rgbled: Fixes led issues caused by uninitialized memory with CONFIG_RGBLED_MULTICHAN.
The uninitialized pwm_info_s struct caused a rogue channel to be started causing errros in the pwm driver
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
include/nuttx/wireless/ieee80211: Cosmetic, coding standard changes from review of last merge.
drivers/wireless/ieee80211: Cosmetic, coding standard changes from review of last merge.
configs/photon: Cosmetic, coding standard changes from review of last merge.
arch/arm/src/stm32: SDIO changes from last review: Fix a few long lines and other coding standard issues; Make additions for SDIO card support dependent on a configuration option.
Author: hhuysqt <hyq9606@126.com>
Return IEEE 802.11 MAC address just as ethernet does
Modifyed bcmf_board_setup_oob_irq declaration
Modified OOB ISR function types
Add some logic according to WICED SDK
Bug fixed: data_offset counts in 4-bytes
Add BCM43438 logic for future developement
Add tips on using telnet
Use SDIO in-band interrupt instead of OOB interrupt, because Photon seems to unconnect the OOB interrupt line...
add SDIO in-band interrupt logic
drivers/1wire: add PM hooks and unlink support to sht21 sensor (allowing hot-swappable I2C bus from 1-wire converter)
* drivers/1wire: add PM hook to 1wire bus
* drivers/1wire/ds28e17.c: i2c instance must be zeroed
* drivers/sht21: add unlink support
Unlike most other unlink implementations in NuttX drivers, this one
does not allow any I2C operations after unlink, making it possible to
deallocate the I2C bus.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/net: Add TAP (network bridge) mode to tun.c
In previous implementation, TAP mode did not handle a packet
correctly. Also, the driver did not set the link layer type and
could not assign the interface name. This PR changes fix such
issues and supports TAP mode correctly.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Xbee: Adds a timeout to send logic to handle case where XBee module fails to respond to a Transmit request with a Transmit Status
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm/src/stm32: Add Kconfig options needed by the HCI UART. Various fixes to finally get a clean error free compile with no unexpected warnings.
arch/arm/src/stm32: In HCI UART, use spin_lock_irqsave() instead of enter_critical_section() whenever possible.
arch/arm/src/stm32: In HCI UART, fix up naming of configurations so that they are unique. Still needs Kconfig settings. Modify logic so that there can be multiple HCI UARTs, some supporting DMA and some not.
arch/arm/src/stm32: Integrate watermarks and software Rx flow control into the HCI UART driver.
arch/arm/src/stm32: Eliminate some HCI UART UART configuration options. Per the HCI UART spec, the link will b 8 data bits, no parity, 1 stop bit... Always.
arch/arm/src/stm32: Trivial cleanup
arch/arm/src/stm32: Fixes most initial compilation issues STM32 HCI UART driver. Still need to set up USART configuration parmeters for HCI UART
arch/arm/src/stm32: Completes first cut at STM32 HCI UART driver.
arch/arm/src/stm32: Completes most of read logic for HCI UART. Still needs to be able to block if no read data is available. Still missing write and flush logic.
drivers/wireless: Remove txenable from HCI UART methods. arch/arm/src/stm32: Reorganize some structures in HCI UART.
arch/arm/src/stm32: Still messaging the HCI uart driver.
arch/arm/src/stm32: Some trivial renaming.
arch/arm/src/stm32: A little more HCI-UART logic.
arch/arm/src/stm32: Initial setup to support HCI-UART. Little more than the serial driver with some name changes and a few things removed.
Squashed merge of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
drivers/sensors: Fix some minor typos in last commit that cause some compile problems.
drivers/sensors/: Clean up some coding standard isses in LM330 and ADXL372 drivers.
drivers/sensors/README.txt: Clean up some long lines and odd line breaks.
include/nuttx/sensors: Completes coding style review of adxl372.h, cluster_driver.h, and lsm330.h.
Author: Bob Feretich <bob.feretich@rafresearch.com>
Add LSM330 SPI and ADXL372 drivers along with the cluster driver infrastructure.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Some cosmetic changes from coding style review.
Author: Juha Niskanen <juha.niskanen@haltian.com>
drivers/1wire: add 1-wire subsystem and ds28e17 driver
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Fix a few remaining refereces to cc3000.
Author: Alan Carvalho de Assis <acassis@gmail.com>
drivers/wireless/cc3000: emove the driver to support CC3000 because it doesn't use the USRSOCKET
Author: Alan Carvalho de Assis <acassis@gmail.com>
configs: Remove board support to CC3000 from all relevant configurations.
Author: Gregory Nutt <gnutt@nuttx.org>
configs/spark: Removes Spark board configuration. Still available in the Obsoleted repository. This is preparation for removal of CC3000 support by Alan Carvalho de Assis. If there is no CC3000 support, then there is no purpose in supporting the Spark either.
Change all Sony related copyright to conform with our company's internal rules.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
wireless/bluetooth: This completes the basic logic path that gets frames from the Bluetooth stack and into the network layer.
wireless/bluetooth: Fleshes out some of the network packet receive logic.
wireless/bluetooth: Replace buffer allocated with primitive allocator from ieee 802.15.4.
wireless/ieee802154: Fix a few typos.
wireless/bluetooth: More renaming in preparation for some real work.
wireless/bluetooth: Some trivial renaming; update comments
Squashed commit of the following:
wireless/bluetooth: Some small changes that gets to a clean compile by just eliminating some incorrect implementations (still with a lot of warnings. The logic is still incomplete but now not so lethal.
wireless/bluetooth: Restructuring: Connection interfaces should internal to wireless/bluetooth. include/nuttx/wireless/bt_conn.h removed and merged with wireless/bluetooth/bt_conn.h. Several fix to get closer to bt_netdev.c compiling. Need to design some not interfaces and use some existing interfaces to send and receiv packets.
wireless/bluetooth: Some organization with some network device compile errors fixed. Still not even close to compiling.
net/bluetooth: Fix numerous compile issues; Still open design issues with regard to the interface with the Bluetooth stack.
wireless/bluetooth: Create bt_netdev.c with a crude copy of mac802154_netdev.c. Does not not even compile yet.
include/nuttx/net: Add bluetooth.h. Content is not yet correct.
net/netpackets: Add bluetooth.h. Update net/bluetooth to use new socket address definition.
net/bluetooth: Some fixes for initial build.
net/bluetooth: Add initial support for Bluetooth sockets. The initial cut is just the a clone of the IEEE 802.15.4 socket support with name changes.
net/ieee802154: Fix some typos noted when cloning to create net/bluetooth.
Squashed commit of the following:
drivers/bluetooth: Re-architect Bluetooth UART driver to follow upper/lower half model. Completely untested.
drivers/bluetooth: Grr.. Another band-aid commit to stay in sync with master. Why is this so difficult
drivers/bluetooth: Band-aid commit to stay in sync with master. Lost it somehow.
drivers/wireless/bluetooth: A few changes, mostly thought experiments.
drivers/wireless/bluetooth: UART-based Bluetooth driver ported from the Intel/Zephyr arduino101_firmware_source-v1.tar package. This initial commit is the original files in the NuttX build environment with changes to conform with the coding standard. It should not even build.
drivers/lcd/ft80x: ACTIVE host command appears to be formatted differently than other host commands; Fix ROM CHIPID. Appears to be big-ending, BCD.
drivers/lcd/ft80x: Fix some compile issues when debug features are enabled.
Feature pca9540bdp i2cmultiplexer
* Implement common i2c multiplexer abstraction to be reused by i2c multiplexer devices. Provide common interface with transfer and reset calls to set up virtual i2c busses.
* Remove i2cmux_lower_half.c and headers, will be implemented by each mux driver
* Implement PCA9540BDP I2C multiplexer lower half which uses the common i2c mux abstraction
* Remove application interface and implement common i2c functions
* Remove application interface from pca driver and implement common i2c functions directly in the pca driver
* Use i2cerr
Approved-by: Gregory Nutt <gnutt@nuttx.org>
cc1101: Changes from review of last PR.
remove gpio
remove cc1101 frame len
remove FLAGS_RXONLY flags
add cc1101 function
remove some waring
add cc1101 poll function
add cc1101 register
add cc1101 isr read data
add cc1101 spi deviceId
add cc1101 init2
add wait cc1101 chip ready
raw init cc1101
Author: Juha Niskanen <juha.niskanen@haltian.com>
Date: Mon Feb 19 15:03:17 2018 -0600
drivers/mtd: mtd_config.c: Add still more error handling (to detect bad underlying flash implementations)
drivers/mtd: mtd_config.c: Remove MTD_ERASE that was erasing data block instead of erase block. This is a partial revert of 4f18b4. Reported-by: Pascal Speck <iktek01@yahoo.com>
arch/arm/src/stm32l4: stm32l4_flash: change flash programming to use page buffer for unaligned writes.
drivers/lcd and include/nuttx/lcd: Add FT80x support for writing to graphics memory. Also add some definitions needed by apps/examples/ft80x for bitmap manipulation.
drivers/lcd: Review/update FT80x initializatin logic
drivers/lcd: Rename ft80x_base.c to just ft80x.c. Add logic to notify FT80X clients of events via signals.
drivers/lcd: Trivial updates to naming. Add some new definitions.
Squashed commit of the following:
drivers/lcd: Finishes off basic FT80X. Still missing some niceties.
drivers/lcd: Rethink FT80X display list interface.
drivers/lcd: More FT800x display list logic. Still not complete.
drivers/lcd: Add some basic FT80x initialization logic.
drivers/lcd: Add ft80x display list IOCTL framework. Still missing low level display list operations.
drivers/lcd: FT80x driver cannot be a standard LCD driver but must, instead, be a custom character driver.
drivers/lcd: Add FT800 co-processor commands and display list helpers.
drivers/lcd: Add SPI interface and framework for the initialization and the basic LCD driver.
drivers/lcd: Add beginnings of some FT80x implementation.
drivers/lcd: Add definitions for the FTDI FT801 part
include/nuttx/lcd/ft800.h: Add initial FT800 interface definition.
drivers/lcd: Add ft800 header file.
Added support for LIS3DH accelerometer sensor.
* Added support for LIS3DH accelerometer sensor.
* Fix line length
* Fix more line lengthts
Approved-by: Gregory Nutt <gnutt@nuttx.org>
