1. Should check the vmid in ivshmem_remove() when release irq instead
check the ivdev->reg;
2. Add vmid check in ivshmem_probe() because ivshmem driver only support
vmid == 0 or 1 for now in NuttX;
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
Add common ivshmem driver, provide the ivshmem bus mechisam, so
many ivshmem based driver can change to pci_ivshmem based
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
Rptun is a rptun fremework driver base on the Inter-Virtual Machine
Share Memory Device.
With this driver, two NuttX runs in different QEMU can communicate
with each other by the rpmsg api.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
We can see them in ifconfig:
ap> ifconfig
wlan0 Link encap:Ethernet HWaddr 42:64:7f:b3:12:03 at UP mtu 1500
inet addr:10.0.1.2 DRaddr:10.0.1.1 Mask:255.255.255.0
inet6 DRaddr: ::
RX: Received Fragment Errors Bytes
00000b9b 00000000 00000000 21daf5
IPv4 IPv6 ARP Dropped
00000a33 00000137 00000031 00000000
TX: Queued Sent Errors Timeouts Bytes
00000ac4 00000ac4 00000000 00000000 1a2103
Total Errors: 00000000
Signed-off-by: meijian <meijian@xiaomi.com>
Coredump need call the block read/write ops in interrupt
Not consider the ops called in thread and intterupt simultaneously.
Only used for coredump now.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
SO_SNDBUF takes effect only after the connection in STREAM mode
is successful
support full life cycle modification of SO_RCVBUF
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
because if priv->rx_length is zero , need to call SPIS_CTRLR_QPOLL to
receive new data from lower half and update priv->rx_length.
This reverts commit 6cb649ecf6.
prevent the server list in resolv.conf from increasing indefinitely
the one that is overwritten is always the one configured first.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
The file descriptors of kernel threads should be clean and should
not be generated based on user threads. Instead, an idle thread
hould be chosen.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
Since the introduction of the rp2350, the pico-sdk project has been
re-arranged and elf2uf2 has been merged in to a new 'picotool' binary
which is supplied and installed separately.
Configuring NuttX and compile:
$ ./tools/configure.sh -l qemu-armv8a:nsh_smp
$ make
Running with qemu
$ qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic \
-machine virt,virtualization=on,gic-version=3 \
-net none -chardev stdio,id=con,mux=on -serial chardev:con \
-mon chardev=con,mode=readline -kernel ./nuttx
reason:
If the type of tcb is TSTATE_TASK_ASSIGNED, removing it using nxsched_remove_not_running
and then putting it back into the queue may result in a context switch.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
