ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Change all calls to mq_receive() and mq_timedreceive() in the OS to calls to nxmq_receive() and nxmq_timedreceive(), making appropriate changes for differences in return values.
sched/mqueue: Add nxmq_receive() and mxmq_timedreceive() which are functionally equivalent to the standard mq_receive and mq_timedreceive() except that (1) they do not create cancellation points, and (2) the do not modify the application's errno variable.
Change all calls to mq_send() and mq_timedsend() in the OS to calls to nxmq_send() and nxmq_timedsend(), making appropriate changes for differences in return values.
sched/mqueue: Add internal function nxmq_send() and nxmq_timedsend() that are equivalent to mq_send() and mq_timedsend() except that they do not create cancellation points and do to not modify the errno variable.
Replace all calls to sigqueue() in the OS proper with calls to nxsig_queue() to avoid accessing the errno variable.
sched/signal: Add nxsig_queue() which is functionally equivalent to sigqueue() except that it does not modify the errno variable.
Squashed commit of the following:
Change all calls to usleep() in the OS proper to calls to nxsig_usleep()
sched/signal: Add a new OS internal function nxsig_usleep() that is functionally equivalent to usleep() but does not cause a cancellaption point and does not modify the errno variable.
sched/signal: Add a new OS internal function nxsig_sleep() that is functionally equivalent to sleep() but does not cause a cancellaption point.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
configs/z80sim and xtrs: Serial driver lower halfs ioctl methods should return a negated errno value, not set the errno variable.
drivers/wireless: CC1101 driver not permitted to set errno.
drivers/sensors: LIS331DL driver not permitted to set errno.
drivers/lcd: ILI9341 initialize method not permitted to set errno,
drivers/serial: 16550 UART driver IOCTL method must not set errno; it must return a negated errno value.
drivers/xbee: Fixes a few warnings
* drivers/xbee: Fixes a few warnings
* configs/clicker2-stm32: Updates sections about i8sak usage in the README
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/wireless: Adds XBee S2C (802.15.4 firmware) support. XBee driver emulates mac802154 interface
* drivers/wireless/xbee: Adds xbee_netdev. Very similar to mac802154_netdev
* configs/same70-xplained: Starts adding support for XBee radio
* drivers/wireless/ieee802154/xbee: More structuring of XBee driver
* drivers/wireless/ieee802154/xbee: More Xbee work. Starts adding support on Clicker2
* drivers/wireless/ieee802154/xbee: More XBee MAC code
* configs/clicker2-stm32: More work to add XBee radio support
* drivers/wireless/ieee802154/xbee: Most of driver is now structured. No build errors
* configs/clicker2-stm32: Adjustments to XBee click module support
* drivers/xbee: Changes md_ prefix to xd_ prefix for xbeenet_driver_s fields
* drivers/xbee: XBee network device now passes MAC events via IOCTL
* drivers/xbee: Support querying device for parameters, setting parameters, and structures association/startpan logic
* configs/clicker2-stm32: Fixes Xbee lower half ATTN poll logic
* drivers/xbee: Removes dependce on CONFIG_IEEE802154_NETDEV
* drivers/xbee: Supports MAC RESET.request primitive
* drivers/xbee: Exposes generic AT query to the rest of driver
* drivers/xbee: Sets local values when writing setting change to Xbee device
* drivers/xbee: Finish association logic
* drivers/xbee: Adds xbee_get_mhrlen( ) allocating enough space for API frame header to frame
* drivers/xbee: Finishes transmit/receive logic
* drivers/xbee: Fixes xbee_netdev to match logic in mac802154_netdev.c
* drivers/xbee: Rearranges logic to prevent a loop condition where recursion could potentially occur to the point of deadlocking the system
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Merged in merlin17/nuttx/mac802154-sock (pull request #479)
wireless/ieee802154: Adds support for receiving MAC events via IOCTL through socket interface. Other small fixes and cleanup
* ioctl: Cleans up MAC802154IOC values
* wireless/ieee802154: Cleans up MAC802154IOC_NOTIFY_REGISTER logic in character driver
* wireless/ieee802154/mac802154_netdev: Adds support for MAC event notification via IOCTL
* wireless/ieee802154/mac802154: Changes reset logic. No longer reset extended address.
* wireless/ieee802154: Cleans up MAC802154IOC logic
Moves MAC802154IOC from ieee802154_ioctl.h and renames ieee802154_ioctl.h to ieee802154_device.h since it only contains types relevant to the MAC char device now.
* wireless/ieee802154/mac802154_device: Cleans up IOCTL logic for recent changes.
* drivers/wireless/ieee802154/mrf24j40: Adds missing break in case statement
* wireless/ieee802154/mac802154_netdev: Starts adding support for passing MAC events via IOCTL
* wireless/ieee802154/mac802154: Fixes issue with receiver enable logic
* wireless/ieee802154/mac802154: Fixes issue where extended address is cleared and not rewritten after radio reset
* configs/clicker2-stm32/mrf24j40-mac: Enables RAMLOG and wireless driver logging
* wireless/ieee802154/mac802154: Fixes poll logic meant to automatically choose address mode based on short address range.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
commit 2a3ab1652a2c95bcfc8be8380fc7cbdcb6472938
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sat Aug 19 08:44:31 2017 -0600
PF_IEEE802154: Finish some missing bind() logic. Add configs/sim configuration for testing.
commit 59be4b846a6e3bfe82087a888e3fdac9c3c414e5
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 19:30:04 2017 -0600
PF_IEEE802154: More renaming to decouple 6LoPAN from radios in general.
commit 69fabb1aea76e54381bdc13de28a3f1441fb42f4
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 19:21:11 2017 -0600
PF_IEEE802154: Missed a few renamings.
commit ff0af1bb25567720934cc1c2a721ccd92cc35f89
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 17:46:58 2017 -0600
PF_IEEE802154: A few bugfixes
commit 01c7c84afd00cf907d280d30cfaf0fb2cf90e02e
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 17:01:31 2017 -0600
PF_IEEE802154: A few bugfixes
commit dcef4056d1c1488c93151135f3b7106977faa903
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 16:31:05 2017 -0600
PF_IEEE802154: Bring in framework for sendto/recvfrom. Currently just a crude port of functions from net/pkt and do not provide the implemenation needed.
commit 68c5b7b6dd3ab7eb2d0c19890abb38e6561b140e
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 15:18:31 2017 -0600
Trivial fix to typo in comment
commit fd0af534c089569ccdbd59f13b85453de0a653ad
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 15:07:20 2017 -0600
PF_IEEE802154: Add device lookup logic; Rename some things that used to be used only by 6LoWPAN but now must be shared with PF_IEEE802154 and need more generic naming.
commit 4fc80a1659f1c699b050775cefc7f6b631b46114
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 13:49:54 2017 -0600
PF_IEEE802154: Add driver poll logic.
commit d83f71992df8764faa93f9425f1a7602a758f730
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 13:28:59 2017 -0600
PF_IEEE802154: Add frame input function.
commit 77561b8c4d5d7be1f8d8eb62cf1a07229afe2048
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 12:46:29 2017 -0600
PF_IEEE802154: Socket type should be SOCK_DGRAM. Hook in socket interface.
commit c0f90350282e9905d7f26a1b30f04cc6d6794648
Merge: 8b518abfd0 169c55e546
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 09:36:32 2017 -0600
Merge remote-tracking branch 'origin/master' into pf_ieee802154
commit 8b518abfd07d492f5148f2c5fdf65604de9822da
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 09:35:39 2017 -0600
PF_IEEE802154: Add initialization and connection management logic.
commit 98b62620b3cb420041d8ad14204f9410a8aace8c
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 07:52:51 2017 -0600
PF_IEEE802154: Add basic build support and socket interface framework.
