Summary:
- During repeating ostest with sabre-6quad:smp (QEMU),
I noticed that pthread_rwlock_test sometimes stops
- Finally, I found that nxtask_exit() released a critical
section too early before context switching which resulted in
selecting inappropriate TCB
- This commit fixes this issue by moving nxsched_resume_scheduler()
from nxtask_exit() to up_exit() and also removing
spin_setbit() and spin_clrbit() from nxtask_exit()
because the caller holds a critical section
- To be consistent with non-SMP cases, the above changes
were done for all CPU architectures
Impact:
- This commit affects all CPU architectures regardless of SMP
Testing:
- Tested with ostest with the following configs
- sabre-6quad:smp (QEMU, dev board), sabre-6quad:nsh (QEMU)
- spresense:wifi_smp
- sim:smp, sim:ostest
- maix-bit:smp (QEMU)
- esp32-devkitc:smp (QEMU)
- lc823450-xgevk:rndis
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
1.Reduce the default size of task_group_s(~512B each task)
2.Scale better between simple and complex application
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ia872137504fddcf64d89c48d6f0593d76d582710
There was broken logic around serial initialization function
prototype. Pointers were also being cast directly to uint32
without first being cast to uintptr.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
since exit will be only callable from userspace and change
the 1st argument from "const uint8_t *" to "const char *"
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I86487d57210ab63109148232da71dbc4d60a563b
utilize the call inside nxtask_exit instead, also move
nxsched_suspend_scheduler to nxtask_exit for symmetry
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I219fc15faf0026e452b0db3906aa40b40ac677f3
And remove syslog_init_e because all initialization is later now and we don't
distinguish the initialition phase anymore after ramlog don't need special
initialize.
Because we can get the same function by CONSOLE_SYSLOG/syslog_console_init.
BTW, it isn't a good choice to use g_ramlogfops as /dev/console since nsh
will read back what it send out which will surprise most people.
it doesn't make sense that iob initialization is in up_initialize
but other memory components initialization is called in nx_start
Change-Id: Id43aeaa995f340c5943f59a0067a483ff3ac34a2
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Call xxx_timer_initialize from clock subsystem to make timer ready for use as soon as possiblei and revert the workaround:
commit 0863e771a9
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Apr 26 07:24:57 2019 -0600
Revert "sched/clock/clock_initialize.c: clock_inittime() needs to be done with CONFIG_SCHED_TICKLESS and clock_initialize should skip clock_inittime() for external RTC case since the RTC isn't ready yet."
This reverts commit 2bc709d4b9.
Commit 2bc709d4b9 was intended to handle the case where up_timer_gettime may not start from zero case. However, this change has the side-effect of breaking every implementation of tickless mode: After this change the tickless timer structures are used before they are initialized in clock_inittime(). Initialization happens later when up_initialize is called() when arm_timer_initialize().
Since the tickless mode timer is very special, one solution might be to
1. Rename xxx_timer_initialize to up_timer_initialize
2 Move up_timer_initialize to include/nuttx/arch.h
3. Call it from clock subsystem instead up_initialize
Basically, this change make timer initialization almost same as rtc initialization(up_rtc_initialize).
For now, however, we just need to revert the change.
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Squashed commit of the following:
configs/: The few configurations that formerly set CONFIG_NFILE_DESCRIPTORS=0 should not default, rather they should set the number of descriptors to 3.
fs/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
tools/: Tools updates for changes to usage of CONFIG_NFILE_DESCRIPTORS.
syscall/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
libs/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
include/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
drivers/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
Documentation/: Remove all references to CONFIG_NFILE_DESCRIPTORS == 0
binfmt/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
arch/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
net/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
sched/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
sched/Kconfig: CONFIG_NFILE_DESCRIPTORS may no longer to set to a value less than 3
configs/: Remove all settings for CONFIG_NFILE_DESCRIPTORS < 3
sched/init/nx_bringup.c: Fix a naming collision.
sched/init: Rename os_start() to nx_start()
sched/init: Rename os_smp* to nx_smp*
sched/init: Rename os_bringup to nx_bringup
sched/init: rename all internal static functions to begin with nx_ vs os_
Squashed commit of the following:
Trivial, cosmetic
sched/, arch/, and include: Rename task_vforkstart() as nxtask_vforkstart()
sched/, arch/, and include: Rename task_vforkabort() as nxtask_vforkabort()
sched/, arch/, and include: Rename task_vforksetup() as nxtask_vfork_setup()
sched/: Rename notify_cancellation() as nxnotify_cancellation()
sched/: Rename task_recover() to nxtask_recover()
sched/task, sched/pthread/, Documentation/: Rename task_argsetup() and task_terminate() to nxtask_argsetup() and nxtask_terminate(), respectively.
sched/task: Rename task_schedsetup() to nxtask_schedsetup()
sched/ (plus some binfmt/, include/, and arch/): Rename task_start() and task_starthook() to nxtask_start() and nxtask_starthook().
arch/ and sched/: Rename task_exit() and task_exithook() to nxtask_exit() and nxtask_exithook(), respectively.
sched/task: Rename all internal, static, functions to begin with the nx prefix.
