Cleaning during `clean_context` had the issue of remaking everything
when `menuconfig` was issued. That's because `menuconfig` has a
`clean_context` on its way.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
use the same condition check in declaration and reference
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I7b05316e914708fceeddac394d784ee3720a3c1b
since kernel component should use UTC instead local time
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Icf939e1ab0af8e577105f539d2553bc67b3b3d10
instead calling kmm_heapmember or umm_heapmember because:
1.The stack supplied by caller may allocate from heap too
2.It's hard to implement these two function in ASan case
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I196377822b7c4643ab4f29b7c1dc41dcd7c4dab1
All modern desgin support stack pointer and it's also an
important information, so let's standardize this interface.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
arch: Allocate the space from the beginning in up_stack_frame
and modify the affected portion:
1.Correct the stack dump and check
2.Allocate tls_info_s by up_stack_frame too
3.Move the stack fork allocation from arch to sched
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
All supported arch uses a push-down stack:
The stack grows toward lower addresses in memory. The stack pointer
register points to the lowest, valid working address (the "top" of
the stack). Items on the stack are referenced as positive(include zero)
word offsets from sp.
Which means that for stack in the [begin, begin + size):
1.The initial SP point to begin + size
2.push equals sub and then store
3.pop equals load and then add
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
IRQs cannot be individually disabled on the eZ80, so using
`up_disable_irq()` had no effect. This left the IRQ handler being
constantly triggered without the lower half handler running.
The macro for EMAC stats was incompatible with Clang. The simplified
form gives identical results under ZDS-II.
The MII clock speed must be set before trying to read MII registers.
It's now done before resetting the PHY using the Mode Control Register.
MII initialization waited on the auto-neogotiate restart bit being set
but PHY hardware is frequently fast enough to have cleared the bit
before the first read of it. It now instead just waits on auto-negotiate
completing. The MII poll loop now uses `up_mdelay` because it was far
too fast at 50MHz using a busy loop, giving time for a link to be
established.
Bad packets are now processed enough to release their buffers back to
the EMAC hardware.
A few typos, unused variables, and other miscellaneous issues were also
fixed.
Summary:
- During repeating ostest with sabre-6quad:smp (QEMU),
I noticed that pthread_rwlock_test sometimes stops
- Finally, I found that nxtask_exit() released a critical
section too early before context switching which resulted in
selecting inappropriate TCB
- This commit fixes this issue by moving nxsched_resume_scheduler()
from nxtask_exit() to up_exit() and also removing
spin_setbit() and spin_clrbit() from nxtask_exit()
because the caller holds a critical section
- To be consistent with non-SMP cases, the above changes
were done for all CPU architectures
Impact:
- This commit affects all CPU architectures regardless of SMP
Testing:
- Tested with ostest with the following configs
- sabre-6quad:smp (QEMU, dev board), sabre-6quad:nsh (QEMU)
- spresense:wifi_smp
- sim:smp, sim:ostest
- maix-bit:smp (QEMU)
- esp32-devkitc:smp (QEMU)
- lc823450-xgevk:rndis
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
In the current compilation environment, the recursive assignment(=) for compile
flags will be delayed until every file is actually need to be compile.
For example:
--------------------------------------------------------------------------------
arch/arm/src/Makefile:
INCLUDES += ${shell $(INCDIR) "$(CC)" $(ARCH_SRCDIR)$(DELIM)chip}
INCLUDES += ${shell $(INCDIR) "$(CC)" $(ARCH_SRCDIR)$(DELIM)common}
INCLUDES += ${shell $(INCDIR) "$(CC)" $(ARCH_SRCDIR)$(DELIM)$(ARCH_SUBDIR)}
INCLUDES += ${shell $(INCDIR) "$(CC)" $(TOPDIR)$(DELIM)sched}
CPPFLAGS += $(INCLUDES) $(EXTRAFLAGS)
CFLAGS += $(INCLUDES) $(EXTRAFLAGS)
CXXFLAGS += $(INCLUDES) $(EXTRAFLAGS)
AFLAGS += $(INCLUDES) $(EXTRAFLAGS)
--------------------------------------------------------------------------------
All compilation options will be included recursively,
which will be delayed until the compilation options are actually used:
tools/Config.mk:
--------------------------------------------------------------------------------
define COMPILE
@echo "CC: $1"
$(Q) $(CC) -c $(CFLAGS) $($(strip $1)_CFLAGS) $1 -o $2
endef
--------------------------------------------------------------------------------
All compile flags to be reexecuted $(INCDIR) as long as one file needs to be compiled,
but in fact, the compilation options have not changed in the current directory.
So the we recommand to change the syntax of assignment
From
Recursive (=)
To
Simple (:=)
In this way, we can ensure that all compilation options are expanded only once and reducing repeated works.
Signed-off-by: chao.an <anchao@xiaomi.com>
