This change adds support for the following features:
1. PWM complementary outputs
2. interface for low-level PWM operations
3. support for all PWM channel modes
4. support for internal PWM channels (TIM1/TIM8)
5. support for PWM channel polarity and IDLE state
6. support for TRGO and BREAK
Kientis:edma Cleanup
Kinetis:EDMA Interrupt on last TCD
Kintis:edma remove dcache operations on passed data
Data can be chained in TCD and both read and write
can be in the chain. So the dmach ttype is not
relevent for all; the TCDs. Therefor we only perform
dcache operations on internal strutures, The caller
must perform dcache operations on their data.
kinetis:EDMA TCD Alignment of 32 Bytes to support Scatter/Gather
Summary:
- I noticed that ps shows incorrect stack usage when running
getprime in the background.
- With CONFIG_ARCH_ADDRENV=y, a user task including pthread
allocates its stack in the user space that needs to be
accessed with a correct address environment.
- This commit fixes this issue.
Impact:
- CONFIG_ARCH_ADDRENV=y only
Testing:
- Tested with sabre-6quad:knsh on qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
RX_FIFO_ADDRs and TX_FIFO_ADDR were misconfigured. These addresses
overlapped causing data corruption during high USB loads. For
example, data corruption was present during the following conditions:
1. Composite USB driver was used (CDC/ACM + Mass storage)
2. /dev/ttyACM0 was accessed instantly from Linux side when
starting up.
3. Training data was sent to /dev/ttyACM0 from NuttX from the
very beginning periodically.
It was observed that while Mass storage was negotiating, sometimes
data sent from NuttX to Linux via CDC/ACM was corrupt, although it
was sent properly on the TX fifo.
Also, don't access TXCSRL_REG_EPN_TX_FIFO_NE_MASK for EP0 as it's
not applicable.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
ld: arch/libarch.a(cxd56_allocateheap.c.obj): in function `up_allocate_heap':
arch/arm/src/cxd56xx/cxd56_allocateheap.c:113: multiple definition of `up_allocate_heap'; arch/libarch.a(arm_allocateheap.c.obj):
arch/arm/src/common/arm_allocateheap.c:110: first defined here
Signed-off-by: chao.an <anchao@xiaomi.com>
arch/arm/src/common/arm_hostfs.c: In function 'host_read':
arch/arm/src/common/arm_hostfs.c:156:24:
warning: passing argument 1 of 'up_invalidate_dcache' makes integer from pointer without a cast [-Wint-conversion]
156 | up_invalidate_dcache(buf, buf + count);
| ^~~
| |
| void *
In file included from arch/arm/src/common/arm_hostfs.c:26:
include/nuttx/cache.h:261:37: note: expected 'uintptr_t' {aka 'unsigned int'} but argument is of type 'void *'
261 | void up_invalidate_dcache(uintptr_t start, uintptr_t end);
| ~~~~~~~~~~^~~~~
Signed-off-by: chao.an <anchao@xiaomi.com>
Initialize .domains_init function entry point in sbi_platform_operations when
CONFIG_OPENSBI_DOMAINS=y. In this case, the board specific code must provide
the "board_domains_init" function.
Signed-off-by: Jouni Ukkonen <jouni.ukkonen@unikie.com>
- Introduce the ESP32_WIFI option to replace the broader
ESP32_WIRELESS option. ESP32_WIRELESS is used by both WIFI and BLE.
- Move common functions from esp32_wifi_adapter to esp32_wireless.
- Change the order of including the external libraries to avoid undefined references.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
This commit adds RX DMA support to serial driver. The DMA is currently
supported only for USART peripherals, not for UART. It uses two circular
buffers which size can be setup by SAMV7_SERIAL_RXDMA_BUFFER option.
The idle bus interrupt is enabled to ensures data are read even if the
buffer is not yet full. The timeout can be setup by
SAMV7_SERIAL_DMA_TIMEOUT option.
This adds support only for RX transfers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds functions sam_dmarxsetup_circular() and
sam_dmarxstart_circular() that create API for operating with two or more
circular buffers. This can be used for DMA operation with serial driver
or ADC where ping pong buffers are required to successfully transfer the
data at high speed.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit enhances SAMV7 serial driver with RS-485 mode available to
USART peripherals. The hardware automatically sets RTS pin high when
data are transfered and low then no transfer occurs. Only USART peripherals
support this mode, UART peripherals do not.
This mode can be enabled by configuration option SAMV7_USARTx_RS485MODE.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Summary:
- Since the stack coloration is done for every 32bits
this function should be done in the same way.
Impact:
- None
Testing:
- Tested with qemu-a53:nsh
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
N/A
Summary:
Arm64 support for NuttX, Features supported:
1. Cortex-a53 single core and SMP support: it's can run into nsh shell at
qemu virt machine.
2. qemu-a53 board configuration support: it's only for evaluate propose
3. FPU support for armv8-a: FPU context switching at NEON/floating-point
TRAP is supported.
4. psci interface, armv8 cache operation(data cache) and smccc support.
5. fix mass code style issue, thank for @xiaoxiang781216, @hartmannathan @pkarashchenko
Please refer to boards/arm64/qemu/qemu-a53/README.txt for detail
Note:
1. GCC MACOS issue
The GCC 11.2 toolchain for MACOS may get crash while compiling
float operation function, the following link describe the issue
and give analyse at the issue:
https://bugs.linaro.org/show_bug.cgi?id=5825
it's seem GCC give a wrong instruction at certain machine which
without architecture features
the new toolchain is not available still, so just disable the MACOS
cibuild check at present
Signed-off-by: qinwei1 <qinwei1@xiaomi.com>
1. Fix error recovery mechanism during transmission error
handling (enable transmission at the end).
2. Fix compilation / operation with CONFIG_SAMV7_EMAC_PREALLOCATE=y
3. Enable fully configured address space for transmission queues
to allow sending packets with length more than 976 bytes. With
partially configured address space the AHB error is generated
during transmission of long packets.
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
With faster data transfer rates, it was seen that the read
requests occasionally were issued while the USB RX operation
was actually in progress. This patch makes sure the system
doesn't accidentally read the RX fifo while it's being filled
up, but rather, checks for the RXCSRL_REG_EPN_RX_PKT_RDY_MASK
flag. This flag indicates the packet is ready to be read.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
cache_dbus_mmu_set and cache_ibus_mmu_set return positive values in case
of errors, so DEBUVERIFY could never detect them since this macro checks
for negative values.
Besides, the successful execution of those functions is mandatory for
the reliable operation under Protected Mode, so the verification is
always performed, even when DEBUG is not enabled.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
forget to update in this patch:
commit b02db04e00
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Date: Sun Jun 5 17:10:19 2022 +0800
arch/assert: Keep the thread dump column order same as ps
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
1.Move __XSTR from include/arch.h to include/irq.h
2.Move FLOAD/FSTORE and REGLOAD/REGSTORE from include/arch.h to src/common/riscv_internal.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
* arch/arm/src/tiva/common/tiva_lowputc.c
(tiva_lowsetup):
For each UART, if Kconfig enables RTS/CTS (e.g.,
CONFIG_UART0_IFLOWCONTROL and/or CONFIG_UART0_OFLOWCONTROL),
configure the corresponding GPIO(s).
* arch/arm/src/tiva/common/tiva_serial.c:
(struct up_dev_s):
If CONFIG_SERIAL_IFLOWCONTROL, add a bool field 'iflow'. If
CONFIG_SERIAL_OFLOWCONTROL, add a bool field 'oflow'. This is
inspired by the implementation for kinetis.
(g_uart0priv, g_uart1priv, g_uart2priv, g_uart3priv, g_uart4priv,
g_uart5priv, g_uart6priv, g_uart7priv):
If Kconfig enables RTS/CTS for a UART (e.g.,
CONFIG_UART0_IFLOWCONTROL thru CONFIG_UART7_OFLOWCONTROL), set
the corresponding iflow and/or oflow flag(s).
(up_setup):
Check the above-mentioned iflow and oflow flags and set or unset
the RTSEN and/or CTSEN bits in the UART's CTL register to enable
the feature.
The "p" format specifier already prepends the pointer address with "0x"
when printing.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Sync driver interfaces, also fixes the handling of special pin value for
esp32s2_gpio_matrix_in and esp32s2_gpio_matrix_out functions
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
