This PR adds the drivers for Allwinner A64 PIO (Programmable I/O) and PinePhone LEDs (Red / Green / Blue).
The PIO Driver is based on the NuttX PIO Driver for Allwinner A10: [`arch/arm/src/a1x/a1x_pio.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_pio.c)
- `arch/arm64/src/a64/Make.defs`: Add PIO Driver to Makefile
- `boards/Kconfig`: Add `ARCH_HAVE_LEDS` to PinePhone
- `boards/arm64/a64/pinephone/src/pinephone.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_boardinit.c`: Start Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Start User LEDs
- `boards/arm64/a64/pinephone/src/Makefile`: Add LED Driver to Makefile
- `boards/arm64/a64/pinephone/configs/nsh/defconfig`: Add `CONFIG_USERLED` to `nsh` config
- `arch/arm64/src/a64/a64_pio.c`, `a64_pio.h`: Allwinner A64 PIO Driver
- `arch/arm64/src/a64/hardware/a64_memorymap.h`: PIO Memory Map
- `arch/arm64/src/a64/hardware/a64_pio.h`: PIO Definitions
- `boards/arm64/a64/pinephone/include/board.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_autoleds.c`: Driver for Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_userleds.c`: Driver for User LEDs
- `introduction/supported_platforms.rst`: Add Allwinner A64 as Supported Platform
- `platforms/arm/a64/boards/pinephone/index.rst`: Add PIO and LEDs to PinePhone
It takes about 10 cycles to obtain the task list according to the task
status. In most cases, we know the task status, so we can directly
add the task from the specified task list to reduce time consuming.
It takes about 10 cycles to obtain the task list according to the task
status. In most cases, we know the task status, so we can directly
delete the task from the specified task list to reduce time consuming.
Config option IMXRT_ADCx_ETC can now be used to select an external HW
trigger to be used instead of continous trigger. Continous trigger is
used if IMXRT_ADCx_ETC = -1 (default option). Otherwise the source signal
is routed through XBAR and used as a trigger.
Hardware triggering is currently limited to maximum of 8 channels.
HW trigger is automatically disabled if there are more than 8 channels.
The external triggering was tested with PWM signal as a source.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
documentation: Fixed typos in ESP32 Secure Boot section
documentation/esp32: Improved note about the MCUboot port
documentation/esp32: Improved instructions in Secure Boot section
documentation/esp32: Fix information in Secure Boot section
documentation/esp32: Added info in Secure Boot section
documentation/esp32: Fix Secure Boot Instructions
This commit allows the PWM modules to be synchronized by an external
signal (other PWM module for example). The sync source can be selected
from configuration.
PWM module can also now generate a trigger when its timer reaches the duty
cycle. This trigger is used for the synchronization of other modules. It
can also be used for triggering ADC for example in the future.
Thanks to Rastislav Pavlanin and Jan Spurek from NXP support for
suggestion which helped to solve the inter-module PWM synchronization
task.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
* boards/arm/tiva/tm4c129e-launchpad: New subdirectory providing
board support for the Texas Instruments TM4C Crypto Connected
LaunchPad, or more correctly the EK-TM4C129EXL.
* Documentation/introduction/detailed_support.rst,
Documentation/introduction/supported_platforms.rst,
boards/README.txt: Document the additional board support.
* boards/Kconfig:
(ARCH_BOARD_TM4C129E_LAUNCHPAD): New config.
(ARCH_BOARD): Add tm4c129e-launchpad.
(Board-Specific Options): Source the board-specific Kconfig
boards/arm/tiva/tm4c129e-launchpad/Kconfig when selected.
since it is impossible to track producer and consumer
correctly if TCP/IP stack pass IOB directly to netdev
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
In order to better test the lcdddev driver and framebuffer, newer
board configs (for the TTGO T-Display and for the simulator) were
added.
Adjusted references of the sim:lvgl_(fb/lcd) config.
This patch adds corrected implementation of FLASH memory to be used
with progmem driver for use with mtd filesystems like nxffs or smartfs.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
This patch adds to the nucleo-wl55jc previously implemented EXTI support.
Button support with nuttx's button driver is added.
I've written small example to show how to use GPIO EXTI. B3 button can be
used (selectable via Kconfig) to toggle Red LED.
I've added new defconfig for demo purposes. I've included there config
and enabled example programs that are meant to demonstrate functions of
the board and does not really have a place in real world project. Like
Red LED can be toggled with B3 button, or LED example that flashes LEDS,
or button example to show which button has been pressed.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- Change (1 << 0) to (1 << BUTTON1_BIT (and similar)
v2 -> v3:
- Fix invalid BUTTON3_BIT value
v3 -> v4:
Suggested by: Petro Karashchenko
- Change 0/1 to false/true
This patch implements working support for EXTI GPIO.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- change (1 << n) to (1 << (n)) in macro definition
- change 1 << X to (1 << X) in code
- fix alignment
v2 -> v3:
Suggested by: Petro Karashchenko
- I was supposed to change (1 << pin) to 1 << pin, not the other way around:)
