Whenever a SPI flash operation is going to take place, it's
necessary to disable both the instruction and data cache. In order
to avoid the other CPU (if SMP is enabled) to retrieve data from
the SPI flash, it needs to be paused until the current SPI flash
operation finishes. All the code that "pauses" the other CPU (in
fact, the CPU spins until `up_cpu_resume` is called) needs to run
from the instruction RAM.
This config also prevents crashes due to the commit 6be363f, which
fix a race condition in multi-threaded write/read of the serial
driver, but increases stack size.
if multiple threads are doing serial read/write at the same time,
the driver will only wake up one of the thread, which will cause
other threads fail to be woken up in time and cause blocking
Signed-off-by: chao an <anchao@xiaomi.com>
Instead of using Espressif's emulated NVS to save Wi-Fi data, use
`wapi`s wireless configure initialization mechanism for saving
Wi-Fi data. It 1) avoids creating a specific storage partition
just to save Wi-Fi data (ESP32-C3's storage partition is used
instead); 2) avoids initialization problems of the emulated NVS
when SMP is enabled (the Wi-Fi driver tries to initialize it before
the actual partition is initialized); and 3) enables reconnecting
using `wapi reconnect` command and connect the device automatically
on bringup if `CONFIG_NETUTILS_NETINIT` is selected.
Instead of using Espressif's emulated NVS to save Wi-Fi data, use
`wapi`s wireless configure initialization mechanism for saving
Wi-Fi data. It 1) avoids creating a specific storage partition
just to save Wi-Fi data (ESP32's storage partition is used
instead); 2) avoids initialization problems of the emulated NVS
when SMP is enabled (the Wi-Fi driver tries to initialize it before
the actual partition is initialized); and 3) enables reconnecting
using `wapi reconnect` command and connect the device automatically
on bringup if `CONFIG_NETUTILS_NETINIT` is selected.
Instead of using Espressif's emulated NVS to save Wi-Fi data, use
`wapi`s wireless configure initialization mechanism for saving
Wi-Fi data. It 1) avoids creating a specific storage partition
just to save Wi-Fi data (ESP32-S3's storage partition is used
instead); 2) avoids initialization problems of the emulated NVS
when SMP is enabled (the Wi-Fi driver tries to initialize it before
the actual partition is initialized); and 3) enables reconnecting
using `wapi reconnect` command and connect the device automatically
on bringup if `CONFIG_NETUTILS_NETINIT` is selected.
ld: warning: arch_setjmp_x86_64.o: missing .note.GNU-stack section implies executable stack
ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
/usr/bin/ld: warning: nuttx.rel: requires executable stack (because the .note.GNU-stack section is executable)
The linker is instructed to make the stack non-executable with the
switch: `-z noexecstack`.
More information can be found here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ffcf9c5700e49c0aee42dcba9a12ba21338e8136
Currently only Port UART0 is supported for Allwinner A64. This PR adds support for all UART Ports: UART1 to UART4. (Except R-UART, which is a special low-power UART)
This is required for the upcoming LTE Modem Driver (Quectel EG25-G) for PINE64 PinePhone, which uses UART3. [(Details here)](https://lupyuen.github.io/articles/lte2)
The code was adapted from the NuttX UART Driver for Allwinner A1X: [`a1x_serial.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_serial.c)
`arch/arm64/src/a64/a64_serial.c`: Added ports UART1 to UART4, based on [`a1x_serial.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_serial.c)
`arch/arm64/src/a64/a64_serial.h`: Added IRQs for UART1 to UART4. Moved UART Base Addresses to `a64_memorymap.h`
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added UART Base Addresses for UART0 to UART4
`arch/arm64/src/a64/Kconfig`: Added UART1 to UART4 to Allwinner A64 Peripheral Selection menu
`boards/arm64/a64/pinephone/configs/lcd/defconfig`, `lvgl/defconfig`, `nsh/defconfig`, `sensor/defconfig`: Fixed `UART1_SERIAL_CONSOLE` to `UART0_SERIAL_CONSOLE`
This commit aims to enable the use of ROM functions on ESP32-S2.
This is done by creating the required syscall stubs table and adding the missing symbols to the linker script.
This commit aims to enable the use of ROM functions on ESP32.
This is done by creating the required syscall stubs table and adding the missing symbols to the linker script.
At present, the serial drivers qemu_serial.c and serial_pl011.c on the fvp-v8r and qemu platforms in arm64 are duplicated
and need to be merged. The plan is to place them under the drivers\serial directory to create a common code module,
so that both fvp-v8r and qemu can use the same code.
In the future, if new platforms use pl011 serial ports, they can also be directly reused
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Summary:
Keeping this option out of depend on any common serial.
Using the option, need to implement xxx_lowputc.S/c.
You can also logging the booting message through rewriting
fake arm64_lowputc with other debug method (eg semihosting,
ARM debug channel etc).
Signed-off-by: qinwei1 <qinwei1@xiaomi.com>
