To ensure size_t same as toolchain definition in the first place and rename CXX_NEWLONG to ARCH_SIZET_LONG. The change also check whether __SIZE_TYPE__ exist before CONFIG_ARCH_SIZET_LONG so our definition can align with toolchain(gcc/clang) definition automatically.
This capability was erroneously removed by a previous commit. This setting is necessary when the C++ code generated by the compiler uses the new and delete operators provided in libs/libxx.
Here is an example of an error scenario where this capability is required:
1. CONFIG_CXX_NEWLONG=y in the defconfig file
2. This causes libs/libxx to to generate a delete operator of this form:
void delete(void*, unsigned long);
3. But the compiler expects to link with a delete operator of this form:
void delete(void*, unsigned int);
That results in a link-time failure and the ONLY solution for avoiding that link time failure (short of some complete redesign) is to have a control over the CONFIG_CXX_NEWLONG setting and make sture that it is always disabled for that toolchain.
Other toolchains will require that CONFIG_CXX_NEWLONG=y in all cases. This cannot be predicted because it is dependndent on the definitions provided by C libraries and header files that were build into binary toolchain.
CI should know the build status of testbuild.sh, so use -k make flag option as default
instead of -i ignore-error option. Then use fail to record build result. In addition,
refresh .config if toolchain updated.
Change-Id: I182c2b2db489e6ccb0a79fdc664072d19974c3ca
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
1.Scan the folder under nuttx/boards by prefix /
2.Skip the specified configuration by prefix -
Change-Id: Ibb67f2c6b96cd8e439d94bf71d098c1fd9e5a79d
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Make sure kconfig-tweak disables CONFIG_TOOLCHAIN_WINDOWS under linux host, or it would break the build when using testbuild.sh for some configs.
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
Author: Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h modified in PR through nxstyle.
Author: Masayuki Ishikawa <masayuki.ishikawa@gmail.com>
feature k210 (#16)
* arch: risc-v: Add support for __LP64__ to types.h
* arch: risc-v: Add support for RV64GC to common files
* arch: risc-v: Add support for Kendryte K210 processor (RV64GC)
* boards: risk-v: Add support for Sipeed Maix Bit with K210
* tools: Add support for Kendryte K210 processor
1. Serial (UART) driver (13 ports)
2. Ethernet driver
This port is provided on two boards
1. RSK RX65N-2MB
2. GR-Rose
The port is built on Cygwin environment.
As part of this port, we have created two documents
1. Readme.txt for each board
2. User manual to provide information about development environment setup
Both these documents are placed under
1. /boards/renesas/rx65n/rx65n-grrose
2. /boards/renesas/rx65n/rx65n-rsk2mb
We have run 'nxstyle' for coding guidelines and 'ostest' for testing NuttX features on test platform.
We have shared the log with no errors as confirmation of valid port.
The legacy '/' delimiter is still supported but not recommend and not advertised.
Squashed commit of the following:
Update configurations instructions in more README.txt files to show ':' delimiter vs '/' delimiter.
Update configurations instructions in various README.txt file to show ':' delimiter vs '/' delimiter.
tools: Update all configuration-related tools to accept ':' separator between board and configuration name.
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
On CI we want to know ASAP of a failure. This adds the
-x (exit on build failures) option to faclitate that
behavior.
Use ${MAKE} ${MAKE_FLAGS} for make invocation.
When -x is provided change MAKE_FLAGS to
--silent --no-print-directory and set -e
Ignore exit status when using grep for checking
for CONFIG_NXWM=y
