Currently Nuttx doesn't seem to be any real support for OTG.
In the future when OTG is supported. This Knob can be removed
and drivers can enable their pin sets based on CONFIG_OTG.
(Adding CONFIG_OTG at this time would be misleading.)
stm32f7:SDMMC Use inttypes in printing macro
stm32f7:CAN Use inttypes in printing macro
stm32f7:DMA Use inttypes in printing macro
stm32f7:serial fix compile error from UNUSED() change
Summary:
- This commit adds stack coloration for the idle task
Impact:
- rp2040 with CONFIG_STACK_COLORATION=y
Testing:
- Tested with nsh, nshsram and smp configurations
- NOTE: CONFIG_STACK_COLORATION=y needs to be added
Summary:
- The NuttX for raspberrypi-pico boots via the boot_stage2 provided
by the pico-sdk which sets the MSP at the end of the SRAM.
- However, the NuttX expects the MSP is set to the top of the idle stack.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with nsh, nshsram and smp configrations
Summary:
- SP_SECTION was introduced to allocate spinlock in non-cachable
region mainly for Cortex-A to stabilize the NuttX SMP kernel
- However, all spinlocks are now allocated in cachable area and
works without any problems
- So SP_SECTION should be removed to simplify the kernel code
Impact:
- None
Testing:
- Build test only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- The CONFIG_SMP_IDLETHREAD_STACKSIZE was introduced to optimize
the idle stack size for other than CPU0
- However, there are no big differences between the idle stacks.
- This commit removes the config to simplify the kernel code
Impact:
- All SMP configurations
Testing:
- Tested with ostest with the following configs
- spresense:smp, spresense:rndis_smp
- esp32-devkitc:smp (QEMU), maix-bit:smp (QEMU)
- sabre-6quad:smp (QEMU), sabre-6quad:netnsh_smp (QEMU)
- raspberrypi-pico:smp, sim:smp (x86_64)
Signed-off-by: Masayuki Ishikawa <asayuki.Ishikawa@jp.sony.com>
stm32h7:Serial Use Idel to poll RX DMA
stm32h7:Serial Do not loop in an ISR!
stm32h7:Serial signal txdma completion with semaphore
stm32h7:Serial Apply formatting suggestions from code review
Co-authored-by: Mateusz Szafoni <raiden00pl@gmail.com>
stm32h7: Serail Add Power Managment (Untested)
arch: Allocate the space from the beginning in up_stack_frame
and modify the affected portion:
1.Correct the stack dump and check
2.Allocate tls_info_s by up_stack_frame too
3.Move the stack fork allocation from arch to sched
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
For unknown reasons this message may interferre with the calibration
procedure and result in invalid calibariton data.
We leave only a message informing about the end of the the calibration.
The problem was observed for STM32G4 + IHM16M1.
Change the logic for allocating user heap for PROTECTED_BUILD:
- Don't rely on SRAM1_END alignment
- Make better use of MPU subregions when allocating the heap
- Don't duplicate the calculation of user heap start in kernel heap
allocation; use the previous calculation directly
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
