Update PLL configuration parameters to match the values provided
by the vendor.
Also remove extra call to mpfs_pll_config() as it's already called
at mpfs_clockconfig().
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This patch adds corrected implementation of FLASH memory to be used
with progmem driver for use with mtd filesystems like nxffs or smartfs.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Summary:
- I noticed that QEMU shows a high CPU load.
- This commit re-adds imx_idle.c to avoid this issue.
Impact:
- None
Testing:
- Tested with sabre-6quad:smp with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This patch implements working support for EXTI GPIO.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- change (1 << n) to (1 << (n)) in macro definition
- change 1 << X to (1 << X) in code
- fix alignment
v2 -> v3:
Suggested by: Petro Karashchenko
- I was supposed to change (1 << pin) to 1 << pin, not the other way around:)
Summary:
- I noticed that sometimes uart shows nothing on the maix-bit board.
- This commit adds a workaround to avoid such the issue
Impact:
- k210 only
Testing:
- Tested with maix-bit
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Output "X" with showprogress and make a system reset.
Silently ignoring failed training is dangerous and will cause random behaviour if DDR is used
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This patch adds new chip family, stm32wl5x. This is bare minimum
implementation of said chip. I've tested this by running nsh.
There are only two chips in this family, stm32wl55 and stm32wl54.
The only difference between them is that stm32wl55 has LORA.
stm32wl5 is dual CPU (not core!). Right now only CPU1 is implemented.
CPU0 has access to radio hardware (while CPU1 does not). Chip is
designed so that CPU0 handles radio traffic while CPU1 does the
heavy lifting with data - there is communication pipe between two
CPUs.
I plan to use nuttx on CPU1 and LORA from stm32cube on CPU0 so I
don't have implementing CPU0 right now - once we have working LORA
in nuttx this may change.
Peripherals (except for radio) are shared so it's best to focus on
CPU1 to initialize all peripherals so that CPU0 can only use them
later. There is no real benefit to implement CPU0 if we don't have
working LORA/radio support in nuttx.
In time I will be implementing more and more things from this chip.
Right now I would like this minimal implementation to be merged in
case someone wants to work on this chip as well.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
---
patch v1->v2
- fixed formatting (suggested by Alan Carvalho de Assis)
- rebased patch to master (previous patch was based on nuttx-10.2
and did not compile on master)
arch/x86/Kconfig:28:warning: choice value used outside its choice group
arch/x86/Kconfig:29:warning: defaults for choice values not supported
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
We might have a situation where an allocation will be requested before
the call to `up_initialize` is performed. For the current code, this
situation is the stack for the CPUs in SMP mode.
Beside this issue, it's natural to have the internal heap initialized
with the other heaps.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
jumping back to the assembly signal trampoline and getting into its
infinite loop.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Change pin initialization timing for camera from board power on to camera device
power on for the following purposes.
- avoid unnecessary power consumption
- Make the corresponding pins available for other uses when camera is not in use
RF and system timer interrupt are used for ble.
tlsr82_flash.c:
1. BLE will loss packets during flash operation beacause the interrupt
is disabled and the operation take too long (especially erasing,
about 100ms), so allow RF and system timer interrupt during flash
operation;
2. Add sched_lock()/sched_unlock() to avoid the task switch in ble and
system timer interrupt;
flash_boot_ble.ld:
3. Because of 1, the code executes in RF and system timer interrupt
must be in ram to avoid bus error. The sem_post() will be called and
const variable g_tasklisttable will be accessed in RF and system
timer interrupt handler;
4. To improve the performance, copy some frequently called function to
ram as well, such as: sem_take(), sched_lock(), sched_unlock(),
some lib functions, some zephyr ble functions and some tinycrypt
functions;
5. The RF and system timer interrupt handler will call some libgcc
functions, so copy all the libgcc functions to ram exclude _divdi3.o,
_udivdi3.o and _umoddi3.o;
tlsr82_serial.c
6. Make up_putc() be thread safe, add enter/leave_critical_section() in
function uart_send_byte();
tc32_doirq.c
7. Increase the RF and system timer interrupt response priority;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
since the code could map the unsupported work to the
supported one and remove select SCHED_WORKQUEUE from
Kconfig since SCHED_[L|H]PWORK already do the selection
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
As coproc_save/restore only used in context_restore/save.
Use macro instead of function.
Some register use optimize.
Unify with arm/riscv.
Signed-off-by: zhuyanlin <zhuyanlin1@xiaomi.com>
The current SAMv7 PWM driver assumes that all PWM channels should
work in sync mode, but that is a partial case of a generic PWM
driver operation.
Start SAMv7 PWM channels in async mode. The sync mode should be
implemeted either using ioctl command or via a separate Kconfig
option.
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- I noticed that rv-virt:knsh64 crashes when it executes the init.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with rv-virt:knsh64
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
1. Add vbat mode for chip internal voltage sample;
2. Add adc channel config;
3. Using DFIFO2 to get the sample value, follow telink sdk.
4. Add calibration function and config;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
The FPU register saving upon vfork entry was missing.
Also added macro that tells the actual size of an FPU reg, instead
of just having a coefficient for qfpu/no-qfpu.
- Remove most of the ifeq-conditions and replace them with variables.
- Move the -I flag for 3rd party headers to opensbi/Make.defs
This clean-up / generalization makes it much simpler to add a new SBI
implementation, without the need to add a bunch of ifeq / elif conditions
to the makefile.
Let the user pick what runs on the harts. For example, the
default configuration now supports NuttX on hart2 and Linux
kernel on harts 3 and 4. Also fix a few issues in the code.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
g_mpfs_ack_sig and g_mpfs_rx_sig are better used with
SEM_INITIALIZER(0) (signalling) rather than with
SEM_INITIALIZER(1) (mutual exclusion).
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Number of channels are now set based on enabled modules (channels) in
configuration instead of the usage of static 4.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Number of channels are now set based on enabled channels in configuration
instead of the usage of static 4.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
1 move fpu register to XCP_REGS
2 move save & restore fpu register to context_save/restore
Consistency with other archs.
Signed-off-by: zhuyanlin <zhuyanlin1@xiaomi.com>
PR#6249 was already merged without the review fixes. Provide the
fixes here on a separate patch.
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- This commit adds MMU support for qemu-rv
- Please note that mtimer is disabled for S-mode because
the mtimer needs to be accessed in M-mode
Impact:
- qemu-rv only
Testing:
- Tested with rv-virt:knsh64 (will be pushed later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This provides an example of Asymmetric Multiprocessing (AMP). The
master from Linux sends pings that this NuttX echoes back. The system
uses RPMsg from OpenAMP.
The Inter-Hart Communication module is present in the vendor's software
stack with the tag "2021.11". The software is present on github at the
polarfire-soc project. The following conditions must be met:
1. FPGA programmed with 2021.11 software
2. HSS (Vendor bootloader) with 2021.11 software
3. U-boot and Linux kernel from 2011.11 software
Currently the IHC works as a slave only on the hart number 4.
On the NuttX side, this patch uses rptun that incorporates rpmsg and
virtio. If it used only rpmsg and virtio, the future maintenance would
likely be much heavier. Using rptun also simplifies many things.
Upon success, the master side from Linux may issue an example test:
root@icicle-kit-es-amp:/opt/microchip/amp/rpmsg-pingpong# ./rpmsg-pingpong
However, the rpmsg-pingpong.c (compiled on target with gcc), may need to
be modified as seen below to match the device id:
- char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.0";
+ char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.1024";
This work uses a separate linker script. Due to a bug yet unknown to date,
a small NuttX, when loaded by the vendor HSS bootloader, will cause the
Linux kernel to hang at boot. Thus, the binary size is increased with
a section 'filler_area' whose only purpose is to increase the image size
so that the Linux kernel will boot up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Implement a generic access rights modification procedure instead
of the procedures that only do one thing (enable/disable write)
to one section (text).
1. using armv6-m arm_irq();
2. simplify the interrupt number get process;
3. To improve the performance, move common exception code to ram_code.
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
fix warning:
common/arm_createstack.c: In function 'up_create_stack':
common/arm_createstack.c:154:11: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Summary:
- Because a context switch issue still exists with FPU,
it should be enabled only if EXPERIMENTAL=y
Impact:
- None
Testing:
- Tested with ostest
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
1. add pulse count support for pwm0;
2. add more detailed config for pwm;
3. pwm configuration and start process optimize;
4. tlsr82/Kconfig format;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Summary:
- TIVA_WITH_QEMU is used to run the NuttX with QEMU
- The configuration should not depend on TIVA_ETHERNET
- This commit fixes this issue
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
_xtensa_sig_trampoline is returned to after a context switch and not called
by the usual Window call instructions (call4, call8 and call12),
thus does not need the entry instruction. Furthermore, the ENTRY instruction
in this case is messing up the backtrace as it creates an extra frame.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
to generate more information for profile feedback optimization
and remove -lgcov from STDLIBS since gcc/clang will automatically
add the profile help lirary(triggered by -fprofile-generate).
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- In case of SMP and ADDRENV, allocate the page table for each cpu
- Each cpu holds separated addrenv and MMU setting
Impact:
- armv7-a
Testing:
- sabre-6quad:smp w/ qemu
- sabre-6quad:knsh w/ qemu
- sabre-6quad:knsh_smp w/ qemu (WIP)
Signed-off-by: Oki Minabe <minabe.oki@gmail.com>
Note that pinmap.h, irq.h, fdcan.h still need to be updated with proper
register definitions for the FDCAN3 peripheral present in
STM32H7[2|3][3|5] MCUs
