riscv updates
* arch: risc-v: Remove up_dumpstate.c because the file had been merged into up_assert.c
* boards: gapuino: Modify Makefile which conforms to NuttX standards
* boards: nr5m100-nexys4: Modify Makefile which conforms to NuttX standards
Approved-by: Gregory Nutt <gnutt@nuttx.org>
HiFive1 with qemu
* arch: risc-v: Add include/.gitignore
* arch: risc-v: Add src/.gitignore
* arch: risc-v: Remove uncommon function prototypes in include/irq.h
* arch: risc-v: Add missing symbols and function prototypes in src/common/up_internal.h
* arch: risc-v: Add src/common/up_modifyreg32.c
* arch: risc-v: Enable include Make.dep in src/Makefile
* arch: risc-v: Fix stack coloration in common/up_createstack.c
* arch: risc-v: Add common/up_puts.c
* arch: risc-v: Add common/up_checkstack.c
* arch: rv32im: Move all logics from up_dumpstate.c to up_assert.c
This change is same as other architectures like arm/src/armv7-m
* arch: Select ARCH_HAVE_STACKCHECK for RISC-V in Kconfig
* arch: risc-v: Add SiFive fe310 processor
NOTE: Currently only tested with qemu
* boards: hifive1-revb: Add SiFive hifive1-revb board
NOTE: Currently only tested with qemu
* tools: Add fe310 processor to configure.sh
Approved-by: Alan Carvalho de Assis <acassis@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
STM23L4 LPTIM PWM support with multi-channel
* arch/arm/src/stm32l4/stm32l4_pwm.c:
fixed some bugs
arch/arm/src/stm32l4/stm32l4_pwm.h:
support LPTIM PWM if PWM multi-channel is selected
Channel mode for LPTIM are not available
* arch/arm/src/stm32l4/Kconfig: add new configuration for STM32L4 LPTIM support
* arch/arm/src/stm32l4/stm32l4_pwm.c: fix warning: resetbit may be used uninitialized
Approved-by: Gregory Nutt <gnutt@nuttx.org>
I did suspect that it was just about possible that there's a use for this check (specifically, when you're changing serial the clock immediately after the character is sent) but since we're only testing that the character has left the holding register and not that it's actually been sent to line I don't think it's valid even for this case.
Driver update
* drivers/mtd/Make.defs: Add MTD driver for QuadSPI-based Winbond NOR FLASH
* stm32l4/stm32l4_qspi.c: the "QSPI_DMA_PRIO" has been defined above
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards/arm/stm32h7/stm32h747i-disco: Remove references to nucleo in the stm32h747i-disco board.
arch/arm/include/stm32h7, arch/arm/src/stm32h7, and boards/arm/stm32h7/stm32h747i-disco: Add support for the STM32H747I-DISCO board.
1) Operational issue
TC (Transmission complete) and TDRE (TX Buffer Empty) were transposed in imxrt_serial.c. The end result was that for unoptimised code everything worked fine, but optimised code got itself into a real mess and continually fired interrupts. The patch attached fixes this. This one would have been found much more quickly if this particular board had supported SWO :-/
2) Startup issue
There are a number of chip errata that apply to the 1052 first revision (A-suffix) that don't apply to the second (B-suffix). Those got me for a while and it's important to use an EVK_B_ dev board if you're suffering stability problems with this particular chip. However, even with that resolved with either optimised or unoptimised code when there is no SNVS (Battery Backup) power and the power is switched on the CPU appears to boot but gets stuck with timer interrupts not being generated. The CPU is running and it will execute linear code. I have determined this by putting an 'imxrt_lowputc('A'+irq)' into up_doirq. For the non-running case the output looks like this;
LLLL
this implies 4 0x0b interrupts have been generated, and nothing else. If I hit keys on the keyboard I get 'e' in the flow. 0x0b is the SVC instruction and is the mechanism by which NuttX handles task switching. 'e' is 0x24, which corresponds to the LPUART1 interrupt. Other than these, the system does not respond further but is happily in the idle loop. In this circumstance if you hit SW2 on the EVKB board though the logjam 'unjams' and normal service is established, output now looks like;
LLLLPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPLPP ...etc.
Where 'P' is 0x0f (the SYSTICK interrupt)....this is what _should_ be happening so; SYSTICK starts up after SW2 has been pressed.
From this point on everything works correctly and you can reboot the CPU, put new code into it or do whatever you wish, **provided power is not cycled off**. If power is cycled off then return to the top and go through the process again.
When there is SNVS power to the CPU then power can be switched on and off as you wish, and the CPU will boot correctly. This has been determined by putting 3V onto J6.
I think we are probably doing something naughty with the way we are starting the clocks to the timers. There are certainly some restrictions on imxrt clock manipulation which we have studiously avoided. I am investigating further and have some potential patches but even if I find the root cause it should not be included in 8.2 as the change could be disruptive.
https://github.com/zephyrproject-rtos/zephyr/pull/8535/commits: "The imxrt1050 is configured to use SYSTICK for the kernel timer, but SYSTICK cannot wake up the soc from low-power modes. Disable low-power modes on this soc until we have support for an alternative timer."
"This fixes k_sleep on the EVKB version of the mimxrt1050_evk board. An earlier version of the board (EVK, not EVKB), had A0 silicon which by default did not enter low-power mode on a wfi."
This patch reverts the WFI enable for further investigation post 8.2. With this patch in place together with the previous one my system is fully stable(*), just drinking a bit more power than I'd like.
This change decouples that upper activity-based logic from the lower random walk logic and allows use of other upper state detection logic (such as a custom, application-specific state machine).
