This makes the user interface a little hostile. People thing of an MTU of 1500 bytes, but the corresponding packet is really 1514 bytes (including the 14 byte Ethernet header). A more friendly solution would configure the MTU (as before), but then derive the packet buffer size by adding the MAC header length. Instead, we define the packet buffer size then derive the MTU.
The MTU is not common currency in networking. On the wire, the only real issue is the MSS which is derived from MTU by subtracting the IP header and TCP header sizes (for the case of TCP). Now it is derived for the PKTSIZE by subtracting the IP header, the TCP header, and the MAC header sizes. So we should be all good and without the recurring 14 byte error in MTU's and MSS's.
Squashed commit of the following:
Trivial update to fix some spacing issues.
net/: Rename several macros containing _MTU to _PKTSIZE.
net/: Rename CONFIG_NET_SLIP_MTU to CONFIG_NET_SLIP_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_6LOWPAN_MTU to CONFIG_NET_6LOWPAN_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_ETH_MTU to CONFIG_NET_ETH_PKTSIZE. This is not the MTU which does not include the size of the link layer header. This is the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename the file d_mtu in the network driver structure to d_pktsize. That value saved there is not the MTU. The packetsize is the memory large enough to hold the maximum packet PLUS the size of the link layer header. The MTU does not include the link layer header.
Signal handlers maybe run with interrupts enabled or disabled, depending on how the task the received the signal was blocked. (i.e.: If sem_wait() is called, then we disable interrupts, then block the currently running task). This could be dangerous, because user code would be running with interrupts disabled.
This change forces interrupts to be enabled in up_sigdeliver() before executing the signal handler calling up_irq_enable() explicitly. This is safe because, when we return to normal execution, interrupts will be restored to their previous state when the signal handler returns.
configs/flipnclick-pic32mz: Add an nxlines configuration for use in testing the custom HiletGo Click board.
arch/mips/src/pic32mz: Correct some SPI-related typos. configs/flipnclick-pic32mz: Finishes integration of HiletGo OLED. drivers/lcd: Finish support for HiletGo OLED.
drivers/lcd: Add configuration support for HiletGo OLED. configs/flipnclick-pic32mz: Add board support for HiletGo OLED.
arch/mips/src/pic32mz: Fix some typos in debug instrumentation in pic32mz-gpio.c; fix some types releated to UART5 configuration in pic32mz-serial.c.
configs/flipnclick-pic32mz/nsh: Switch serial console to UART3. There is some problem with the UART4 RX pin documentation or configuration.
configs/flipnclick-pic32mz: Switch the serial console to UART4. Clean up some minor issues the LED options.
configs/flipnclick-pic32mz: Add support for two on-board buttons: T1 and T2.
configs/flipnclick-pic32mz: Adds basic board support for the Mikroe Flip&Click PIC32MZ board. Initial commit is just the configs/pic32mz-starterkit with some name chanages.
arch/mips/src/pic32mz: Commits the basic architecture port for the PIC32MZEF.
arch/mips/src/pic32mz: Begin adding PIC32MZEF files. Initial commit are simply PIC32MZEC files with name changes.
arch/mips/include/pic32mz: Add support for the PIC32MZEF family.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
Provide a user defined callback context for irq's, such that when
registering a callback users can provide a pointer that will get
passed back when the isr is called.
