Add basic functions for NAT (NAPT), remaining some logic unimplemented (UDP, ICMP, port assignment, etc). NAT for TCP can work now (unless port conflicts).
Outbound: LAN -> Forward -> NAT(only if targeting at WAN) -> WAN
Inbound: WAN -> NAT(only from WAN, change dest) -> Forward -> LAN
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
1.Add cellular link layer enum definition and register flow
2.Add ioctl flow to set cellular NICs parameters
Signed-off-by: luojun1 <luojun1@xiaomi.com>
Signed-off-by: chao an <anchao@xiaomi.com>
add config CONFIG_NET_ALLOC_CONNS to support allocate connect.
Use this feature if the number of connections can not be determined at
compile time. When enabled the stack will be compiled without the static
pre-allocate connection list and all connection instances will be dynamically
allocated from heap at run time.
Signed-off-by: chao.an <anchao@xiaomi.com>
so netdb could reuse these global variable directly
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Iaa26ddbdaf416f64d43c6e8888a14bbe0c3405eb
* The appropriate size of stack varies among archs.
E.g. for 64-bit sim, 2048 is way too small, especially when the task
happens to use host OS functionalities.
I plan to allow an arch provide its own default.
* I plan to use this to replace hardcoded "STACKSIZE = 2048" in APPDIR.
Historically, the loopback driver used the largest packet size of all enabled link layer protocols. This permitted packets to be forward via the loopbak device with no major loss of performance. However, in experimenting with configurations where no other link layer protocols were enabled, this means the loopback packet size was set to the smallest possible size, to the SLIP minimum of 296 bytes. This resulted in terrible loopback performance.
This commit adds an option to increase the loopback packet size with the option CONFIG_NET_LOOPBACK_PACKETSIZE.
The loopback driver packet buffer should be quite large. The larger the loopback packet buffer, the better will be TCP performance of the loopback transfers. The Linux loopback device historically used packet buffers of size 16Kb, but that was increased in recent Linux versions to 64Kb. Those sizes may be excessive for resource constrained MCUs, however.
The network still enforces the lower limit that is the maximum packet size of all enabled link layer protocols. But this new option permits the loopback packet size to be increased from that.
* net/Kconfig: Adds CONFIG_NET_LOOPBACK_PKTSIZE option
* include/nuttx/net/netconfig.h: Assures that the packet size that is used is at least as large as the largest packet size of other link layer protocols.
* drivers/net/loopback.c: Use that larger packet size.
* boards/sim/sim/sim/configs/tcploop/defconfig: Set the loopback packet size to 1500
Here is the email loop talk about why it is better to remove the option:
https://groups.google.com/forum/#!topic/nuttx/AaNkS7oU6R0
Change-Id: Ib66c037752149ad4b2787ef447f966c77aa12aad
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Squashed commit of the following:
net/netlink: Mark netlink support as EXPERIMENTAL.
net/netlink/netlink_sockif.c: Add netlink_getpeername to the socket interface.
net: Add getpeeername() support for netlink sockets.
include/netpacket/netlink.h: Add a few more definitions and structures used at the NetLink interface. Still missing many.
net/netlink: Add basic framework for Netlink socket support.
include/: Add basic Netlink definitions.
This makes the user interface a little hostile. People thing of an MTU of 1500 bytes, but the corresponding packet is really 1514 bytes (including the 14 byte Ethernet header). A more friendly solution would configure the MTU (as before), but then derive the packet buffer size by adding the MAC header length. Instead, we define the packet buffer size then derive the MTU.
The MTU is not common currency in networking. On the wire, the only real issue is the MSS which is derived from MTU by subtracting the IP header and TCP header sizes (for the case of TCP). Now it is derived for the PKTSIZE by subtracting the IP header, the TCP header, and the MAC header sizes. So we should be all good and without the recurring 14 byte error in MTU's and MSS's.
Squashed commit of the following:
Trivial update to fix some spacing issues.
net/: Rename several macros containing _MTU to _PKTSIZE.
net/: Rename CONFIG_NET_SLIP_MTU to CONFIG_NET_SLIP_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_6LOWPAN_MTU to CONFIG_NET_6LOWPAN_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_ETH_MTU to CONFIG_NET_ETH_PKTSIZE. This is not the MTU which does not include the size of the link layer header. This is the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename the file d_mtu in the network driver structure to d_pktsize. That value saved there is not the MTU. The packetsize is the memory large enough to hold the maximum packet PLUS the size of the link layer header. The MTU does not include the link layer header.
Fix a few typo/compilation problems.
net/: Remove all CONFIG_NET_xxx_TCP_RECVWNDO configuration variables. They were used only to initialize the d_recwndo of the network device structure which no longer exists.
net/: Remove the device TCP receive window field (d_recvwndo) from the device structure. That value is no longer retained, but is calculated dynamically.
Remove some dangling references to CONFIG_NET_TCP_RWND_CONTROL.
net/tcp: Take read-ahead throttling into account when calculating the TCP receive window size.
net/tcp: tcp_get_recvwindow() now returns the receive window size directly (vs. indirectly via the device structure).
net/tcp: Remove CONFIG_NET_TCP_RWND_CONTROL. TCP window algorithm is now trigged only by CONFIG_NET_TCP_READAHEAD.
Squashed commit of the following:
wireless/bluetooth: Some small changes that gets to a clean compile by just eliminating some incorrect implementations (still with a lot of warnings. The logic is still incomplete but now not so lethal.
wireless/bluetooth: Restructuring: Connection interfaces should internal to wireless/bluetooth. include/nuttx/wireless/bt_conn.h removed and merged with wireless/bluetooth/bt_conn.h. Several fix to get closer to bt_netdev.c compiling. Need to design some not interfaces and use some existing interfaces to send and receiv packets.
wireless/bluetooth: Some organization with some network device compile errors fixed. Still not even close to compiling.
net/bluetooth: Fix numerous compile issues; Still open design issues with regard to the interface with the Bluetooth stack.
wireless/bluetooth: Create bt_netdev.c with a crude copy of mac802154_netdev.c. Does not not even compile yet.
include/nuttx/net: Add bluetooth.h. Content is not yet correct.
net/netpackets: Add bluetooth.h. Update net/bluetooth to use new socket address definition.
net/bluetooth: Some fixes for initial build.
net/bluetooth: Add initial support for Bluetooth sockets. The initial cut is just the a clone of the IEEE 802.15.4 socket support with name changes.
net/ieee802154: Fix some typos noted when cloning to create net/bluetooth.
Squashed commit of the following:
net/udp: Address most of the issues with UDP write buffering. There is a remaining issue with handling one network going down in a multi-network environment. None of this has been test but it is certainly ready for test. Hence, the feature is marked EXPERIMENTAL.
net/udp: Some baby steps toward a corrected write buffering design.
net/udp: Remove pesky write buffer macros.
Eliminate trailing space at the end of lines.
net/udp: A little more UDP write buffering logic. Still at least on big gaping hole in the design.
net/udp: Undefined CONFIG_NET_SENDTO_TIMEOUT.
net/udp: Crude, naive port of the TCP write buffering logic into UDP. This commit is certainly non-functional and is simply a starting point for the implementatin of UDP write buffering.
net/udp: Rename udp/udp_psock_sendto.c udp/udp_psock_sendto_unbuffered.c.
commit 5b7b6e6e616c475c782e9883ada9f4a3b7cb4e2c
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sun Aug 20 11:13:17 2017 -0600
IEEE 802.15.4 network device: Make same changes as per loopback device so that it will build with PF_IEEE802154 but without 6LoWPAN.
commit d656a98cf8eab2f20e884224b52cd47ec35df4cc
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sun Aug 20 10:31:28 2017 -0600
PF_IEEE802154: More fixes to device registration and to IEEE 802.15.4 loopback driver for PF_IEEE802154 without 6LoWPAN.
commit 866bb9cbb0c5af79734bbd434c07fa2560b6608f
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sun Aug 20 09:58:13 2017 -0600
Network: Reorganize some Kconfig selections.
commit 230b4cb48008cba5fccdafa22340df1d43584829
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sun Aug 20 09:19:53 2017 -0600
Changes to conditional compilation so that PF_IEEE802154 can build without 6LoWPAN
commit d96cbd6520d40590a740f695c4cd72208ce872da
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sun Aug 20 09:17:02 2017 -0600
configs/sim/pf_ieee802154: Disable 6LoWPAN, IPv6, TCP, and UDP. Now things do not build
commit 2a3ab1652a2c95bcfc8be8380fc7cbdcb6472938
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sat Aug 19 08:44:31 2017 -0600
PF_IEEE802154: Finish some missing bind() logic. Add configs/sim configuration for testing.
commit 59be4b846a6e3bfe82087a888e3fdac9c3c414e5
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 19:30:04 2017 -0600
PF_IEEE802154: More renaming to decouple 6LoPAN from radios in general.
commit 69fabb1aea76e54381bdc13de28a3f1441fb42f4
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 19:21:11 2017 -0600
PF_IEEE802154: Missed a few renamings.
commit ff0af1bb25567720934cc1c2a721ccd92cc35f89
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 17:46:58 2017 -0600
PF_IEEE802154: A few bugfixes
commit 01c7c84afd00cf907d280d30cfaf0fb2cf90e02e
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 17:01:31 2017 -0600
PF_IEEE802154: A few bugfixes
commit dcef4056d1c1488c93151135f3b7106977faa903
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 16:31:05 2017 -0600
PF_IEEE802154: Bring in framework for sendto/recvfrom. Currently just a crude port of functions from net/pkt and do not provide the implemenation needed.
commit 68c5b7b6dd3ab7eb2d0c19890abb38e6561b140e
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 15:18:31 2017 -0600
Trivial fix to typo in comment
commit fd0af534c089569ccdbd59f13b85453de0a653ad
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 15:07:20 2017 -0600
PF_IEEE802154: Add device lookup logic; Rename some things that used to be used only by 6LoWPAN but now must be shared with PF_IEEE802154 and need more generic naming.
commit 4fc80a1659f1c699b050775cefc7f6b631b46114
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 13:49:54 2017 -0600
PF_IEEE802154: Add driver poll logic.
commit d83f71992df8764faa93f9425f1a7602a758f730
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 13:28:59 2017 -0600
PF_IEEE802154: Add frame input function.
commit 77561b8c4d5d7be1f8d8eb62cf1a07229afe2048
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 12:46:29 2017 -0600
PF_IEEE802154: Socket type should be SOCK_DGRAM. Hook in socket interface.
commit c0f90350282e9905d7f26a1b30f04cc6d6794648
Merge: 8b518abfd0 169c55e546
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 09:36:32 2017 -0600
Merge remote-tracking branch 'origin/master' into pf_ieee802154
commit 8b518abfd07d492f5148f2c5fdf65604de9822da
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 09:35:39 2017 -0600
PF_IEEE802154: Add initialization and connection management logic.
commit 98b62620b3cb420041d8ad14204f9410a8aace8c
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 07:52:51 2017 -0600
PF_IEEE802154: Add basic build support and socket interface framework.
