Commit Graph

22 Commits

Author SHA1 Message Date
Alin Jerpelea
3e45517599 Fix buffer overrun and memory leak on smartfs and improvement to cxd56xx
Author: Alan Carvalho de Assis <acassis@gmail.com>

    Check all .c and .h against nxstyle and fix it.

Author: Alin Jerpelea <alin.jerpelea@sony.com>

    fs: smartfs: Fix over capacity write

    When the remaining capacity of flash is one sector, if a new root
    directory is created by file open, then the root directory's chain is
    broken and it causes to SmartFS filesystem crash. Once this fatal
    problem occurs, it's impossible to recover even if the system reboot.
    Fix it by finally update link of root directory.

    fs: smartfs: Fix buffer overrun

    fs: smartfs: Fix uninitialized variable warnings

    fs: smartfs: Memory leak fix

    boards: cxd56xx: Update spresense board.h

    - Fix PMIC assignment
    - Add specific pin configurations for spresense
    - Remove unnecessary definitions

    arch: cxd56xx: Add ITM syslog init at startup

    arch: cxd56xx: Enable DMA settings dynamically
2020-01-08 07:51:11 -03:00
Masayuki Ishikawa
4c53f0d232 Merged in masayuki2009/nuttx.nuttx/spresense_smp (pull request #1041)
Spresense smp

* arch: arm: Add ARCH_GLOBAL_IRQDISABLE to ARCH_CHIP_CXD56XX in Kconfig

    Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>

* arch: arm: cxd56xx: Make fpuconfg() public in cxd56_start.c

    NOTE: fpuconfig() is called in both cxd56_start.c and cxd56_cpustart.c

    Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>

* arch: arm: cxd56xx: Add support for SMP

    NOTE: To run cxd56xx in SMP mode, new boot loader which will be
    released later must be used.

    Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>

* arch: arm: cxd56xx: Add irq routing for SMP in cxd56_irq.c

    NOTE: In cxd56xx, each external interrupt controller can be
    accessed from a local APP_DSP (Cortex-M4F) only. This commit
    supports IRQ routing for SMP by calling up_send_irqreq() in
    both up_enable_irq() and up_disable_irq().

    Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>

* boards: spresense: Add smp configuration

    Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-10-03 13:06:21 +00:00
Alin Jerpelea
3806a01c5d Merged in alinjerpelea/nuttx (pull request #1024)
noards: arm: cxd56xx: migrate common code

* boards: arm: cxd56xx: common: move boot to common

    This is a common function and can be reused by all boards.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: common: move flash to common

    This is a common function and can be reused by all boards.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: common: move I2C driver to common

    This is a common function and can be reused by all boards.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: common: move uid to common

    This is a common function and can be reused by all boards.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: common: move usbmsc to common

    This is a common function and can be reused by all boards.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56: add SPH

    The SPH is used by the ASMP implementation from the SDK.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-08-26 14:29:55 +00:00
Alin Jerpelea
6ecee7e403 Merged in alinjerpelea/nuttx (pull request #1021)
boards: cxd56xx: add SCU sensors (2/2)

* boards: cxd56xx: add cxd56_bh1721fvc initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_bh1745nuc initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_bm1383glv initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_bm1422gmv initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_bmi160 initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_bmp280 initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_kx022 initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_lt1pa01 initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_rpr0521rs initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: cxd56xx: add cxd56_sensors initialization

    We are adding the sensor initialization for cxd56xx boards in the
    common board folder.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56: add Backup Log driver

    The driver will be used to backup logs on crash.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: common: add crashlog driver

    Add Crashlog driver with support for reset on crash

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: move gs2200m initialization

    Move the board gs2200m initalization to the common board folder

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: move ili9340 initialization

    Move the board ili9340 initalization to the common board folder

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: move lpm013m091a initialization

    Move the board lpm013m091a initalization to the common board folder

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* boards: arm: cxd56xx: common: typo fixes

    HEADER: Updates on file location
    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-08-23 13:28:35 +00:00
David S. Alessio
ced0dc1e16 arch/arm/src/armv7-m: Add ARMv7-M setjmp/longjump functions. 2019-08-06 15:59:19 -06:00
Alin Jerpelea
5867fdc0e1 Merged in alinjerpelea/nuttx (pull request #948)
arch: arm: cxd56xx: add GNSS device and UART0

* arch: arm: cxd56xx: add GNSS device

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add Geofence Support

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add UART0 iterface

    UART0 is an interface with hardware flow control in the application subsystem.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: path correction

    In the initial commit the path reference was not updated

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-07-12 11:29:22 +00:00
Alin Jerpelea
9b8c4a355d Merged in alinjerpelea/nuttx (pull request #935)
drivers: video: add ISX012 Image sensor

* arch: arm: src: cxd56xx: add cisif support

    add cisif support on cxd56xx chip to be able to use cameras

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* drivers: video: add ISX012 Image sensor

    add driver for ISX012 Image sensor

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-07-04 14:02:05 +00:00
Alin Jerpelea
55a4029885 Merged in alinjerpelea/nuttx (pull request #928)
configs: spresense: add basic LCD configuration

* arch: arm: cxd56xx: add Graphics Engine

    Add driver for hardware image processor device

    to enable the hardware image processor set CXD56_GE2D=true

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* drivers: lcd: add ILI9340 LCD Single Chip Driver

    LCD Single Chip Driver, ILI9340, ILI Technology Corp.

    Required LCD driver settings:
    LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
    LCD_MAXPOWER should be 1:  0=off, 1=on

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* drivers: lcd: JDI LPM013M091A LCD Driver

    JDI LPM013M091A LCD Driver.

    This driver doesn't support reading data.
    Recommended to use DMA to transfer data or displayed image would be
    broken.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: add basic LCD configuration

    add basic LCD configuration for spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: add lpm013m091a LCD

    add device configuration for lpm013m091a LCD on spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: add ili9340 LCD

    add device configuration for ili9340 LCD on spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: add defconfig with LCD

    add defconfig with LCD for spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-07-03 12:24:13 +00:00
Alin Jerpelea
b922c2748e Merged in alinjerpelea/nuttx (pull request #920)
arch: src: cxd56xx: add EMMC suport

add EMMC suport for cxd56xx chip

Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-27 12:08:18 +00:00
Alin Jerpelea
bfda93d66b Merged in alinjerpelea/nuttx (pull request #915)
arch: arm: cxd56xx: I2C, SPISD, Charger and Gauge

* arch: arm: cxd56xx: add I2C character driver

    for testing purposes, we use the CXD56_I2C_DRIVER to register the
    /dev/i2c[] character devices.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: use I2C character driver

    We should use the CXD56_I2C_DRIVER to register the /dev/i2c[]
    character devices.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add battery gauge driver

    add battery gauge driver for cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add charger driver

    add charger driver for cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch:arm: cxd56xx: add SPI SDCard configuration

    Add SPI SDCARD functionality configuration

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable gauge driver

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable charger driver

    enable charger driver on spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-25 12:06:47 +00:00
Alin Jerpelea
c62d90fdb7 Merged in alinjerpelea/nuttx (pull request #914)
configs: spresense: add I2CTOOL support and extend GPIO for future use

* arch: arm: cxd56xx: add delay support

    add delay support for cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: register I2C busses

    for development is usefull to register I2C busses when the I2CTOOL
    is built

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs:spresense: enable GPIO interface

    enable GPIO interface on spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-24 13:39:46 +00:00
Alin Jerpelea
2a32f36540 Merged in alinjerpelea/nuttx (pull request #909)
arch: arm: cxd56xx: SCU, ADC, I2C

* nuttx: configs: spresense: LEDS: fix warnings

    In the initial code several errors were missed because I pushed
    the dirty code.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add Sensor Control Unit (SCU)

    Add Sensor Control Unit (SCU) on cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add I2C support

    add I2C support on cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add ADC interface support

    Add ADC interface support on cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: Use DMAC for reading sensing data

    Use DMAC for reading sensing data from SCU on cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: code style sanitization

    NuttX does not use Deoxygen for documentation and no file should contain Doxygen tags or Doxygen style comments.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable I2CDEV

    add enable I2CDEV for spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: add notification LEDs

    Add usefull diagnostic LEDs on the speresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-18 12:46:43 +00:00
Alin Jerpelea
f50080b251 Merged in alinjerpelea/nuttx (pull request #907)
arch: arm: cxd56xx: add UID support

* arch: arm: cxd56xx: add UID support

    Add support to be able to read the HW UID

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable USERLEDS

    add USERLED for spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-17 22:02:19 +00:00
Alin Jerpelea
92892a8dd7 Merged in alinjerpelea/nuttx (pull request #902)
arch: arm: cxd56xx: PM and PWM

* configs: spresense: add SPI configuration

    add SPI configuration for spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add support for PWM

    add support for PWM for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable PWM support

    enable PWM support on spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add Power Management PROCFS support

    the powermanager procfs support will export
    /proc/pm:
     clock
     power

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable powermanager procfs support

    The powermanager procfs is disabled by default and need to be enabled
    by the CONFIG_CXD56_PM_PROCFS option

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add timer driver

    Add timer driver for cxd56xx.

    NOTE
    The timer allows a divider of 1, 16 and 256 options

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add Watch Dog Timer

    Add Watch Dog Timer on cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable timer

    the platform support has been added and now we can use the timers
    on spresense board.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable WatchDog timer

    The platform support has been added and now we can use the WatchDog
    Timer on spresense board.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-14 18:40:06 +00:00
Alin Jerpelea
a5418405d7 Merged in alinjerpelea/nuttx (pull request #897)
configs: spresense: enable SPI Flash

* arch: arm: cxd56xx: organize menu items

    Group all CXD56xx Options in one menu

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add Storage Options menu

    Add Storage Options menu and Peripheral Support comment

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add SPI Flash support

    add SPI Flash support for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable SPI Flash

    Enable SPI Flash on spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-13 15:04:33 +00:00
Alin Jerpelea
e69471ba2f Merged in alinjerpelea/nuttx (pull request #896)
arch: arm: cxd56xx: add SPI, DMA and RTC

* arch: arm: cxd56xx: add SPI support

    Add SPI support for cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: Add DMA support

    Add DMA support for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add RTC functionality

    Add the RTC functionality for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add RTC_DRIVER

    Add RTC_DRIVER to cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* configs: spresense: enable rtc functionality

    Enable RTC functionality on spresense board

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-13 11:12:40 +00:00
Alin Jerpelea
32f89d63f7 Merged in alinjerpelea/nuttx (pull request #890)
Add syscontrol for cxd56xx

* arch: arm: cxd56xx: add sysctl

    Add the syscontrol implementation for cxd56xx.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: timer updates

    Add the function to change the clock speed.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: cxd56_uart updates

    Add pinctrl and clock ctrl functionality.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add conditional for SDHCI

    The cxd56_sdhci should be built only if CONFIG_CXD56_SDIO is selected

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-11 11:19:31 +00:00
Alin Jerpelea
6498ec8d02 Merged in alinjerpelea/nuttx (pull request #888)
arch: arm: cxd56xx: add Power Management support

* arch: arm: cxd56xx: add Power Management support

    Add power management on the cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add Far API

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-10 23:35:15 +00:00
Alin Jerpelea
215a146f2e Merged in alinjerpelea/nuttx (pull request #884)
arch: arm: cxd56xx: add support for USB and SDIO

* arch: arm: cxd56xx: add support for USB connectivity

    Add basic support for USB connectivity

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add SDHCI support

    We add SDHCI driver for the cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-05 14:05:56 +00:00
Alin Jerpelea
eeedce32c4 Merged in alinjerpelea/nuttx (pull request #881)
updates for arch: arm: cxd56xx:

* arch: arm: cxd56xx: add pinconfig

    Add the HW pin configuration for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add GPIO support

    Add GPIO support for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add support for GPIO interrupts

    add support for GPIO interrupts

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add clock support

    Add clock support for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add PMIC support

    Add support for PMIC (Power management integrated circuit)
    for cxd56xx chip

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add FIFO CPU schedulier

    add a simple FIFO schedulier that minimizes overhead

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* arch: arm: cxd56xx: add ICC support

    add Inter Core Communication for cxd56xx

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-06-05 11:29:51 +00:00
Gregory Nutt
abf6965c24 Squashed commit of the following:
libs/:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    syscall/:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    wireless/:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    Documentation/:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    include/:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    drivers/:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    sched/:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    configs:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    arch/xtensa:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    arch/z80:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    arch/x86:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    arch/renesas and arch/risc-v:  Remove references to CONFIG_DISABLE_SIGNALS.  Signals can no longer be disabled.
    arch/or1k:  Remove all references to CONFIG_DISABLE_SIGNALS.  Signals are always enabled.
    arch/misoc:  Remove all references to CONFIG_DISABLE_SIGNALS.  Signals are always enabled.
    arch/mips:  Remove all references to CONFIG_DISABLE_SIGNALS.  Signals are always enabled.
    arch/avr:  Remove all references to CONFIG_DISABLE_SIGNALS.  Signals are always enabled.
    arch/arm:  Remove all references to CONFIG_DISABLE_SIGNALS.  Signals are always enabled.
2019-04-29 14:52:05 -06:00
Nobuto Kobayashi
eba004d498 arch/arm/src/cxd56xx and arch/arm/include/cxd56xx: Add initial CXD56xx chip sources. 2019-04-22 07:51:22 -06:00