* tools/Config.mk - Add empty definition POSTBUILD
* tools/Makefile.unix/win - Replace CXD56xx specific logic with $(call POSTBUILD)
* boards/arm/cxd56xx/scripts/Config.mk - Add POSTBUILD definitions with logic removed from Makefile.unix/win
* boards/arm/cxd56xx/spresense/scripts/Make.defs - Include the CXD56xx Config.mk immediately after tools/Config.mk so that the empty POSTBUILD definition will be replaced with the correct one
NOTE: There is a precedent for this approach. This is the way that other architecture-specific build options are implemented. See, for example, tools/zds/Config.mk
CONFIG_FAT_MAXFNAME is set to 255 and CONFIG_NAME_MAX is set to 765
which can support max file name including Japanese characters.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Author: Alan Carvalho de Assis <acassis@gmail.com>
Check all .c and .h against nxstyle and fix it.
Author: Alin Jerpelea <alin.jerpelea@sony.com>
fs: smartfs: Fix over capacity write
When the remaining capacity of flash is one sector, if a new root
directory is created by file open, then the root directory's chain is
broken and it causes to SmartFS filesystem crash. Once this fatal
problem occurs, it's impossible to recover even if the system reboot.
Fix it by finally update link of root directory.
fs: smartfs: Fix buffer overrun
fs: smartfs: Fix uninitialized variable warnings
fs: smartfs: Memory leak fix
boards: cxd56xx: Update spresense board.h
- Fix PMIC assignment
- Add specific pin configurations for spresense
- Remove unnecessary definitions
arch: cxd56xx: Add ITM syslog init at startup
arch: cxd56xx: Enable DMA settings dynamically
Author: Alan Carvalho de Assis <acassis@gmail.com>
Verify all .c and .h against nxstyle, fixed the Mixed cases
Author: Alin Jerpelea <alin.jerpelea@sony.com>
cxd56xx improvements (#48)
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
boards: cxd56xx: spresense: cleanup and new defconfig
* arch: cxd56xx: remove NVIC_SYSH redefinition
The NVIC_SYSH is already defined in nvicpri.h
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: configs: enable SPRESENSE_EXTENSION
Enable high current mode for the Spresense Extension board on all examples
that have SDCARD support
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: ifdef SDCARD_TXS02612
The SD Card TXS02612 port expander is hosted on the Extension board and
should not be enabled if the extension board is not prezent.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: configs: increase MQ_MAXMSGSIZE
This change is needed by the display driver on spresense platform
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: config: add lcd examples defconfig
This is a configuration for the basic nx examples
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Master
* boards: cxd56xx: spresense: add Spresense Image Processor
Enable support for accelerated format convertor, rotation and so on.
using the CXD5602 image processing accelerator.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards:cxd56xx:spresense: initalize GNSS and GEOFENCE at boot
Add the optional initialization of GNSS and GEOFENCE at boot
if the drivers are enabled
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: cxd56xx: spresense: add board_timerhook function
* boards: cxd56xx: spresense: add board_timerhook function
in preparation for SDK we muts have a weak board_timerhook function
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: usbhost: add missing endif
By accident an endif was missing.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: audio: add build barrier
The audio implementation should not be beuilt if the config
CONFIG_CXD56_AUDIO is not set.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch:arm:cxd56xx: add ge2d.h header
The header is used by imageproc.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: arm: cxd56xx: audio: add power_control and audio_tone_generator
* boards: arm: cxd56xx: audio: add power_control
Add a simeple way to control the audio power for userspace apps
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: audio: add audio_tone_generator
Add a simple way to control the audio buzzer with defined frequency
for userspace apps
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: arm: cxd56xx: different updates
* boards: cxd56xx: spresense: initialize SCU at boot
The SCU has to be initialized at bootup on spresense board because several
functions depend on it.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: add audio control definitions
Add audio control definitions for the audio implementation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: add audio defconfig
Add defconfig for the audio implementation
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Spresense smp
* arch: arm: Add ARCH_GLOBAL_IRQDISABLE to ARCH_CHIP_CXD56XX in Kconfig
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch: arm: cxd56xx: Make fpuconfg() public in cxd56_start.c
NOTE: fpuconfig() is called in both cxd56_start.c and cxd56_cpustart.c
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch: arm: cxd56xx: Add support for SMP
NOTE: To run cxd56xx in SMP mode, new boot loader which will be
released later must be used.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch: arm: cxd56xx: Add irq routing for SMP in cxd56_irq.c
NOTE: In cxd56xx, each external interrupt controller can be
accessed from a local APP_DSP (Cortex-M4F) only. This commit
supports IRQ routing for SMP by calling up_send_irqreq() in
both up_enable_irq() and up_disable_irq().
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* boards: spresense: Add smp configuration
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
cxd56xx: various fixes
* arch: arm: cxd56xx: Support to set any i2c frequency
This commit supports to be able to set the i2c frequency other than just
100 or 400 Hz.
* arch: arm: cxd56xx: Enable SD clock during access to SD card
- Improve GNSS low sensitivity with SD card inserted
- Reduce power consumption by stopping SD clock
* arch: arm: cxd56xx: Do PANIC() when cpu rx fifo is overflow
If CPU Rx FIFO is overflow, it's fatal error for system. In such a case,
this commit changes to allow the user to notice by calling PANIC() for
debuggability enhancement.
* arch: arm: cxd56xx: Fix compile error in sdhci debug code
* arch: arm: cxd56xx: Remove assertion in cpu tx queue
When CPU Tx queue is overflow, it returns -EAGAIN instead of assertion
to be able to retry.
* arch: arm: cxd56xx: Add configurations for cpu fifo elements
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Fix LPADC configuration
LPADC options defined in the same symbol name, so kconfig tool
couldn't process them correctly.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Update loader and gnssfw ver.17660
* arch: arm: cxd56xx: Fix hang-up when error interrupt occurs
Fix a problem that error interrupts are not cleared.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Fix sdhci semaphore
Fix inital value of semaphore in sdhci drive.r
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: Treat the initial value of LNA power as off
LNA is always turned power on when GNSS is started. So it is desirable
that the initial value of the LNA power is off by default.
* boards: cxd56xx: Remove initial setting of PIN_AP_CLK
PIN_AP_CLK is used as a port selector of SDIO expander on the extension
board, and is set output low in initalizing. Therefore, this pin cannot
be used for other board. To avoid this restriction, remove this initial
operation because this pin is pulled down by default on the extension
board.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: spresense: Add board initialization for isx012
Add isx012 initialization to the board and include the needed headers
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: spresense: add isx012 camera initialization and config
* boards: spresense: add isx012 camera initialization
Add the initialization for the isx012 camera sensor.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: spresense: add camera defconfig
For easy configuration add camera defconfig for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
noards: arm: cxd56xx: migrate common code
* boards: arm: cxd56xx: common: move boot to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move flash to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move I2C driver to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move uid to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move usbmsc to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56: add SPH
The SPH is used by the ASMP implementation from the SDK.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: cxd56xx: add SCU sensors (2/2)
* boards: cxd56xx: add cxd56_bh1721fvc initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bh1745nuc initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bm1383glv initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bm1422gmv initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bmi160 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bmp280 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_kx022 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_lt1pa01 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_rpr0521rs initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_sensors initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56: add Backup Log driver
The driver will be used to backup logs on crash.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: add crashlog driver
Add Crashlog driver with support for reset on crash
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: move gs2200m initialization
Move the board gs2200m initalization to the common board folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: move ili9340 initialization
Move the board ili9340 initalization to the common board folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: move lpm013m091a initialization
Move the board lpm013m091a initalization to the common board folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: typo fixes
HEADER: Updates on file location
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
