lc823450 dvfs auto
* arch/arm/src/lc823450: Fix up_enable_irq() timing for I2S.
In previous commit, I2S IRQ might be sometimes assigned to CPU1
when CONFIG_SMP=y. This change fixes this issue.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Refactor timer driver.
Introduce lc823450_timer.h and move lc823450_timerisr.c to
lc823450_timer.c Add MTM timer APIs for DVFS. Introduce
up_rtc_gettime() for CONFIG_RTC_HIRES.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Introduce idle time calculation in DVFS
Also, DVFS autonomous mode based on CPU idle time is supported.
NOTE: voltage control is still disabled.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/lc823450-xgevk: Update defconfigs
Enable RTC_HIRES instead of RTC_DATETIME (audio/rndis)
Disable TCP_WRITE_BUFFERS and change SCHED_LPWORKPRIORITY (rndis)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/lc823450-xgevk: Update README.txt
Update SMP and DVFS related part
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Author: Juha Niskanen <juha.niskanen@haltian.com>
Date: Mon Feb 19 15:03:17 2018 -0600
drivers/mtd: mtd_config.c: Add still more error handling (to detect bad underlying flash implementations)
drivers/mtd: mtd_config.c: Remove MTD_ERASE that was erasing data block instead of erase block. This is a partial revert of 4f18b4. Reported-by: Pascal Speck <iktek01@yahoo.com>
arch/arm/src/stm32l4: stm32l4_flash: change flash programming to use page buffer for unaligned writes.
is not done or done after PLL configuration, the STM32 fail to continue boot
operation if the frequency if greater than 24MHz. This common t add this operation according to the board variable STM32_SYSCLK_FREQUENCY. Tested on stm32f334-disco board.
Fix signal handing for smp
* sched/signal: Remove SMP related logic in sig_dispatch.c
This change prevents from a deadlock in up_schedulesigaction.c
where inter-CPU signal handling is actually implemented.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/armv7-m: Fix signal handling for SMP
In previous implementation, signal handling for SMP was incorrect.
Thus, for example, if an inter-CPU signal happened an incorret tcb
was signaled and caused ASSERT().
This change fixes the issues and works for both inter-CPU signal
handling and signal handling on the same CPU.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
SAMDL DMA fixes and experimental SPI support
* SAMDL: Fix DMA controller support
* SAMDL: Added experimental DMA support to SPI driver. spi_exchange() uses a pair of DMA channels for TX and RX
Approved-by: Gregory Nutt <gnutt@nuttx.org>
disable LPC17 FDR when not used (second fix)
if a boot loader sets the fractional divider (FDR) the baud rate in
nuttx will be wrong (multiplied by this fraction).
This also has to be added to lpc17_lowputc.c
Unfortunately the constant used for shifting the bits was wrong in the header file, so it took some time to realize this...
Approved-by: Gregory Nutt <gnutt@nuttx.org>
disable LPC17 FDR when not used
* disable LPC17 FDR when not used
if a boot loader set the fractional divider (FDR) the baud rate in
nuttx will be wrong (multiplied by this fraction).
So if it is not used, it should be disabled.
LPC176x docs say:
"
DIVADDVAL Baud-rate generation pre-scaler divisor value.
If this field is 0, fractional baud-rate generator will
not impact the UARTn baudrate.
MULVAL Baud-rate pre-scaler multiplier value.
This field must be greater or equal 1 for UARTn to operate properly,
regardless of whether the fractional baud-rate generator is used or not.
"
So DIVADDVAL is set to 0 and MULVAL is set to 1.
* symbols found and added
Approved-by: Gregory Nutt <gnutt@nuttx.org>
binfmt/, configs/, grahics/, libc/, mm/, net/, sched/: OS references to the errno variable should always use the set_errno(), get_errno() macros
arch/arm/src/stm32 and stm32f7: Architecture-specific code is not permitted to modify the errno variable. drivers/ and libc/: OS references to the errno variable should always use the set_errno(), get_errno() macros
sched/sched: Correct some build issues introduced by last set of changes.
sched/sched: Add new internal OS function nxsched_setaffinity() that is identical to sched_isetaffinity() except that it does not modify the errno value. All usage of sched_setaffinity() within the OS is replaced with nxsched_setaffinity().
sched/sched: Internal functions sched_reprioritize() and sched_setpriority() no longer movidify the errno value. Also renamed to nxsched_reprioritize() and sched_setpriority().
sched/sched: Add new internal OS function nxsched_getscheduler() that is identical to sched_getscheduler() except that it does not modify the errno value. All usage of sched_getscheduler() within the OS is replaced with nxsched_getscheduler().
sched/sched: Add new internal OS function nxsched_setparam() that is identical to sched_setparam() except that it does not modify the errno value. All usage of sched_setparam() within the OS is replaced with nxsched_setparam().
sched/sched: Add new internal OS function nxsched_getparam() that is identical to sched_getparam() except that it does not modify the errno value (actually, the previous value erroneously neglected to set the errno value to begin with, but this fixes both issues). All usage of sched_getparam() within the OS is replaced with nxsched_getparam().
