This prevents dma stop operations called of a completion
call back from rentering, the callback and ensures that
the call back will see the idle state.
1. Configurable mapping of virtual address to psram physical address
2. Access SPIRAM memory at high physical address through bank switching
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
Since picolibc used by clang-17 does not provide an implementation of libm,
if you want to use clang, please must specify a libm as an option.
Signed-off-by: chao an <anchao@xiaomi.com>
armv6-m/arm_dumpnvic.c: In function 'arm_dumpnvic':
armv6-m/arm_dumpnvic.c:67:13: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'uint32_t' {aka 'long unsigned int'} [-Wformat=]
67 | _info(" IPR%d: %08x IPR%d: %08x IPR%d: %08x IPR%d: %08x\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
armv6-m/arm_dumpnvic.c:67:27: note: format string is defined here
67 | _info(" IPR%d: %08x IPR%d: %08x IPR%d: %08x IPR%d: %08x\n",
| ~~~^
| |
| unsigned int
| %08lx
Signed-off-by: chao an <anchao@xiaomi.com>
chip/stm32_ethernet.c:2014:7: warning: variable 'i' set but not used [-Wunused-but-set-variable]
2014 | int i;
| ^
1 warning generated.
Signed-off-by: chao an <anchao@xiaomi.com>
To avoid losing the first frame, the set_buf needs to excute first. At the same time, imgdata->start_capture should excuted before the imgsensor->start_capture.
Signed-off-by: yaojingwei <yaojingwei@xiaomi.com>
The divider should be rounded to the next full integer to ensure that
the resulting SPI frequency is <= target frequency, i.e. the SPI is
not overclocked.
After this, RISC-V fully supports the kmap interface.
Due to the current design limitations of having only a single L2 table
per process, the kernel kmap area cannot be mapped via any user page
directory, as they do not contain the page tables to address that range.
So a "kernel address environment" is added, which can do the mapping. The
mapping is reflected to every process as only the root page directory (L1)
is copied to users, which means every change to L2 / L3 tables will be
seen by every user.
Replace DEBUGASSERTs with sanity checks. DEBUGASSERT()s are
not necessarily enabled at all, thus risking the functionality
especially in that case. Remove PANICs as well.
Don't enable the ihc irq too early. If enabled, and the master
is already up, the irq is being issued so that the system gets
stuck or is severely slowed down. Master may be already up if
this NuttX hart only is rebooted, for example.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
When setting the essid that contains the special characters (\"'),
we need to add an escape (\) for them.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
Version 1.3.1 is the latest tagged version as of November
the 21st, 2023. This patch prepares the required changes
to make v1.3.1 work.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Adds support for hardware timestamping of received Ethernet packets.
The timestamp is available to applications using socket option SO_TIMESTAMP.
Optionally, the Ethernet PTP timer can be used as system high-resolution RTC.
In this mode it supports fine resolution rate adjustment.
Alternatively other time source for CLOCK_REALTIME can be used, and the
PTP timestamps are converted by sampling the clocks and computing the
difference. This results in a few microseconds of uncertainty.
The halt operation may be causes the raw epread data segment lost, and
usb ep_queue can handle when the usb buffer is full. so remove the
relevant operations.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Summary:
- Temporarily disables ARCH_HAVE_FORK for arm64 to address a crash issue,
as detailed in https://github.com/apache/nuttx/pull/9755.
- This is a precautionary measure until a more permanent solution is implemented.
Impact:
- Temporarily limits certain functionalities on arm64,
but necessary to ensure system stability.
Testing:
- Successfully tested on QEMU-8.1.2.
- Note: please apply the changes from https://github.com/apache/nuttx-apps/pull/1962.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
1. If CONFIG_ESP32S3_PHY_INIT_DATA_IN_PARTITION and CONFIG_ESP32S3_SUPPORT_MULTIPLE_PHY_INIT_DATA are enabled,
PHY initialization data (PHY initialization data is used for RF calibration) will be loaded from a partition.
2. The corresponding PHY init data type can be automatically switched according to the country code,
China's PHY init data bin is used by default, country code can be modified through the wapi command: wapi country <ifname> <country code>.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
If using flow control with a high CTS the thread may be
blocked forever on the second transmit attempt due to waiting
on the txdma semaphore. The calling thread can then never
make progress and release any resources it has taken, thus
may cause a deadlock in other parts of the system.
The implementation differs in behavior from interrupt-driven
TX. It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to
do next.
If using flow control with a high CTS the thread may be
blocked forever on the second transmit attempt due to waiting
on the txdma semaphore. The calling thread can then never
make progress and release any resources it has taken, thus
may cause a deadlock in other parts of the system.
The implementation differs in behavior from interrupt-driven
TX. It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to
do next.
If using flow control with a high CTS the thread may be
blocked forever on the second transmit attempt due to waiting
on the txdma semaphore. The calling thread can then never
make progress and release any resources it has taken, thus
may cause a deadlock in other parts of the system.
The implementation differs in behavior from interrupt-driven
TX. It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to
do next.
This commit sets the BLE's interrupt as a IRAM-enabled interrupt,
which enables it to run during a SPI flash operation. This enables
us to create a cache to off-load semaphores and message queues
operations and treat them when the SPI flash operation is finished.
By doing that, we avoid packet losses during a SPI flash operation.
This commit provides an interface to register ISRs that run from
IRAM and keeps track of the non-IRAM interrupts. It enables, for
instance, to avoid disabling all the interrupts during a SPI flash
operation: IRAM-enabled ISRs are, then, able to run during these
operations.
It also makes the code look more similar to the ESP32-S3 SPI flash
implementation by creating a common `esp32_spiflash_init` that is
responsible to create the SPI flash operation tasks. The function
intended to initialize the SPI flash partions was, then, renamed to
`board_spiflash_init`.
Whenever we enter/leave a critical section, the interrupt status is
saved and, then, restored. However, for the ESP32's BLE adapter,
entering/leaving a critical section is done on separate functions
that need to be registered as a callback.
The status flag was being saved as a global variable. However,
calling nested enter_critical_section would overwrite this global
variable that was storing the previous flag and, when leaving the
last critical section, the restored status would be different from
the one expected. The proposed solution for this issue is to create
a global array to store the interrupt status flags for nested calls.
If using flow control with a high CTS the thread may be blocked forever
on the second transmit attempt due to waiting on the txdma semaphore.
The calling thread can then never make progress and release any
resources it has taken, thus may cause a deadlock in other parts of the
system.
The implementation differs in behavior from interrupt-driven TX and the
STM32F7 TXDMA . It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to do next.
Some APIs are implemented both in common code and CHIP-specific code,
and the link needs to be based on the implementation in CHIP, so move
NUTTX_CHIP_ABS_DIR before common src.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Because there is no pre-encoding length of the ssid, the ssid including
the Chinese characters whose length is less than 32 after encoding
cann't be translated.
For example, the ssid name is `word人`. After encoding it is `world\xe4\xba\xba` and will not be decoded.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
These flags are not used in the code.
SERIAL_HAVE_RXDMA and SERIAL_HAVE_TXDMA flags are used instead.
STM32_UART_TXDMA flag is not even defined in Kconfig
Connecting the static page tables to each other was done with the page
table virtual address (riscv_pgvaddr) when the page table physical address
is needed.
I can never remember whether the static page table list contains the
table's physical or kernel virtual address.. Add the fact as a comment
there.
Also add the limitations that come from this static page table approach
for Sv32.
The SSID can be configured with special symbols suach as single
quotations, double quotations and backslashes, which need to be escaped.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
This adds option to do PMP configuration via mpfs_board_pmp_setup instead
of just opening up everything. In this case, it is up to the specific
board to implement the PMP configuration in whichever way it sees fit.
With TCD set to loop, there is a window where the
DMA has raised Done, but not reloaded the TCD, resetting
count and clearing Done.
In this window imxrt_dmach_getcount could then return 0.
Resulting in imxrt_dma_nextrx returning RXDMA_BUFFER_SIZE.
Which is not a valid index in the FIFO.
Since the count will be set to RXDMA_BUFFER_SIZE. When the DMA
engine completes the TCD reload. The imxrt_dma_nextrx would
return 0. Therefore:
(RXDMA_BUFFER_SIZE - dmaresidual) % RXDMA_BUFFER_SIZE
accomplishes this.
With TCD set to loop, there is a window where the
DMA has raised Done, but not reloaded the TCD, resetting
count and clearing Done.
In this window imxrt_dmach_getcount could then return 0.
Resulting in imxrt_dma_nextrx returning RXDMA_BUFFER_SIZE.
Which is not a valid index in the FIFO.
Since the count will be set to RXDMA_BUFFER_SIZE. When the DMA
engine completes the TCD reload. The imxrt_dma_nextrx would
return 0. Therefore:
(RXDMA_BUFFER_SIZE - dmaresidual) % RXDMA_BUFFER_SIZE
accomplishes this.
