This adds a config flag to remove manual bclksclk training if one wants
to just use the controller's own training.
Manual addcmd training depends on the manual bclksclk training, so this
also adds this dependency in Kconfig.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Decreasing the value may increase DQ/DQS window size. Keep the default value
(1) for the existing board configurations.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Adds a platform specific implementation for tickless schedular operation. This includes:
- Tickless operation for vexriscv cores.
- Tickless operation for vexriscv-smp cores.
- Ticked operation for vexriscv-smp cores.
Ticked operation for vexriscv core has been refactored.
Additional default configuration added to demonstrate operation.
Both tickless and ticked options use Litex timer0 for scheduling intervals. This is significantly faster than interfaceing with the risc-v mtimer through opensbi.
Adding the CONFIG_ARCH_PERF_EVENTS configuration to enable
hardware performance counting，solve the problem that some platform
hardware counting support is not perfect, you can choose to use
software interface.
This is configured using CONFIG_ARCH_PERF_EVENTS, so weak_functions
are removed to prevent confusion
To use hardware performance counting, must:
1. Configure CONFIG_ARCH_PERF_EVENTS, default selection
2. Call up_perf_init for initialization
Signed-off-by: wangming9 <wangming9@xiaomi.com>
1. virtio devics/drivers match and probe/remote mechanism;
2. virtio mmio transport layer based on OpenAmp (Compatible with both
virtio mmio version 1 and 2);
3. virtio-serial driver based on new virtio framework;
4. virtio-rng driver based on new virtio framework;
5. virtio-net driver based on new virtio framework
(IOB Offload implementation);
6. virtio-blk driver based on new virtio framework;
7. Remove the old virtio mmio framework, the old framework only
support mmio transport layer, and the new framwork support
more transport layer and this commit has implemented all the
old virtio drivers;
8. Refresh the the qemu-arm64 and qemu-riscv virtio related
configs, and update its README.txt;
New virtio-net driver has better performance
Compared with previous virtio-mmio-net:
| | master/-c | master/-s | this/-c | this/-s |
| :--------------------: | :-------: | :-------: | :-----: | :-----: |
| qemu-armv8a:netnsh | 539Mbps | 524Mbps | 906Mbps | 715Mbps |
| qemu-armv8a:netnsh_smp | 401Mbps | 437Mbps | 583Mbps | 505Mbps |
| rv-virt:netnsh | 487Mbps | 512Mbps | 760Mbps | 634Mbps |
| rv-virt:netnsh_smp | 387Mbps | 455Mbps | 447Mbps | 502Mbps |
| rv-virt:netnsh64 | 602Mbps | 595Mbps | 881Mbps | 769Mbps |
| rv-virt:netnsh64_smp | 414Mbps | 515Mbps | 491Mbps | 525Mbps |
| rv-virt:knetnsh64 | 515Mbps | 457Mbps | 606Mbps | 540Mbps |
| rv-virt:knetnsh64_smp | 308Mbps | 389Mbps | 415Mbps | 474Mbps |
Note: Both CONFIG_IOB_NBUFFERS=64, using iperf command, all in Mbits/sec
Tested in QEMU 7.2.2
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
VELAPLATFO-12536
This provides the initial hooks for Flattened Device Tree support
with QEMU RV. It also provides a new procfs file that exposes the
fdt to userspace much like the /sys/firmware/fdt endpoint in Linux.
See https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-firmware-ofw
Nodes in the fdt are not yet usable by the OS.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Signed-off-by: liaoao <liaoao@xiaomi.com>
This PR adds support for the StarFive JH7110 RISC-V SoC. This will be used by the upcoming port of NuttX for PINE64 Star64 SBC. [The source files are explained in the articles here](https://github.com/lupyuen/nuttx-star64)
Modified Files in arch/risc-v:
Kconfig: Added ARCH_CHIP_JH7110 for JH7110 SoC
New Files in arch/risc-v:
include/jh7110/chip.h: JH7110 Definitions
include/jh7110/irq.h: Support 127 External Interrupts
src/jh7110/chip.h: Interrupt Stack Macro
src/jh7110/jh7110_allocateheap.c: Kernel Heap
src/jh7110/jh7110_head.S: Linux Header and Boot Code
src/jh7110/jh7110_irq.c: Configure Interrupts
src/jh7110/jh7110_irq_dispatch.c: Dispatch Interrupts
src/jh7110/jh7110_memorymap.h: Memory Map
src/jh7110/jh7110_mm_init.c, jh7110_mm_init.h: Memory Mgmt
src/jh7110/jh7110_pgalloc.c: Page Allocator
src/jh7110/jh7110_start.c: Startup Code
src/jh7110/jh7110_timerisr.c: Timer Interrupt
src/jh7110/hardware/jh7110_memorymap.h: PLIC Base Address
src/jh7110/hardware/jh7110_plic.h: PLIC Register Addresses
src/jh7110/Kconfig: JH7110 Config
src/jh7110/Make.defs: Makefile
When supporting high-priority interrupts, updating the
g_running_tasks within a high-priority interrupt may be
cause problems. The g_running_tasks should only be updated
when it is determined that a task context switch has occurred.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
Instead of clearing the fields individually, just wipe the whole register.
This can be done because flags and rm are just parts of the fcsr.
31 8 5 0
+--------------+--------+-----------+
| | | |
| RESERVED | FRM | FSTATUS |
| | | |
+--------------+--------+-----------+
FCSR
- Save the FPU registers into the tcb so they don't get lost if the stack
frame for xcp.regs moves (as it does)
- Handle interger and FPU register save/load separately
- Integer registers are saved/loaded always, like before
- FPU registers are only saved during a context switch:
- Save ONLY if FPU is dirty
- Restore always if FPU has been used (not in FSTATE_OFF, FSTATE_INIT)
- Remove all lazy-FPU related logic from the macros, it is not needed
Why? The tcb can contain info that is needed by the context switch
routine. One example is lazy-FPU handling; the integer registers can
be stored into the stack, because they are always stored & restored.
Lazy-FPU however needs a non-volatile location to store the FPU registers
as the save feature will skip saving a clean FPU, but the restore must
always restore the FPU registers if the thread uses FPU.
Basically, it reserves an area of the RTC memory to preserve the
RTC timer.
Please refer to:
fa76c82a5b
This commit also removes the rtc.dummy section because C3, C6 and
H2 don't need to skip it once the region is accessed by the same
address space using the instruction and data bus.
1. add lib_fork api in libs/libc, we need a fork() api to implement the
fork relative method, such as pthread_atfork
2. rename the assembly fork entry function name to up_fork(), and rename
the up_fork() to arch specific name, such as
sim_fork()/arm_fork()/mips_fork() etc.
Signed-off-by: guoshichao <guoshichao@xiaomi.com>
Clone the esp-hal-3rdparty repository and, then, checkout to a
specific version (usually indicated by the commit SHA) instead of
using a branch as the HEAD.
Also switch to automatic one by default, as it saves a lot of flash. The manual training
code is left in for now to be able to use it as an option if there are problems with automatic one
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The implementation of up_perf_*() is in a different static library in nuttx:
Hardware: libarch.a
Software: libdrivers.a (weak function)
Since functions with weak attributes cannot be correctly replaced in multiple static libraries,
this PR will use macros to replace whether the arch supports hardware perf events
Signed-off-by: chao an <anchao@xiaomi.com>
If -fstack-protector-all is enabled, gcc linker will need GCC
SSP(Stack Smashing Protector) support, Since the implement of SSP
is related to the OS, most of embedded toolchain does not provide
ssp support, so an error will be reported when linking:
enable CONFIG_LTO_FULL && CONFIG_STACK_CANARIES
arm-none-eabi/bin/ld: cannot find -lssp_nonshared: No such file or directory
arm-none-eabi/bin/ld: cannot find -lssp: No such file or directory
https://github.com/gcc-mirror/gcc/blob/master/gcc/gcc.cc#L983-L985
Since nuttx has already implemented SSP related hook functions,
so in this PR, we filter out this option in the link phase to ensure that
the implementation of lssp/lssp_nonshared will not be referenced
Signed-off-by: chao an <anchao@xiaomi.com>
Writes to MPFS_CFG_DDR_SGMII_PHY_EXPERT_DFI_STATUS_OVERRIDE register were not done properly. Use correct address for writes.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Reading the CSD field misses 3 bytes as the residual bytes
are not carried over properly. Fix this by adding the missing
bytes due to shifting.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Remove TABs
Fix indentation
Fix Multi-line comments
Fix Comments to the Right of Statements.
Fix nuttx coding style
Fix Comments to the Right of Statements.
1. as we can use fork to implement vfork, so we rename the vfork to
fork, and use the fork method as the base to implement vfork method
2. create the vfork function as a libc function based on fork
function
Signed-off-by: guoshichao <guoshichao@xiaomi.com>
Reference:https://xpack.github.io/blog/2022/05/18/riscv-none-elf-gcc-v12-1-0-2-released/
RISC-V ISA updates
Compared to previous releases, starting from 12.x, the compiler implements the new RISC-V ISA, which introduces an incompatibility issue, and builds might throw error messages like unrecognized opcode csrr.
The reason is that csr read/write (csrr*/csrw*) instructions and fence.i instruction were separated from the I extension, becoming two standalone extensions: Zicsr and Zifencei.
The solution is to add _zicsr and/or _zifencei to the -march option, e.g. -march=rv32imac becomes -march=rv32imac_zicsr_zifencei.
