net/netlink/netlink_route.c: Add Netlink socket NETLINK_ROUTE support for getting a snopshot of the Neighbor table.
net/neighbor/neighbor_snapshot.c: Add neighbor_snapshot() that will eventually be used by the Netlink sockets. Also fixed naming violation 'struct neighbor_entry' -> 'struct neighbor_entry_s'.
include/nuttx/net/neighbor.h: Expose format of the IPv6 neighbor table for use with Netlink sockets.
1) The change of commit ed9fe70024 left some dangling logic and incorrect, confusing comments. Prior to that commit the 'pstate' variable was non-NULL only when doing a lingering close. Comments to this effect as well as tests of pstate should also have been updated. These are confusing and inappropriate, but do not lead to incorrect behavior.
2) Eliminate an incomplete test when a disconnection event. When a disconnection event occurs, the close logic MUST always terminate the wait. The conditional test was not incorrect, however, it lacked 'else' logic and would simply ignore that disconnection event in some cases. That is bad because there may not be another disconnection event and that can lead to hangs (or at least very, very long delays).
1. For buffered tcp/udp case, if CONFIG_NET_ARP_SEND/CONFIG_NET_ARP_IPIN/CONFIG_NET_ICMPv6_NEIGHBOR isn't enabled and the table doesn't contain ip<->ethaddr mapping yet, the logic will skip the realtransmission and then arp/neighbor can't steal the final buffer to generate arp/icmpv6 packet.
2.for all other case, the tcp layer or user program should already contain the retransmit logic, the check is redundancy and may generate many duplicated packets if arp/icmpv6 response is too slow because the cursor stop forward. If user still concern about the very first packet lost, he could fix the issue by enabling CONFIG_NET_ARP_SEND/CONFIG_NET_ICMPv6_NEIGHBOR at begin.
drivers/ieee802154/xbee: Add configuration option for setting the default prefix to use when bringing up the network and setting the IP address.
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee_netdev.c
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Iobinstrumentation
* mm/iob: Introduces producer/consumer id to every iob call. This is so that the calls can be instrumented to monitor the IOB resources.
* iob instrumentation - Merges producer/consumer enumeration for simpler IOB user.
* fs/procfs: Starts adding support for /proc/iobinfo
* fs/procfs: Finishes first pass of simple IOB user stastics and /proc/iobinfo entry
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ieee802154/sixlowpan: Removes unnecessary conversions that were happening due to a misunderstanding of byte ordering with EUI-64
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee_netdev.c
Approved-by: Gregory Nutt <gnutt@nuttx.org>
net/ipforward: Check if interface is up early on when forwarding to avoid extra work.
As noticed in a previous wireless commit, when forwarding is enabled and a packet comes in, the packet is attempted to be sent on each other netdev without regard for whether it is in the UP state. Of course this is eventually caught, but it can be caught earlier to avoid unnecessary work, especially in the 6LoWPAN case where a useless packet conversion will occur.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
net/udp: Remove net stack dependency from CONFIG_NET_BROADCAST
This change allows us to use CONFIG_NET_BROADCAST without network
stack. (i.e. usrsock application can use broadcast)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
net/: Fix some naming inconsistencies, Fix final compilation issies.
net/inet/inet_close(): Now that we have logic to drain the buffered TX data, we can implement a proper lingering close.
net/inet,tcp,udp: Add functions to wait for write buffers to drain.
net/udp: Add support for notification when the UDP write buffer becomes empty.
net/tcp: Add support for notification when the TCP write buffer becomes empty.
net/inet: Fix tcp active close in inet_close.c
In previous implementation, FIN packet was not sent when a socket
is actively closed (e.g. telnetd or webserver) without SO_LINGER.
This issue happens because the socket closing sequence waits for
the status.cl_sem only if lingering timeout is set. However,
in many server use-cases, SO_LINGER is not usually set and even
in these cases, FIN packet must be sent correctly.
This PR changes the logic in inet_close.c so that it can wait
for status.cl_sem regardless of SO_LINGER. Instead, if SO_LINGER
is set, it waits for the semaphore with timeout option.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
net/usrsock: Fix debug logs and remove DEBUGASSERT from usrsockdev_do_request()
In a client mode, socket() will be the first request for usrsockdev_do_request().
However, in a server mode, the first request to accepted sockets will be recv()
or others which depend on applications. So I think we should remove this
DEBUGASSERT from usrsockdev_do_request().
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ez80: Fixing a few more compile problems. I am afraid that the 5.3.0 compiler it too buggy to use.
ez80: Additional build-related fixed.
eZ80: Updating to use the newest ZDSII 5.3.0 toolchain.
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
sched/init/nx_start.c: Add support for CONFIG_BOARD_DRIVER_INITIALIZE. If this option is selected then nx_start() will call a board-provided function board_driver_initialize() immediately after calling up_initialize().
Rename CONFIG_BOARD_INITIALIZE to CONFIG_BOARD_LATE_INITIALIZE.
Raname board_initialize() to board_late_initialize()
Squashed commit of the following:
sched/sched/sched_getsockets.c: Fix an error in conditional compilation.
fs/: Remove all conditional logic based on CONFIG_NSOCKET_DESCRIPTORS == 0
Documentation/: Remove all references to CONFIG_NSOCKET_DESCRIPTORS == 0
include/: Remove all conditional logic based on CONFIG_NSOCKET_DESCRIPTORS == 0
libs/: Remove all conditional logic based on CONFIG_NSOCKET_DESCRIPTORS == 0
net/: Remove all conditional logic based on CONFIG_NSOCKET_DESCRIPTORS == 0
sched/: Remove all conditional logic based on CONFIG_NSOCKET_DESCRIPTORS == 0
syscall/: Remove all conditional logic based on CONFIG_NSOCKET_DESCRIPTORS == 0
tools/: Fixups for CONFIG_NSOCKET_DESCRIPTORS no longer used to disable sockets.
Squashed commit of the following:
configs/: The few configurations that formerly set CONFIG_NFILE_DESCRIPTORS=0 should not default, rather they should set the number of descriptors to 3.
fs/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
tools/: Tools updates for changes to usage of CONFIG_NFILE_DESCRIPTORS.
syscall/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
libs/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
include/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
drivers/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
Documentation/: Remove all references to CONFIG_NFILE_DESCRIPTORS == 0
binfmt/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
arch/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
net/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
sched/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
sched/Kconfig: CONFIG_NFILE_DESCRIPTORS may no longer to set to a value less than 3
configs/: Remove all settings for CONFIG_NFILE_DESCRIPTORS < 3
net/sixlowpan: Record and restore d_buf on entry/exit of sixlowpan_input. This avoids an issue where d_buf gets set to NULL by sixlowpan, and then is used by forwarding logic from another network interface before getting set back to the drivers internal b
Approved-by: GregoryN <gnutt@nuttx.org>
sixlowpan: Fixes logic surrounding the Universal/Local bit. This bit represents whether the IID is locally/globally administered. The U/L bit is bit 1 of the MSB of the EUI-64. It should only be inverted in cases where there is a full EUI-64. In cases whe
* sixlowpan: Fixes logic surrounding the Universal/Local bit. This bit represents whether the IID is locally/globally administered. The U/L bit is bit 1 of the MSB of the EUI-64. It should only be inverted in cases where there is a full EUI-64. In cases where the IID is derived from say, a short address, this bit should be forced to 0, indicating that it is locally administered.
See:
https://tools.ietf.org/html/rfc4291#section-2.5.1https://tools.ietf.org/html/rfc4944#section-6https://tools.ietf.org/html/rfc2464#section-4
* sixlowpan: Account for endianness with U/L bit.
Approved-by: GregoryN <gnutt@nuttx.org>
net/sixlowpan: Fixes decompression of ipaddr from MAC address. The logic used to populate the IP from the radio address should match sixlowpan_ipfromsaddr/sixlowpan_ipfromeaddr
Approved-by: GregoryN <gnutt@nuttx.org>
The MLD implementation did not follow the RFC correctly when it is the Querier. The Querier should use a general query and get query messages from all members of all groups. This would be driven by a single timer per sub-nset since all groups are queried at once. Instead, the design used a Multicast Address Specific Query with one timer per group and ignores groups that we are not members of.
Similary, the MLDv1 compatibility timer should be a single, separate timer, not a per-group timer.
net/mld: Group may be NULL when sending a general query
net/icmpv6/icmpv6_input.c: Correct caculation of the ICMPv6 header address
net/mld/mld_query.c: Correct back test for group found.
net/mld/mld_report.c: Fix host vs. network order problem.
net/mld/mld_send.c: Correct the address used in sending the General Query. It should be the unspecified address in that case.
net/mld: Querying workaround. The MLD implementation does not follow the RFC correct when it is the Querier. The Querier should use a general query and get query messages from all members of all groups. This would be driven by a single timer since all groups are queried at once. Instead, the design currently uses a Multicast Address Specific Query with one timer per group and ignores groups that we are not members of.
Normally it is required that the network be in the "down" state when re-configuring the network interface. This is thought not to be a necessary here because.
1. The ICMPv6 logic here runs with the network locked so there can be no outgoing packets with bad source IP addresses from any asynchronous network activity using the device being reconfigured.
2. Incoming packets depend only upon the MAC filtering. Network drivers do not use the IP address; they filter incoming packets using only the MAC address which is not being changed here.
net/mld: Fix a couple of places where I forgot to unlock the network in the previous commit.
net/mld: Implement 'Other Querier Present Timer'. This timer is used to revert to Querier mode if there is no other querier on the network. Also, fix some naming: The Done message is not just Version 1 but is used with Version 2 as well.
net/igmp: Back out some blind, backported improvements to IGMP from MLD. There are too many subtle differences in the protocols for this to be safe.
net/mld: Checksum calculation needs to know the full size of the IPv6 header, including the size of the extension headers. The payload size in the IPv64 header must include the extension headers (not considered part of the header in this case). Fixes a few additional errors in size, endian-ness and checksum calculations. Wireshark now reports the the outgoing Report has a good checksum.
net/mld/mld_query.c: Add a cast to assure that the left shift does not overflow.
net/mld: More updates from comparison with roughly leveraged code and the MDL RFCs 2710 and 3810.
net/mld: More updated from comparison with roughly leveraged code and the MDL RFCs 2710 and 3810.
net/mld: Beginning comparison with roughly leveraged code and the MDL RFCs 2710 and 3810.
include/nuttx/net/ipv6ext.h: Fix some terminology: Hop-by-hop, not Hop-to-hop or Hop2hop.
net/devif/ipv6_input.c and net/icmpv6/icmpv6_input.c: Add logic to skiip over the variable number of IPv6 extension headers that may be present between the IPv6 header and the transport layer header. The extension headers are simply ignored. This is necessary because with MLD, certain incoming messages may have, at a mimimum, a Router Alert Hop-by-hop extension header.
net/inet/ipv6_setsockopt.c: Implement the IPV6_JOIN_GROUP and IPV6_LEAVE_GROUP socket options.
net/mld: The MLD logic now compiles and is much less toxic. It still is not a proper MLD implementation: (1) It is basically a port of IGMP, tweaked to work with IPv6 and ICMPv6 MLD messages, (2) it needs a proper analysis and comparison with RFC 3810, and (3) it is completely untested. For this reason, it will remain EXPERIMENTAL for some time.
net/mld: Add some missing macros, more fixes related to IPv6 vs IPv4 types,
net/mld: More compilation cleaning. Most fixups for IPv6 vs IPv4 types.
net/mld: Hook crudely converted .c files into build system and resolve a few of the many, many compilation/design problems.
net/mld: Add support for MLD statistics.
net/mld: Hook in MLD poll and packet transmission logic.
net/mld: Change references to IPv4 definitions to IPv6 definitions; Remove mld_input() since MLD piggybacks on ICMPv6 input. Add functions to catch MLD messages dispatched by ICMPv6 input logic.
net/mld: As a starting point, copy all net/igmp/*.c files to net/mld/. and change all occurrences of igmp (or IGMP) to mld (or MLD).
net/mld: More compilation cleaning. Most fixups for IPv6 vs IPv4 types.
net/mld: Hook crudely converted .c files into build system and resolve a few of the many, many compilation/design problems.
net/mld: Add support for MLD statistics.
net/mld: Hook in MLD poll and packet transmission logic.
net/mld: Change references to IPv4 definitions to IPv6 definitions; Remove mld_input() since MLD piggybacks on ICMPv6 input. Add functions to catch MLD messages dispatched by ICMPv6 input logic.
net/mld: As a starting point, copy all net/igmp/*.c files to net/mld/. and change all occurrences of igmp (or IGMP) to mld (or MLD).
Fixes logic in ipv6_input to handle more than ff02::/16 multicast addresses. Don't forward mcast packets if scope is not appropriate
Approved-by: GregoryN <gnutt@nuttx.org>
net/sixlowpan: Fixes bug in uncompress_addr handling of odd postfix.
This affected multicast compress/uncompress since it's the only logic that used an odd postfix. The odd byte needs to be handled first, not last.
Approved-by: GregoryN <gnutt@nuttx.org>
many locations: Change occurences of open() followed by file_detach() to file_open(). Change most non-controversion calls to open() to nx_open().
fs/inode/fs_fileopen.c: Flesh out file_open() with some interim, placeholder logic.
fs/inode/fs_fileopen.c: Add a framework for a file_open() implementation (no real logic in place yet).
fs/vfs/fs_open.c: Add nx_open() which is the same as open() except that it does not create a cancellation point nor does it modify the errno variable.
sched/wqueue/kwork_notifier.c: Redesign some data structures. struct works_s must appear at the beginning of the notifier entry structure. That is because it contains the work queue indices. This solves a harfault issue.
net/tcp/tcp_netpoll.c: tcp_iob_work() needs to free the allocated argument when it is finished.
net/tcp/tcp_send_buffered.c: Extend psock_tcp_cansend() so that it also requires that at least on IOB is also avaialble.
mm/iob: iob_navail() was returning the number of free IOB chain queue entries, not the number of free IOBs. Completely misnamed.
net/tcp/tcp_netpoll.c: Add logic to receive notifications when IOBs are freed (Needs CONFIG_NET_TCP_WRITE_BUFFERS and CONFIG_IOB_NOTIFIER). At present, does nothing because the logic in in psock_tcp_cansend() does not check for the availability of IOBs. That will change.
Squashed commit of the following:
Fix up some final compile isses.
net/netdev: Convert the network down notification logic to use the new wqueue-based notification factility.
net/udp: Convert the UDP readahead notification logic to use the new wqueue-based notification factility.
net/tcp: Convert the TCP readahead notification logic to use the new wqueue-based notification factility.
mm/iob: Convert the IOB notification logic to use the new wqueue-based notification factility.
sched/wqueue: Signals are not good IPCs to support the target poll functionality for several reasons including the amount of data that can be passed with a signal and in the fact that in protected and kernel modes, user threads executing signal handlers in protected, kernel memory is problematic. Instead, convert the same logic to perform the notifications via function callback on the high priority work queue.
Squashed commit of the following:
net/tcp: Add signal notification for the case when UDP read-ahead data is buffered. This is basically of clone of the TCP notification logic with naming adapted for UDP.
net/tcp: Add signal notification for the case when TCP read-ahead data is buffered.
