFIG_NET_TCP=n
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_UDP=n
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=10
|
||||
CONFIG_NET_ICMP=n
|
||||
CONFIG_NET_ICMP_PING=n
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_LLH_LEN=14
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# USB Device Configuration
|
||||
#
|
||||
# CONFIG_USBDEV
|
||||
# Enables USB device support
|
||||
# CONFIG_USBDEV_ISOCHRONOUS
|
||||
# Build in extra support for isochronous endpoints
|
||||
# CONFIG_USBDEV_DUALSPEED
|
||||
# Hardware handles high and full speed operation (USB 2.0)
|
||||
# CONFIG_USBDEV_SELFPOWERED
|
||||
# Will cause USB features to indicate that the device is
|
||||
# self-powered
|
||||
# CONFIG_USBDEV_MAXPOWER
|
||||
# Maximum power consumption in mA
|
||||
# CONFIG_USBDEV_TRACE
|
||||
# Enables USB tracing for debug
|
||||
# CONFIG_USBDEV_TRACE_NRECORDS
|
||||
# Number of trace entries to remember
|
||||
#
|
||||
CONFIG_USBDEV=n
|
||||
CONFIG_USBDEV_ISOCHRONOUS=n
|
||||
CONFIG_USBDEV_DUALSPEED=n
|
||||
CONFIG_USBDEV_SELFPOWERED=y
|
||||
CONFIG_USBDEV_REMOTEWAKEUP=n
|
||||
CONFIG_USBDEV_MAXPOWER=100
|
||||
CONFIG_USBDEV_TRACE=n
|
||||
CONFIG_USBDEV_TRACE_NRECORDS=128
|
||||
|
||||
#
|
||||
# AVR32 USB Configuration
|
||||
#
|
||||
|
||||
#
|
||||
# USB Serial Device Configuration
|
||||
#
|
||||
# CONFIG_USBSER
|
||||
# Enable compilation of the USB serial driver
|
||||
# CONFIG_USBSER_EPINTIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# interrupt IN operation
|
||||
# CONFIG_USBSER_EPBULKOUT
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk OUT operation
|
||||
# CONFIG_USBSER_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoint that supports
|
||||
# bulk IN operation
|
||||
# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
|
||||
# Size of the serial receive/transmit buffers
|
||||
#
|
||||
CONFIG_USBSER=n
|
||||
CONFIG_USBSER_EPINTIN=1
|
||||
CONFIG_USBSER_EPBULKOUT=2
|
||||
CONFIG_USBSER_EPBULKIN=5
|
||||
CONFIG_USBSER_NWRREQS=4
|
||||
CONFIG_USBSER_NRDREQS=4
|
||||
CONFIG_USBSER_VENDORID=0x067b
|
||||
CONFIG_USBSER_PRODUCTID=0x2303
|
||||
CONFIG_USBSER_VENDORSTR="Nuttx"
|
||||
CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
|
||||
CONFIG_USBSER_RXBUFSIZE=512
|
||||
CONFIG_USBSER_TXBUFSIZE=512
|
||||
|
||||
#
|
||||
# USB Storage Device Configuration
|
||||
#
|
||||
# CONFIG_USBSTRG
|
||||
# Enable compilation of the USB storage driver
|
||||
# CONFIG_USBSTRG_EP0MAXPACKET
|
||||
# Max packet size for endpoint 0
|
||||
# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
|
||||
# The logical 7-bit address of a hardware endpoints that support
|
||||
# bulk OUT and IN operations
|
||||
# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
|
||||
# The number of write/read requests that can be in flight
|
||||
# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
|
||||
# The size of the buffer in each write/read request. This
|
||||
# value needs to be at least as large as the endpoint
|
||||
# maxpacket and ideally as large as a block device sector.
|
||||
# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
|
||||
# The vendor ID code/string
|
||||
# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
|
||||
# The product ID code/string
|
||||
# CONFIG_USBSTRG_REMOVABLE
|
||||
# Select if the media is removable
|
||||
#
|
||||
CONFIG_USBSTRG=n
|
||||
CONFIG_USBSTRG_EP0MAXPACKET=64
|
||||
CONFIG_USBSTRG_EPBULKOUT=2
|
||||
CONFIG_USBSTRG_EPBULKIN=5
|
||||
CONFIG_USBSTRG_NRDREQS=2
|
||||
CONFIG_USBSTRG_NWRREQS=2
|
||||
CONFIG_USBSTRG_BULKINREQLEN=256
|
||||
CONFIG_USBSTRG_BULKOUTREQLEN=256
|
||||
CONFIG_USBSTRG_VENDORID=0x584e
|
||||
CONFIG_USBSTRG_VENDORSTR="NuttX"
|
||||
CONFIG_USBSTRG_PRODUCTID=0x5342
|
||||
CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
|
||||
CONFIG_USBSTRG_VERSIONNO=0x0399
|
||||
CONFIG_USBSTRG_REMOVABLE=y
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=1024
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for examples/nsh
|
||||
#
|
||||
# CONFIG_EXAMPLES_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_EXAMPLES_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_EXAMPLES_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_EXAMPLES_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_EXAMPLES_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_EXAMPLES_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_EXAMPLES_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_EXAMPLES_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_EXAMPLES_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_EXAMPLES_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_TELNET is selected:
|
||||
# CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_EXAMPLES_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_EXAMPLES_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_EXAMPLES_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_EXAMPLES_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_EXAMPLES_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_ROMFSETC is selected:
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_EXAMPLES_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_EXAMPLES_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_FILEIOSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_STRERROR=n
|
||||
CONFIG_EXAMPLES_NSH_LINELEN=64
|
||||
CONFIG_EXAMPLES_NSH_STACKSIZE=1024
|
||||
CONFIG_EXAMPLES_NSH_NESTDEPTH=3
|
||||
CONFIG_EXAMPLES_NSH_DISABLESCRIPT=n
|
||||
CONFIG_EXAMPLES_NSH_DISABLEBG=n
|
||||
CONFIG_EXAMPLES_NSH_ROMFSETC=n
|
||||
CONFIG_EXAMPLES_NSH_CONSOLE=y
|
||||
CONFIG_EXAMPLES_NSH_TELNET=n
|
||||
CONFIG_EXAMPLES_NSH_ARCHINIT=n
|
||||
CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_EXAMPLES_NSH_DHCPC=n
|
||||
CONFIG_EXAMPLES_NSH_NOMAC=n
|
||||
CONFIG_EXAMPLES_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLES_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLES_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_EXAMPLES_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_EXAMPLES_NSH_ROMFSDEVNO=0
|
||||
CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_EXAMPLES_NSH_FATDEVNO=1
|
||||
CONFIG_EXAMPLES_NSH_FATSECTSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_FATNSECTORS=1024
|
||||
CONFIG_EXAMPLES_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Settings for examples/usbserial
|
||||
#
|
||||
# CONFIG_EXAMPLES_USBSERIAL_INONLY
|
||||
# Only verify IN (device-to-host) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
|
||||
# Only verify OUT (host-to-device) data transfers. Default: both
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
|
||||
# Send only small, single packet messages. Default: Send large and small.
|
||||
# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
|
||||
# Send only large, multi-packet messages. Default: Send large and small.
|
||||
#
|
||||
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
|
||||
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
||||
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should always be =y for this AVR32 which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=y
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
||||
105
configs/avr32dev1/nsh/ld.script
Executable file
105
configs/avr32dev1/nsh/ld.script
Executable file
@ -0,0 +1,105 @@
|
||||
/****************************************************************************
|
||||
* configs/avr32dev1/nsh/ld.script
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
OUTPUT_FORMAT("elf32-avr32", "elf32-avr32", "elf32-avr32")
|
||||
OUTPUT_ARCH(avr32:uc)
|
||||
ENTRY(_stext)
|
||||
|
||||
/* The following assumes that the bootloader resides at 0x8000:0000 and so
|
||||
* links the application to execute after the bootloader at 0x8000:2000.
|
||||
* To link so that NuttX boots directly without using the bootloader,
|
||||
* change the flash definition to:
|
||||
*
|
||||
* flash (rxai!w) : ORIGIN = 0x80000000, LENGTH = 256K
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rxai!w) : ORIGIN = 0x80002000, LENGTH = 256K - 8K
|
||||
intram (wxa!ri) : ORIGIN = 0x00000004, LENGTH = 32K
|
||||
userpage : ORIGIN = 0x80800000, LENGTH = 512
|
||||
factorypage : ORIGIN = 0x80800200, LENGTH = 512
|
||||
}
|
||||
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.); /* See below */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > intram AT > flash
|
||||
|
||||
.bss : { /* BSS */
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > intram
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
||||
|
||||
57
configs/avr32dev1/nsh/setenv.sh
Executable file
57
configs/avr32dev1/nsh/setenv.sh
Executable file
@ -0,0 +1,57 @@
|
||||
#!/bin/bash
|
||||
# configs/avr32dev1/nsh/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
#
|
||||
# This PATH setup assumes that you are using versin 2.1.4 of the Atmel
|
||||
# AVR GNU tools installed at the default location on Windows. NOTE
|
||||
# that the path is in appended to the end of the PATH variable; this is
|
||||
# because there are also many GNUWin32 binaries there that conflict with
|
||||
# Cygwin versions.
|
||||
#
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
|
||||
export AVR32_BIN="/cygdrive/c/Program Files/Atmel/AVR Tools/AVR32 Toolchain/bin/"
|
||||
export FLIP_BIN="/cygdrive/c/Program Files/Atmel/Flip 3.4.2/bin"
|
||||
export AVR32DEV1_BIN="${WD}/configs/avr32dev1/tools"
|
||||
export PATH="${FLIP_BIN}:${AVR32DEV1_BIN}:/sbin:/usr/sbin:${PATH_ORIG}:${AVR32_BIN}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
||||
@ -311,12 +311,12 @@ CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_RR_INTERVAL=0
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2010
|
||||
CONFIG_START_MONTH=6
|
||||
CONFIG_START_DAY=20
|
||||
CONFIG_START_MONTH=11
|
||||
CONFIG_START_DAY=2
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
@ -668,7 +668,7 @@ CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=1024
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
|
||||
Loading…
Reference in New Issue
Block a user