According to the specification, the close function must wait until all data
has been written before it closes the file (except O_NONBLOCK is set). The
maximum waiting time for this is not specified.
To be able to edit the file list of the process, the close function has to lock
the file list semaphore. After that the close function of the serial driver is
called.
Waiting for the complete transmission of all data is done in the serial driver.
This causes the semaphore to remain locked until all data has been sent.
However, no other thread of the process can edit the file list for that time
(open, close, dup2, etc.). This is not optimal in a multithreaded environment.
Therefore, we have to keep the waiting time within the driver as short as possible.
As a policy, all internal OS implementations must use "detached" files which are valid in any context and do not depend on the validity of a file descriptor at any point in time. This commit converts the usage of file descriptors to detached files throughout the local socket implementation.
Squashed commit of the following:
net/local: Finish change to eliminate use of file descriptors.
net/local: A little more of the conversion.
net/local: Beginning of chnages to eliminate use of file descriptors in the local socket implementeation. poll() will be a problem.
ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Fix GPIO operation of STMPE811 driver.
Fixed issues:
1. STMPE811_GPIO_DIR was defined for register name
and later was redefined to be the pin direction mask
for `stmpe811_gpioconfig`
I decided to change register name to be STMPE811_GPIO_DIR_REG,
and keep pin direction mask STMPE811_GPIO_DIR, so that any
external code that already use this driver will be unchanged.
2. The STMPE811 register GPIO_DIR uses bit value 1 for output
and 0 for input, but `stmpe811_gpioconfig` set the opposite.
3. The call to `stmpe811_gpiowrite` from inside of `stmpe811_gpioconfig`
leaded to deadlock.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
fs/userfs: This completes coding of the UserFS client and of the UserFS feature in general. This feature is being merged to main now because I believe it is innocuous. It is, however, untesed. The next step will be to develop a test case to verify the feature.
fs/userfs: Completes the request logic for the UserFS client. Still need the logic that receives the responses.
fs/userfs: Completes coding for most of the server side of the user filesystem logic.
fs/userfs: Big design changes, simplications. Use Unix domain local sockets instead of message queues. Easier to transfer big data in local sockets than message queues. Remove character drvier 'factory' it is not necessary.
fs/userfs: Minor reparitioning; volume private info does not need to be held on the OS client side.
libc/userfs: Add some of the server side logic.
fs/userfs: Add some UserFS initialization logic.
fs/userfs: Add frame work for the UserFS proxy. Remove all references to a block driver. There is no block dricer... what was I thinking?
fs/userfs: Add some initialization of the character driver, 'factory' device.
fs/userfs: Rename from fusefs to userfs to that we don't stomp on someone else's cool name.
Add a header file describing the fusefs interface.
Fix stm32 dmacapable on f20xx
* Fixed build for STM32F20XX platforms when CONFIG_STM32_DMACAPABLE is enabled
* Fixed build for STM32F20XX platforms when CONFIG_STM32_DMACAPABLE is enabled
Approved-by: Gregory Nutt <gnutt@nuttx.org>
