As coproc_save/restore only used in context_restore/save.
Use macro instead of function.
Some register use optimize.
Unify with arm/riscv.
Signed-off-by: zhuyanlin <zhuyanlin1@xiaomi.com>
Targets build during the kernel phase did not have their dependencies
specified and thus they were not rebuilt after their dependencies have
changed, for example by changing options in menuconfig.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
The current SAMv7 PWM driver assumes that all PWM channels should
work in sync mode, but that is a partial case of a generic PWM
driver operation.
Start SAMv7 PWM channels in async mode. The sync mode should be
implemeted either using ioctl command or via a separate Kconfig
option.
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- I noticed that rv-virt:knsh64 crashes when it executes the init.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with rv-virt:knsh64
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
1. Add vbat mode for chip internal voltage sample;
2. Add adc channel config;
3. Using DFIFO2 to get the sample value, follow telink sdk.
4. Add calibration function and config;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
When allocation failed, it isn't too uncommon for the caller
to fall back to other allocation method.
(eg. esp32 textheap code tries iram heap when an allocation from rtc heap
failed.)
DEBUGASSERT(false) is too much in that case.
This commit removes the DEBUGASSERT, and also makes the heap dump
a separate option.
The FPU register saving upon vfork entry was missing.
Also added macro that tells the actual size of an FPU reg, instead
of just having a coefficient for qfpu/no-qfpu.
pthread_condclockwait() can not distinguish between interrupt and timeout,
which cause these API not follow POSIX:
pthread_rwlock_timedrdlock()
pthread_rwlock_timedwrlock()
pthread_condtimedwait()
POSIX:
Upon return from the signal handler the thread resumes waiting for
the condition variable as if it wasnot interrupted
These functions shall not return an error code of [EINTR].
Replacing nxsem_wait() with nxsem_clockwait_uninterruptible() can solve it.
Signed-off-by: jihandong <jihandong@xiaomi.com>
- Remove most of the ifeq-conditions and replace them with variables.
- Move the -I flag for 3rd party headers to opensbi/Make.defs
This clean-up / generalization makes it much simpler to add a new SBI
implementation, without the need to add a bunch of ifeq / elif conditions
to the makefile.
