current implementation incorrectly update CURRENT_REGS to interrupt context if
trigger nested interrupt, (e.g, hard fault occurs during interrupt handling)
this would ambiguous for programs using CURRENT_REGS, this patch will prohibit
the update of CURRENT_REGS on nested interrupt handling
Signed-off-by: chao.an <anchao@xiaomi.com>
and removed two tcp_send_txnotify() calls from tcp_sendfile (they are not needed anymore).
As a result, the TX throughput of both the tcp_send_buffered and tcp_send_unbuffered
is significantly boosted in case of TUN/TAP network device.
The image must be placed into:
boards/risc-v/mpfs/icicle/include/boot_romfsimg.h
The image is mounted by mpfs_bringup, which is run by the application
itself, or by board_late_initialize() in the case when
CONFIG_BOARD_LATE_INITIALIZE is defined, e.g. with CONFIG_BUILD_KERNEL
- Add test for mode support, which is architecture dependent
- Add tests for address alignment and region size
- Add option to query for access rights
- The function goes through every PMP entry and tests if an address
range from [base, base+size] has been configured for desired
access rights.
- If several PMP entries match the range and access rights, the
information is combined
- End result is either no access, a partial match was found, or a full
match was found. Details about the partial match are not provided.
The intent for testing access rights and not just blindly applying them
is a case where they are already set in e.g. a bootloader. In this
case, nothing should be done, unless the configuration does not match,
in which case the software must not continue further.
NOTE: THIS ONLY WORKS WHEN KERNEL RUNS IN M-MODE FOR NOW
This frees the PMP for other use, e.g. HART memory separation.
The page tables are statically allocated, 1 per level.
This feature is now behind CONFIG_MPFS_USE_MMU_AS_MPU, because
only the MPFS target supports this (others are not tested).
If the MMU is used for memory separation within a HART, the PMP must
still be configured to allow user access to the memory mapped for the
HART, because PMP *rekoves* access by default. At this point all of
the user memory as well as the kernel RAM are opened.
A more flexible solution for PMP configuration will follow.
The old implementation used the default ld.script for the kernel side
which did not obey the memory.ld limits whatsoever.
Also, provide the user space addresses from the linker script to get rid
of the pre-processor macros that define (incorrect) default values for
the user space composition.
Summary:
- I noticed that make export does not work with swama5d4-ek:knsh
- This commit fixes this issue.
- NOTE: apps/Makefile also needs to be updated.
Impact:
- CONFIG_BUILD_KERNEL=y only
Testing:
- Build (make and make export) with sama5d4-ek:knsh
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
- remove some unneeded includes
- tab/space fixes
- change DEBUGPANIC to PANIC in noreturn function, otherwise it compiles only in DEBUG builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The following options need to be taken in account while determining
the proper hart_index2id -table:
CONFIG_MPFS_HART1_SBI
CONFIG_MPFS_HART1_SBI
CONFIG_MPFS_HART3_SBI
CONFIG_MPFS_HART4_SBI
Unused harts should be marked with -1. Hart0 is never used so it
stays at -1.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Commit 5d1a444812 replaced __attribute__
((unused)) with unused_code but two instances of __attribute__ ((used))
were also incorrectly replaced. Add used_code/used_data and used them
instead.
Some toolchains may be built without libm support, but using
such toochain should not generate any errors in case if math
functions are not used in the program
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Add two config flags for each hart for a bootloader nuttx:
CONFIG_MPFS_HARTx_SBI :
- select whether the hart boots via opensbi or not.
CONFIG_MPFS_HARTx_ENTRYPOINT :
- the target address to jump to, either directly from startup code or
from SBI if CONFIG_MPFS_HARTx_SBI is set
This allows building a nuttx based bootloader application, which can load
different applications/OSs for individual harts and jump to those
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Hart index to hart id table is used to track unused and used harts. This
table is useful when configuring only some of the harts for OpenSBI use.
Mpfs will always have the hart0 unused, so mark it with -1.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
- Define RV_MMU_PT_LEVELS as the arch max
- Add way to find the PPN from a PTE
- Make utility function to create a satp register value, instead of
combining this to mmu_enable
- Add function to read the current satp value
- Add function to write the satp register, also fix the fence instruction
Sv39 is the only mode supported for now. However, it should be trivial
to extend the driver to support the other modes (including Sv32) as well.
The driver is tested with mpfs only, but it should work with any riscv
implementation.
u-boot/kernel may use any uart, not just uart1, depending
on the device tree configuration. They will also reset the
corresponding uarts as well. It doesn't need to be done
here.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This drops the dependency to riscv_internal.h which ensures
less redefinition conflicts. OpenSBI declares some of the
variables again which are spread in many NuttX files.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
There is no such section. Instead, place the object mpfs_head.o at the start of
the text.
Put mpfs_head.o directly into the arch library; there is no need to define
it separately in HEAD_ASRC.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Add a new configuration for CONFIG_N_IRQ_STACKS, whcih defaults to
CONFIG_SMP_NCPUS or 1
- this allows configuring multiple IRQ stacks also in the case where SMP
support is not needed
- this is specifically needed in mpfs target, where "bootloader" build boots
only on one hart, but the startup code executes on all harts and handles SW IRQs
Also don't store/restore GP if RISCV_SAVE_GP is not defined. If the GP is not
stored in fork, it can't be restored for new tasks
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For Linux, we rename the section so that they are not invoked.
However, it doesn't work for macOS.
Notes:
* Renaming the sections (as the Linux version does) doesn't work
because the section is looked by its flags, not by its names.
* No convenient tools available to alter the relevant bit in
the section flags.
* The constructors are invoked before the program entry point.
As in _xtensa_syscall_handler, a3 was save and reused before
_xtensa_context_save, a3 save in _xtensa_context_save will generate
error.
Signed-off-by: zhuyanlin <zhuyanlin1@xiaomi.com>
1. error in A3 push stack
2. when interrupt stack enable, push a12 is xtensa_irq_dispatch
parameter 1, instead of sp. As sp is interrupt stack address set by
`setintstack`, not the interruptee stack address
Signed-off-by: zhuyanlin <zhuyanlin1@xiaomi.com>
includes following parts:
add support of sparc in arch/Kconfig
add support of sparc in boards/Kconfig
add sparc dir in arch, add sparc dir in boards
add support of sparc in libs/libc/machine
modify all the coding style problem about saprc
Some SoC like bl602 require the exception entry 8 byte align, it should
be safe for other chips so we can apply it globally.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
