Here is the email loop talk about why it is better to remove the option:
https://groups.google.com/forum/#!topic/nuttx/AaNkS7oU6R0
Change-Id: Ib66c037752149ad4b2787ef447f966c77aa12aad
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on .c files and fix the issues
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
arch/stm32 ensure all spi dma handler check the result
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on .c and .h files and fix it
Author: Alin Jerpelea <alin.jerpelea@sony.com>
drivers: usbdev: minor fix
drivers: usbdev: usbmsc full speed not available
Change transfer size to be based on maxpacket size.
drivers: usbdev: Fix string ID calculation
For *_STRBASE defines, it already unnecessary because composite device setup
has been changed, it would be calculated by *_composite.c in board sources.
drivers: usbdev: Fix invalid/unsupported command processing
Mass Storage Class shall stall when invalid or unsupported commands
has been recieved.
drivers: usbdev: Remove unnecessary reset logic
drivers: usbdev: Flags comparison fix
drivers: usbdev: Descriptor type mismatch fix when dual speed is enabled
* arch: risc-v: Remove unused typedef for irqstate_t
NOTE: irqstate_t is defined in arch/risc-v/include/types.h
* arch: risc-v: Add typedef irqstate_t for __LP64__
* arch: risc-v: Add SMP support to K210 (RV64GC) processor
* boards: maxi-bit: Update READMEs and add smp/defconfig
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle against .c .h files and fix it
Author: Adam Feuer <adam@starcat.io>
Summary
Adds CDC ECM Ethernet over USB High Speed for SAMA5D36-Xplained
(and maybe other boards) (most of the code was there already,
but didn't work out of the box for the SAMA5D36-Xplained)
Only SAMA5D36-Xplained has been tested so far
Impact
None if you don't use the CDC ECM Ethernet driver
On SAMA5D36-Xplained, this adds high-speed Internet connectivity
over USB 2.0 High Speed. via the USB CDC ECM Gadget driver.
It may work on other boards too.
This also fixed full-speed (low-speed) mode for the board too.
Limitations
Hasn't been tested on anything other than SAMA5D36-Xplained board.
TODO
Ideally this would include a composite RNDIS device so it would
also work seamlessly on Windows. That is for a future PR
Ideally this would include software to help configuration via
mDNS/DNS-SD for plug and play compatibility with Linux and macOS.
That is for a future PR.
Detail
Only a few lines of C driver code needed to be changed, since the
capability was there already. The rest is config and documentation.
Changes the SAMA5D3-Xplained board bringup to match the SAMA5D3-EK
board bringup
A helper script to configure Linux routing and iptables NAT is also
provided, along with documentation on how to use it.
Testing
Manual, on a Ubuntu Linux 19.10 system and MacOS 10.14.6 Mojave
MacBook Pro.
How To Verify
Follow the new CDC ECM Ethernet over USB instructions in the board
README.txt file
Commits:
remove non-UTF-8 chars in comment and reformat
removed unneeded comment markers
instructions for using the defconfigs
removed EMAC from config
- to prove this example only needs the CDC ECM Ethernet over USB to work
added CDC-ECM Ethernet over USB info to README
added U-Boot image
added netusb helper script
- this can configure the Linux network interface and routes
so you can ping or access the NuttX system via TCP/IP.
renamed defconfig dirs to be ethernet-over-usb
- was usb-over-ethernet which is not right
added USB DMA to defconfigs
updated readme with autoboot and debugging info
bringing ethernet-over-usb examples into parity
added cdc ecm ethernet over usb with telnetd config
added defconfig
only use phy interrupt if netdevices is ethernet
- because now netdevice could be CDC ECM ethernet over usb
which has no PHY interrupt
add bringup to Makefile
add bringup
app init cleanup
init cdc ecm driver and rndis driver; some cleanup
fixed some typos and odd characters
usb over ethernet working over usb 2.0 hs
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on all .c and .h and fix all issues
Author: Alin Jerpelea <alin.jerpelea@sony.com>
drivers: mtd: smart: Add smartfs fsck feature
Support fsck to check and repair the smartfs file system. If the power
loss occurs during writing into the flash, the dead space are created
in flash after the next power cycle. To avoid this problem, introduce
fsck and keep the consistency of file system in initializing smartfs.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
commit 60927c5fb6a353994341601f55071c618e97682b
Author: Alin Jerpelea <alin.jerpelea@sony.com>
Date: Thu Dec 28 18:27:21 2017 +0900
drivers: mtd: smart: Fix duplicate sector selection in SmartFS
Add care for 16-bit sequence without CRC.
drivers: mtd: smart: Check CRC of duplicate sectors
In the illegal case by power-loss, when the multiple logical sectors are
duplicated, we compare the sequence number of each sector and select the newer
sector. Just in case, add CRC check for the newer sector. If the newer sector
has CRC error, then we use the older sector.
drivers: mtd: smart: SPI-Flash recovery from the initial error state
The FLASH may be not erased in the initial delivery state.
Just in case for the recovery of this fatal situation,
after once erasing the sector, return the sector as a free sector.
drivers: mtd: smart: Fix error handling in smartfs mtd driver
Add error handling in relocate sector.
drivers: mtd: smart: Fix initialize sector sequence value in smartfs
Fix initialization of sequence value into sector header and also avoid
unaligned memory access when CONFIG_MTD_SMART_ENABLE_CRC=n.
drivers: mtd: smart: Fix handling of duplicate sector in smartfs
In smartfs scan, if duplicate logical sector is found on the device,
then smartfs selects the winner sector by comparing sequence number,
and the loser sector is soon released. Fix a bug this loser sector
is registered into logical-to-physical sector mapping table.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle to check .c and .h files and fix reported issues
Author: liuzhao <happypapa@yeah.net>
Add Quectel EC20 4G LTE Module USB CDC/ACM support
This function fails to compile due to numerous undeclared register definitions used in cxd56_audio_bca_reg.c. This commit replaces the undefined definitions with very similar definitions recommended by GCC (differing only in some spelling).
However, I cannot be certain that this is correct. This must be reviewed, corrected, and verified by Alin Jerpelea. Please do not merge until Alin approves.
The configuration that demonstrates the failure is spresense:audio.
nrf52: add support for GPIO interrupts
nrf52: add macros to decode GPIO PIN and GPIO PORT
nrf52: various cosmetic changes
nrf52: fix GPIO P1 memory address
boards/nrf52840-dk: add support for SPI
boards/nrf52840-dk: add support for LSM6DSL sensor
boards/nrf52840-dk: add support for SX127X radio
In previous commit, mstatus.mie was set when creating a new task
but this change was incorrect and had a side effect such that
a machine interrupt would be enabled just before returning from
interrupt handling routine to switch context.
Also, mstatus.mpp is set to machine mode in up_get_newintctx()
instead of fe310_dispatch_irq().
Author: Alan Carvalho de Assis <acassis@gmail.com>
Check all .c and .h against nxstyle and fix it.
Author: Alin Jerpelea <alin.jerpelea@sony.com>
fs: smartfs: Fix over capacity write
When the remaining capacity of flash is one sector, if a new root
directory is created by file open, then the root directory's chain is
broken and it causes to SmartFS filesystem crash. Once this fatal
problem occurs, it's impossible to recover even if the system reboot.
Fix it by finally update link of root directory.
fs: smartfs: Fix buffer overrun
fs: smartfs: Fix uninitialized variable warnings
fs: smartfs: Memory leak fix
boards: cxd56xx: Update spresense board.h
- Fix PMIC assignment
- Add specific pin configurations for spresense
- Remove unnecessary definitions
arch: cxd56xx: Add ITM syslog init at startup
arch: cxd56xx: Enable DMA settings dynamically
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix small typos and check against nxstyle
Author: Gregory Nutt <gnutt@nuttx.org>
boards/arm/lpc43xx/bambino-200e/src/lpc43_appinit.c: Eliminate a warning found in build testing.
The removal of (void) from all functions whose return value has been ignored has introduced several new warnings into the build test output. For example in lpc3_appinit(), I now see this:
# define nsh_spifi_initialize() (OK)
and
nsh_spifi_initialize();
which generaterd a new warning: "warning: statement with no effect [-Wunused-value]". This commit fixes that warning.
Description:
Fix two warnings found in build testing: (1) Need to include nuttx/semaphore.h
from prototype of nxsem_post() and (2) need to initialize return value of function.
Uninittialized garbage was being returned on success.Fix two warnings found in
build testing: (1) Need to include nuttx/semaphore.h from prototype of
nxsem_post() and (2) need to initialize return value of function.
Uninittialized garbage was being returned on success.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Verify all .c and .h against nxstyle, fixed the Mixed cases
Author: Alin Jerpelea <alin.jerpelea@sony.com>
cxd56xx improvements (#48)
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* tools/nxstyle.c: Donot check unknown file extension files
nxstyle only support c soure file and header file check, donot check
other unknown file extension files.
* tools/checkpatch.sh: Add checkpatch.sh script based on nxstyle tool
Usage:
checkpatch.sh patch-list // default as patch list
checkpatch.sh -p patch-list
checkpatch.sh -c commit-list
checkpatch.sh -f file-list
checkpatch.sh - // read from stdin, which used by git pre-commit hook
And git pre-commit hook could use checkpatch.sh as below:
git diff --cached | ./tools/checkpatch.sh -
Run all .c and .h files in last PR through nxstyle.
Author: 脚蹬破拖鞋 <happypapa@yeah.net>
Add Imxrt usdhc insert or remove detection (#43)
* Add usdhc card insertion and removal detection using interrupt for imxrt.
* Add interrupt handle when usdhc insert or remove.
This commit fixes a compilation error that occurs when enabling the
following configuration items for stm32f7 and stm32h7 architectures:
CONFIG_DEBUG_FEATURES=y
CONFIG_DEBUG_ERROR=y
CONFIG_DEBUG_WARN=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_IRQ=y
CONFIG_DEBUG_IRQ_ERROR=y
CONFIG_DEBUG_IRQ_WARN=y
CONFIG_DEBUG_IRQ_INFO=y
The compiler error for stm32f7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:497:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_FIRST'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_FIRST
chip/stm32_irq.c:497:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
And the compiler error for stm32h7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'stm32_dumpnvic':
chip/stm32_irq.c:164:4: warning: #warning Missing logic [-Wcpp]
# warning Missing logic
^~~~~~~
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:522:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_CRS'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_CRS
chip/stm32_irq.c:522:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
This commit replaces all STM32_IRQ_NIRQS defines with the NR_IRQS
define, which seems to be consistent with the rest of the code in
Nuttx.
* Documentation/NuttXCCodingStandard.html: Remove requirement to decorate ignored returned values with (void).
* sched_mergepending.c: Correct some errors in comments.
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
Usage: ./nxstyle -r start,count filename
nxstyle with -r option used to parse the range lines rather than the whole file.
Change-Id: I58ec56511fde14d6ec914400a7849e69960a3711
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
