Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files modified in this PR through nxstyle and correct all coding standard problems.
Xiang Xiao <xiaoxiang@xiaomi.com>
Remove TIME_EXTENDED option to more conform C standard
Note: the code/data size increment is small
to fix the follow error:
Refresh skp16c26/ostest
LN: include/arch/board to /workspace/mirtos/nuttx/boards/renesas/m32262f8/skp16c26/include
LN: include/arch/chip to arch/renesas/include/m32262f8
Author: Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files in last PR through tools/nxstyle and correct all coding standard complaints.
Author: Oleg <ev.mipt@gmail.com>
* Fix CAN driver to work with internal OS interfaces. Store internal file pointer in f_priv and use it then to distinct readers (See issue #111)
* Store reader pointer in f_priv instead of filep
* Don't need in filep in can_reader_s
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on .c and .h files and fix it
Author: Alin Jerpelea <alin.jerpelea@sony.com>
drivers: usbdev: minor fix
drivers: usbdev: usbmsc full speed not available
Change transfer size to be based on maxpacket size.
drivers: usbdev: Fix string ID calculation
For *_STRBASE defines, it already unnecessary because composite device setup
has been changed, it would be calculated by *_composite.c in board sources.
drivers: usbdev: Fix invalid/unsupported command processing
Mass Storage Class shall stall when invalid or unsupported commands
has been recieved.
drivers: usbdev: Remove unnecessary reset logic
drivers: usbdev: Flags comparison fix
drivers: usbdev: Descriptor type mismatch fix when dual speed is enabled
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle against .c .h files and fix it
Author: Adam Feuer <adam@starcat.io>
Summary
Adds CDC ECM Ethernet over USB High Speed for SAMA5D36-Xplained
(and maybe other boards) (most of the code was there already,
but didn't work out of the box for the SAMA5D36-Xplained)
Only SAMA5D36-Xplained has been tested so far
Impact
None if you don't use the CDC ECM Ethernet driver
On SAMA5D36-Xplained, this adds high-speed Internet connectivity
over USB 2.0 High Speed. via the USB CDC ECM Gadget driver.
It may work on other boards too.
This also fixed full-speed (low-speed) mode for the board too.
Limitations
Hasn't been tested on anything other than SAMA5D36-Xplained board.
TODO
Ideally this would include a composite RNDIS device so it would
also work seamlessly on Windows. That is for a future PR
Ideally this would include software to help configuration via
mDNS/DNS-SD for plug and play compatibility with Linux and macOS.
That is for a future PR.
Detail
Only a few lines of C driver code needed to be changed, since the
capability was there already. The rest is config and documentation.
Changes the SAMA5D3-Xplained board bringup to match the SAMA5D3-EK
board bringup
A helper script to configure Linux routing and iptables NAT is also
provided, along with documentation on how to use it.
Testing
Manual, on a Ubuntu Linux 19.10 system and MacOS 10.14.6 Mojave
MacBook Pro.
How To Verify
Follow the new CDC ECM Ethernet over USB instructions in the board
README.txt file
Commits:
remove non-UTF-8 chars in comment and reformat
removed unneeded comment markers
instructions for using the defconfigs
removed EMAC from config
- to prove this example only needs the CDC ECM Ethernet over USB to work
added CDC-ECM Ethernet over USB info to README
added U-Boot image
added netusb helper script
- this can configure the Linux network interface and routes
so you can ping or access the NuttX system via TCP/IP.
renamed defconfig dirs to be ethernet-over-usb
- was usb-over-ethernet which is not right
added USB DMA to defconfigs
updated readme with autoboot and debugging info
bringing ethernet-over-usb examples into parity
added cdc ecm ethernet over usb with telnetd config
added defconfig
only use phy interrupt if netdevices is ethernet
- because now netdevice could be CDC ECM ethernet over usb
which has no PHY interrupt
add bringup to Makefile
add bringup
app init cleanup
init cdc ecm driver and rndis driver; some cleanup
fixed some typos and odd characters
usb over ethernet working over usb 2.0 hs
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on all .c and .h and fix all issues
Author: Alin Jerpelea <alin.jerpelea@sony.com>
drivers: mtd: smart: Add smartfs fsck feature
Support fsck to check and repair the smartfs file system. If the power
loss occurs during writing into the flash, the dead space are created
in flash after the next power cycle. To avoid this problem, introduce
fsck and keep the consistency of file system in initializing smartfs.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
commit 60927c5fb6a353994341601f55071c618e97682b
Author: Alin Jerpelea <alin.jerpelea@sony.com>
Date: Thu Dec 28 18:27:21 2017 +0900
drivers: mtd: smart: Fix duplicate sector selection in SmartFS
Add care for 16-bit sequence without CRC.
drivers: mtd: smart: Check CRC of duplicate sectors
In the illegal case by power-loss, when the multiple logical sectors are
duplicated, we compare the sequence number of each sector and select the newer
sector. Just in case, add CRC check for the newer sector. If the newer sector
has CRC error, then we use the older sector.
drivers: mtd: smart: SPI-Flash recovery from the initial error state
The FLASH may be not erased in the initial delivery state.
Just in case for the recovery of this fatal situation,
after once erasing the sector, return the sector as a free sector.
drivers: mtd: smart: Fix error handling in smartfs mtd driver
Add error handling in relocate sector.
drivers: mtd: smart: Fix initialize sector sequence value in smartfs
Fix initialization of sequence value into sector header and also avoid
unaligned memory access when CONFIG_MTD_SMART_ENABLE_CRC=n.
drivers: mtd: smart: Fix handling of duplicate sector in smartfs
In smartfs scan, if duplicate logical sector is found on the device,
then smartfs selects the winner sector by comparing sequence number,
and the loser sector is soon released. Fix a bug this loser sector
is registered into logical-to-physical sector mapping table.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle to check .c and .h files and fix reported issues
Author: liuzhao <happypapa@yeah.net>
Add Quectel EC20 4G LTE Module USB CDC/ACM support
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix stm32l4_otgfshost.c: error: 'ret' undeclared (#32)
result by commit 6a3c2aded6
Change-Id: I68ba79417d8da102da8d91c74496961aef242dd9
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
wireless/bluetooth/bt_null.c:274:10: warning: implicit declaration of function 'bt_driver_register'; did you mean 'bt_netdev_register'? [-Wimplicit-function-declaration]
return bt_driver_register(&g_bt_null);
sim_bringup.c:324:9: error: too few arguments to function 'bt_netdev_register'
ret = bt_netdev_register();
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Ran nxstyle against many of the affected files. But this job was too big for today. Many of the network drivers under arch are highly non-compiant and generate many, many faults from nxstyle. Those will have to be visited again another day.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
This effects all network drivers as well as timing related portions of net/: devif_poll_tcp_timer shouldn't be skipped in the multiple card case. devif_timer will be called multiple time in one period if the multiple card exist, the elapsed time calculated for the first callback is right, but the flowing callback in the same period is wrong(very short) because the global variable g_polltimer is used in the calculation. So let's pass the delay time to devif_timer and remove g_polltimer.
Driver update
* drivers/mtd/Make.defs: Add MTD driver for QuadSPI-based Winbond NOR FLASH
* stm32l4/stm32l4_qspi.c: the "QSPI_DMA_PRIO" has been defined above
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Misc changes made following recommendatinos of tools/nxstyle.
Author: kyChu <hello.kychu@gmail.com>
drivers/mtd/w25qxxxjv.c: Add QSPI-based Winbond NOR FLASH driver
drivers/mtd/Kconfig: include w25qxxxjv mtd driver to menuconfig
mtd/mtd.h: add function prototype of w25qxxxjv_initialize
We also make an attempt to avoid the thundering herd problem if there are multiple readers/pollers.
Patch also removes forcing CONFIG_RAMLOG_CRLF in nuttx/syslog/ramlog.h as there is no point of wasting precious RAM for useless characters.
