Author: Alan Carvalho de Assis <acassis@gmail.com>
Check all .c and .h against nxstyle and fix it.
Author: Alin Jerpelea <alin.jerpelea@sony.com>
fs: smartfs: Fix over capacity write
When the remaining capacity of flash is one sector, if a new root
directory is created by file open, then the root directory's chain is
broken and it causes to SmartFS filesystem crash. Once this fatal
problem occurs, it's impossible to recover even if the system reboot.
Fix it by finally update link of root directory.
fs: smartfs: Fix buffer overrun
fs: smartfs: Fix uninitialized variable warnings
fs: smartfs: Memory leak fix
boards: cxd56xx: Update spresense board.h
- Fix PMIC assignment
- Add specific pin configurations for spresense
- Remove unnecessary definitions
arch: cxd56xx: Add ITM syslog init at startup
arch: cxd56xx: Enable DMA settings dynamically
Author: Alan Carvalho de Assis <acassis@gmail.com>
Verify all .c and .h against nxstyle, fixed the Mixed cases
Author: Alin Jerpelea <alin.jerpelea@sony.com>
cxd56xx improvements (#48)
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
Run all .c and .h files in last PR through nxstyle.
Author: 脚蹬破拖鞋 <happypapa@yeah.net>
Add Imxrt usdhc insert or remove detection (#43)
* Add usdhc card insertion and removal detection using interrupt for imxrt.
* Add interrupt handle when usdhc insert or remove.
This commit fixes a compilation error that occurs when enabling the
following configuration items for stm32f7 and stm32h7 architectures:
CONFIG_DEBUG_FEATURES=y
CONFIG_DEBUG_ERROR=y
CONFIG_DEBUG_WARN=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_IRQ=y
CONFIG_DEBUG_IRQ_ERROR=y
CONFIG_DEBUG_IRQ_WARN=y
CONFIG_DEBUG_IRQ_INFO=y
The compiler error for stm32f7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:497:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_FIRST'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_FIRST
chip/stm32_irq.c:497:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
And the compiler error for stm32h7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'stm32_dumpnvic':
chip/stm32_irq.c:164:4: warning: #warning Missing logic [-Wcpp]
# warning Missing logic
^~~~~~~
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:522:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_CRS'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_CRS
chip/stm32_irq.c:522:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
This commit replaces all STM32_IRQ_NIRQS defines with the NR_IRQS
define, which seems to be consistent with the rest of the code in
Nuttx.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix long line comments in the header files
Author: Mateusz Szafoni <raiden00pl@users.noreply.github.com>
* arch/arm/src/nrf52: add GPIOTE and SAADC registers definitions
* arch/arm/src/nrf52: update some registers definitions
* arch/arm/src/nrf52: add basic I2C support
* arch/arm/src/nrf52: add function to unconfigure GPIO
* arch/arm/src/nrf52/nrf52_lowputc: add missing FAR
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix stm32l4_otgfshost.c: error: 'ret' undeclared (#32)
result by commit 6a3c2aded6
Change-Id: I68ba79417d8da102da8d91c74496961aef242dd9
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Run all .c and .h files in last PR through tools/nxstyle and fix all complaints.
Author: macman88 <jjlange91@gmail.com>
LPC17xx serial updates (#29)
* Save CONFIG_ARCH_BOARD_CUSTOM when running 'make savedefconfig'
* Don't compile up_earlyserialinit if USE_EARLYSERIALINIT is not defined
* Added support for RS485 direction control on LPC17xx UART1
* First pass at fractional baud rate divider on LPC17xx/40xx
* Added support for fractional divider to console UART
Author: patacongo <spudarnia@yahoo.com>
arch/arm/src/imxrt/imxrt_enet.c: Fix some warnings found in build testing.
Also fix coding standard problems reported by nxstyle. (#26)
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files in last PR through nxstyle.
Author: macman88 <jjlange91@gmail.com>
SAME5x Ethernet Support (#25)
boards/arm/samd5e5/same54-xplained-pro/: Adds basic support for Microchip SAM E54 Xplained Pro board.
arch/arm/src/samd5e5/: Adds an Ethernet driver for the SAME5x family (based on the SAMA5 GMAC driver).
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Minamiya_Natsuki <yukihiratype2@gmail.com>
Add FMC SDRAM for STM32H7x3 chip (#22)
* Add FMC SDRAM for STM32H7x3 chip
* Add FMC SDRAM for STM32H7x7
* Nuttx Coding Standard requires one declaration per line
* should be __ARCH_ARM_SRC_STM32H7_STM32_FMC_H
* fix bad alignment
* fix typo
* fix typo
* people can't live in furture
* fix comment line length
* fix more comment line length
* fix aligenment
* fix typo
arch/arm/src/sama5/sam_serial.c: uart2port in sam_serial, fix the rest of the uarts in sam_serial
boards/arm/sama5/sama5d2-xult/README.txt: Fix some minor typos
boards/arm/sama5/sama5d2-xult/include/board.h: Update UART pin disambiguation with default UARTn_RXD, _TXD
STM32L4_NUSART was set to 4. The spec at
https://www.st.com/resource/en/datasheet/stm32l433cc.pdf states the
following on page 1:
- 4x USARTs (ISO 7816, LIN, IrDA, modem)
- 1x LPUART (Stop 2 wake-up)
However it on page 49, it states:
The STM32L433xx devices have three embedded universal synchronous
receiver transmitters (USART1, USART2 and USART3).
The latter is correct.
This patch sets STM32L4_NUSART to 3.
Code was flawed in that the Pins are defined with the
pullups in the definition. Since there are no alterntes pins
there is no way to remove them. So not enabling the CONFIG
pull up did nothing as did enabling them.
Code also ignored the use of D0 for ready detection causing
3X+ the chatter.
This is now a compile time feature as there was no reason for
it to be a run time. It wasted both flash and ram.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Ran nxstyle against many of the affected files. But this job was too big for today. Many of the network drivers under arch are highly non-compiant and generate many, many faults from nxstyle. Those will have to be visited again another day.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
This effects all network drivers as well as timing related portions of net/: devif_poll_tcp_timer shouldn't be skipped in the multiple card case. devif_timer will be called multiple time in one period if the multiple card exist, the elapsed time calculated for the first callback is right, but the flowing callback in the same period is wrong(very short) because the global variable g_polltimer is used in the calculation. So let's pass the delay time to devif_timer and remove g_polltimer.
nrf52 updates
board/arm/nrf52/nrf52832-dk: use the on-board virtual COM pins as default UART0 configuration
board/arm/nrf52: initial support for the nrf52840-dk board
board/arm/nrf52: initial support for the nrf52840-dk dongle board
arch/arm/src/nrf52: add support for port 1 GPIO
arch/arm/src/nrf52: initial support for UART1
arch/arm/src/nrf52: add UICR definitions
Approved-by: Gregory Nutt <gnutt@nuttx.org>
