1. Adjust code to avoid PM wakelock->count less than or equal to 0.
2. Fix some document format issues.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
These configs are changed based on below rules.
1. always enable +CONFIG_LV_USE_NUTTX=y
2. If touchpad is used, enable +CONFIG_LV_USE_NUTTX_TOUCHSCREEN=y
3. enable log by +CONFIG_LV_USE_LOG=y
4. If -CONFIG_LV_MEM_CUSTOM=y previously defined, replace it with +CONFIG_LV_USE_CLIB_MALLOC=y +CONFIG_LV_USE_CLIB_SPRINTF=y +CONFIG_LV_USE_CLIB_STRING=y
5. If -CONFIG_LV_PORT_USE_FBDEV=y, default config is for fbdev. If -CONFIG_LV_PORT_USE_LCDDEV=y, +CONFIG_LV_USE_NUTTX_LCD=y
6. Remove all -CONFIG_LV_TICK_CUSTOM=y -CONFIG_LV_TICK_CUSTOM_INCLUDE="port/lv_port_tick.h"
7. If -CONFIG_LV_PORT_LCDDEV_DOUBLE_BUFFER=y, replace it with CONFIG_LV_NUTTX_LCD_DOUBLE_BUFFER=y. For fbdev, double buffer is automatically detected.
8. If -CONFIG_LV_COLOR_16_SWAP=y, need to upgrade the LCD driver to support hardware byte order swap.
Signed-off-by: Xu Xingliang <xuxingliang@xiaomi.com>
This commit implements the common RMT driver (already available for
the other Espressif's xtensa-based devices) for ESP32.
This allows us to have a proper separation between the lower and
upper-half drivers and use the 'ws2812' example to drive WS2812 RGB
LEDs.
This commit updates the Wi-Fi and the BLE driver of ESP32. Most of
the changes rely on using the common sources and header files for
xtensa-based Espressif's SoCs.
The new Wi-Fi driver supports WPA3-SAE for both Station and SoftAP
mode. BLE's coexistence mode was enhanced according to the latest
libraries.
Please note that other sources required minor changes in order to
be compatible with the common sources.
This driver is used with QEMU, to make it possible
to use networking.
This is not the MAC in ESP32, however, it can be used with QEMU.
The code was shamelessly copied from 31dac92e5f
The board's microphone uses 24-bit i2s and this commit also fixes
the segmentation fault caused by the audio buffer overflow.
arch/xtensa/src/esp32/esp32_i2s.c: Fix bug regarding 24-bit audio and add AUDIOIOC_STOP to ioctl
drivers/audio/audio_i2s.c: Report number of channels on AUDIOIOC_GETCAPS
in boards/xtensa/esp32/esp32-sparrow-kit:
/configs/nsh/defconfig: Add I2S configs
/src/esp32-sparrow-kit.h: Add the signature of esp32_i2sdev_initialize()
/src/esp32_bringup.c: Add call to esp32_i2sdev_initialize()
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Enable with ./tools/configure.sh -l esp32-devkitc:dac
DAC channel 0 = GPIO 25
DAC channel 1 = GPIO 26
default path: /dev/dac0
Resolution 8 bits = values 0~255
Voltage: 0~Vref
The reference voltage 'Vref' here is input from the pin VDD3P3_RTC
which ideally equals to the power supply VDD (3.3V).
- A pre-built IDF bootloader is used by default;
- `ESP32_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32_PARTITION_TABLE.
The RMT (Remote Control) character driver allows to use the RMT
peripheral (usually, a one-wire peripheral dedicated to driving
IR remote control) as a character driver.
Please note that this perpiheral depends on the lower-half specific
driver implementation.
Once these messages are thrown during the system's bring-up, it is
advisable them to be output by the syslog considering the file
system initialization.
The SmartFS partition needs to be formatted before being mounted.
Otherwise, it would throw an error message. The error message now
contains a suggestion to format the partition when such an error
is detected.
This commit sets the BLE's interrupt as a IRAM-enabled interrupt,
which enables it to run during a SPI flash operation. This enables
us to create a cache to off-load semaphores and message queues
operations and treat them when the SPI flash operation is finished.
By doing that, we avoid packet losses during a SPI flash operation.
This commit provides an interface to register ISRs that run from
IRAM and keeps track of the non-IRAM interrupts. It enables, for
instance, to avoid disabling all the interrupts during a SPI flash
operation: IRAM-enabled ISRs are, then, able to run during these
operations.
It also makes the code look more similar to the ESP32-S3 SPI flash
implementation by creating a common `esp32_spiflash_init` that is
responsible to create the SPI flash operation tasks. The function
intended to initialize the SPI flash partions was, then, renamed to
`board_spiflash_init`.
Using up_textheap_memalign to allocate memory if arch support textheap
for loading section.
The default system heap does not support execution permissions,
so up_textheap_memalign allocation is required.
this patch can fix issue about #11043
update esp32 elf config:
remove -CONFIG_ARCH_USE_TEXT_HEAP=y becuase ARCH_CHIP_ESP32 select
ARCH_HAVE_TEXT_HEAP
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
- migrated /README are removed from /boards
- there are a lot of READMEs that should be further converted to rst.
At the moment they are moved to Documentation/platforms and included in rst files
