nrf24l01: fix PIPENO/PKTLEN bitmask in rx fifo header
In RX fifo header, the first byte should use 5 lsb to store PKTLEN
and 3 msb to store PIPENO. However, FIFO_PIPENO_SHIFT was set to 4
which causes the lsb of pipe number to interfere with the received
packet size stored in the fifo.
This fix rx corruption when using pipe number > 0.
Signed-off-by: Federico Braghiroli <federico.braghiroli@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
NOTE: There's one change that might be incorrect, where I skip interfaces with zero endpoints. I did this because my device has two consecutive interface descriptors with the same interface number, one for altsetting 0 with no endpoints, and another for altsetting 1 with 1 endpoint. The loop was aborting due to finding two interface descriptors back-to-back.
configs: spresense: enable BMI160_I2C sensor
* drivers: sensors: add BMI160 driver
Enable driver support for the Bosch BMI160 Inertial
Measurement sensor
This driver can be used with the BMI160 sensor connected over
SPI or I2C bus
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable BMI160_I2C sensor
Enable BMI160 sensor connected over I2C on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/mmcsd: Fixes bug where thread gets deadlocked due to recursive call and addresses comment regarding events.
When initializing the MMCSD, if we are being told there is a card, but we fail to initialize it, we should not re-register for an insertion event as this will immediately cause us to call in again. Instead, we should register for a removal event and wait for the card to be removed and re-inserted.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
nrf24l01: don't block in read if file descriptor is O_NONBLOCK
nrf24l01: support for "multicast" TX mode - no waiting for ACK (needs to be enabled with fcntl SETTXPAYLOADNOACK)
Approved-by: Gregory Nutt <gnutt@nuttx.org>
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
Add some I2C devices to nucleo-h743zi and a few small fixes
configs/nucleo-h743zi: add support for ssd1306
configs/nucleo-h743zi: add support for pca9635
configs/nucleo-h743zi: add support for i2ctools
include/nuttx/sensors/lsm6dsl.h: remove whitespaces
configs/stm32f103-minimum/src/stm32_ssd1306.c: cosmetics
Documentation/NuttxPortingGuide.html: vsyslog return none
drivers/syslog/README.txt: vsyslog return none
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/stm32/stm32_i2s.c: In debug assertions, it on a sample rate of 0, but based on other code comments this value implies disabling the i2s master clock.
arch/arm/src/stm32/stm32_usbhost.h and arch/arm/src/stm32/Kconfig: Allow vbus monitoring for the OTG_HS host driver.
