ESP32 SoC use a static allocated array as idle stack. To fit
the existed idle stack allocation, make idle stack allocated
from ebss for the whole esp32 series.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Although almost all board support allocating idle stack after ebss,
bl602 have a different memory layout for idle stack. To unify them,
make idle stack allocated from ebss for bl602.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
This patch can boot `rv-virt/knsh64` and `rv-virt/knsh32` reported in
issue #12275 with qemu 6.2 target and OpenSBI v1.0 firmware on Ubuntu
22.04 host.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
The qemu-rv use a small init code for M mode in kernel build.
It is hard-coding and is difficult to change. Due to the fact,
introduce a already mature SBI implement (e.g OpenSBI) to
replace existing code is a better choice.
This patch introduce some change for qemu-rv:
1. use SSTC to provide time interrupt in kernel build
2. remove uncessary M mode trap.
For simplicity, this patch does not add support for booting
nuttx for any core, but force boot core to start core 0 and
let core 0 do the initialization.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
It is misleading to allocate stack from static array and heap,
make all stack allocated from heap area.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Extracting global variable information using scripts:
kasan_global.py:
1. Extract the global variable information provided by the -- param asan globals=1 option
2. Generate shadow regions for global variable out of bounds detection
Makefile:
1. Implement multiple links, embed the shadow area into the program, and call it by the Kasan module
Signed-off-by: W-M-R <mike_0528@163.com>
RTC data was not being correctly placed on RTC's memory data due to
linker issues. Also, the image's RTC memory segment was not being
properly parsed by the bootloader.
Currently only FLAT mode development can enjoy cmake build system. This
patch tries to add initial kernel mode support. It can build NuttX kernel
and libproxies.a, the latter will be further checked though.
This can already help to build an AMP remote node image as it can share
userland apps living in the AMP master node.
Major changes:
- in top folder:
- CMakeLists.txt adjust for KERNEL mode, separate from PROTECTED mode.
- in `syscall`:
- CMakeLists.txt add mksyscall target for stubs/proxies generation
- in `syscall/stubs`:
- CMakeLists.txt use dependency to mksyscall
- in `syscall/proxies`:
- CMakeLists.txt use dependency to mksyscall
- in `arch`:
- CMakeLists.txt separate KERNEL from PROTECTED mode.
- in `arch/risc-v/src`:
- CMakeLists.txt separate from PROTECTED mode, add sub folders.
- in `arch/risc-v/common`:
- CMakeLists.txt add sources and sub-folders for KERNEL mode.
- in `arch/risc-v/k230`:
- CMakeLists.txt add sources for KERNEL mode.
- in `boards/risc-v/k230/canmv230/src`:
- CMakeLists.txt adjust k230 specific scripts for kernel mode.
New additions:
- in `arch/risc-v/src/nuttsbi/` add CMakeLists.txt
- in `arch/risc-v/src/common/supervisor/` add CMakeLists.txt
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
When an application is being loaded `up_addrenv_create ` calls
`create_region` to create the address environment. Only the first
entry is mapped when the region is created. Virtual memory that is
not mapped will trigger an exception when accessed. Other memory
pages are allocated and mapped on-demand. This enables setting
larger heap and stack for the process without compromising the
overall system memory.
Previously we need turn off the PMP locks in K230 vendor u-boot to use
NuttX, this complicates the setup process. This patch supports running
NuttX with original vendor u-boot so that to reduce setup complexity.
It also enables empty NSH prompt string in AMP master config as the apps
side support is ready.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This patch update documents to reflect the fact that remote node is kicked
off by master node. It also adds debug dump to aid the MISA reading issue
investigation.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This patch adds inter-processor interrupt support using K230 mailbox
device to improve the RPMsg efficiency. The polling logic has been
dropped.
Major changes:
- in arch/risc-v/include/k230:
- irq.h add IRQ for IPI devices
- in arch/risc-v/src/k230:
- Kconfig add IPI related config, increase polling delay
- Make.defs add k230_ipi.c to CHIP_SRCS
- k230_hart.c fix typo, add notes of zero MISA reading w/ NUTTSBI
- k230_irq.c use K230_PLIC_IRQS as ext IRQ limit to support IPI
- k230_rptun.c use IPI instead of polling
- in boards/risc-v/k230/canmv230/configs
- master enable IPI support
- remote enable IPI, TMPFS, RPMSGFS etc
New additions:
- in arch/risc-v/src/k230:
- k230_ipi.h add K230 IPI related defintions
- k230_ipi.c add K230 IPI driver
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This commit implements the RMT peripheral for all the supported
Espressif's RISC-V devices. It also implements the support for the
WS2812 addressable RGB LED using the RMT peripheral.
This patch revises `k230_hart.[ch]` by:
- revising big core boot/stop control.
- making k230_hart_is_big() available in S-mode.
- adding more comments.
This patch also revises the `ld-kernel.script` so that to match the
latest MMU pgtable design.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
K230 chip has two T-Head C908 RiscV cores, previously we run NuttX
on either little or big cores. This patch runs NuttX on both cores
with OpenAMP support via the RPTUN driver.
New additions:
- in arch/risc-v/src/k230
- k230_rptun.c K230 RPTUN driver
- k230_rptun.h K230 RPTUN driver header file
- in baords/risc-v/k230/canmv230
- configs/master Build config for master node
- configs/remote Build config for remote node
- scripts/ld-rptun.script Build script for RPTUN
Major changes:
- arch/risc-v/Kconfig Select NUTTSBI_LATE_INIT upon NUTTSBI
- in arch/risc-v/include
- k230/irq.h Add UART3 IRQ defs
- in arch/risc-v/src/k230
- Kconfig Add RPTUN related config items
- Make.defs Add k230-rptun.c to sources
- hardware/k230_memorymap.h Add K230 device and CSR defs
- k230_hart.c Add hart ctrl for RPTUN
- k230_hart.h Add hart ctrl for RPTUN
- k230_mm_init.c Add Svpmbt to support RPTUN
- k230_start.c Revised to support RPMsg UART
- in boards/risc-v/k230/canmv230
- scripts/Make.defs Add RPTUN script selection
- src/canmv_init.c Add RPTUN and RPMsg_UART initialization
- in Documentation/platforms/risc-v/k230/boards/canmv230
- index.rst Add AMP usage information.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Summary:
- This commit adds nxrecorder to netnsh/netnsh_smp/netnsh64/
netnsh64_smp defconfigs.
Impact:
- None
Testing:
- Tested with qemu-8.2.0 on Raspi4B with USB Audio
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Weak function sometimes can't have strong implementation linked.
This patch uses NUTTSBI_LATE_INIT config and normal function instead
to avoid those issues.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
