arch/arm/src/lc823450: Fix up_allocate_heap() in lc823450_allocateheap2.c
For lc823450, heap area in flat build mode must start just after
_eronly. Because bss/data area is allocated in lower address than
text area in SRAM. See ld.scripts for details. Also, this change
removes unsed up_allocateheap.c
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
Pull request for mtd/progmem refactoring.
* mtd/progmem: change up_progmem_npages to up_progmem_neraseblocks
page is a unit for read/write operation.
eraseblock is a unit for erase operation.
up_progmem_npages is a little bit confusing because it returns number of
erase blocks in flash memory. This patch changes up_progmem_npages to
up_progmem_neraseblocks. There is no logical change.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_erasesize.
Change argument name to be more readable.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_eraseblock
Change up_progmem_erasepage to up_progmem_eraseblock.
eraseblock is more readable name than erasepage.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: change up_progmem_eraseblock's return value.
up_progmem_eraseblock erase a block. so it's better to return the erase block
size than page size.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/cortex-r : fix wrong cp15_flash_dcache.
change mcrne to mcr for unconditional dcache.
Signed-off-by: sungduk.cho <sungduk.cho@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
kinetis:i2c On faild reset re-init i2c and clocking
If a reset fails, we still must reinitializes the
i2c block so that subsequent transfers will not
cause a hardfault due to the clock being off.
If that transfer fails it can try to reset
again.
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/lpc43xx: Fix ethernet TX_EN pin definitions
TX_EN on LPC43xx can be routed via P0.1 and PC.4 in both
MII and RMII mode.
Before, P0.1 was hardcoded for MII and PC.4 was hardcoded for RMII.
Also, the definitions used inconsistent naming (TXEN vs. TX_EN).
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/lpc43xx: Make WWDT usable again
LPC43xx WWDT driver was not updated when irq_dispatch grew an argument
flag in b3222bbc8a.
Also fixes two typos and a naming inconsistency (WWDT vs. WWDG).
Approved-by: GregoryN <gnutt@nuttx.org>
Pull request for cortex-r4 codes
* arm/armv7-r: Add general interrupt controller.
This is based on armv7-a gic controller code.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/armv7-r: add invalidate dcache in arm_head.S
Adding invalidate dcache as a comment in arm_head.S.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/armv7-r: Fix some wrong configuration of program status register.
PSR_E_BIT bit should be set for big endian system.
PSR_A_BIT bis is set automatically as arm cortex-r4 reference manual 3.7.4.
So we don't need to set this bit.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/armv7-r: Fix some wrong MPU register definition.
Change MPU_RBAR_ADDR_MASK and MPU_RACR_TEX_SHIFT mask as
arm cortex-r4 reference manual.
Region Base Address Register 0-4 bits are reserved.
MPU Region Access control register type 3-5 bits.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* driver/mtd: fix compilation error.
This commit fixes below compilation errors.
CC: mtd/smart.c
mtd/smart.c:182:22: error: 'gWearBitToLevelMap4' defined but not used [-Werror=unused-const-variable=]
static const uint8_t gWearBitToLevelMap4[] =
^~~~~~~~~~~~~~~~~~~
mtd/smart.c:170:22: error: 'gWearLevelToBitMap4' defined but not used [-Werror=unused-const-variable=]
static const uint8_t gWearLevelToBitMap4[] =
^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[1]: *** [smart.o] Error 1
Signed-off-by: Junyeon LEE <junyeon2.lee@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
drivers/serial/uart_16550.c: Add a configuration, analogous to the STM32 configuration option, to suppress the NuttX standard re-ordering for /dev/ttySN for special case of the 16550 UART.
config/serial: UART 16550: Add CONFIG_SERIAL_UART_ARCH_MMIO option so the a memory mapped device doesn't need to provide uart_getreg() and uart_putreg() implementations.
u16550_txempty() should check UART_LSR_TEMT to avoid some data left in the transmit FIFO
kinetis:i2c ensure timeout on bus error
The code had a dead wait on I2C_S_BUSY. Noise on the
bus would cause the driver to hang.
Add timeout on invalid states of I2C_S_BUSY to allow
the upper layers do deal with restart or abort.
Approved-by: GregoryN <gnutt@nuttx.org>
Author: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/kinetis: Cosmetic changes from review of coding standard.
Author: David Sidrane <david_s5@nscdg.com>
Merged in david_s5/nuttx/master_kinetis (pull request #710)
kinetis:Add DMA and use it as RX FIFOs on Serial
* Add initial implementation of the DMA
* Add across Kxx family support [WIP]
* Incorporate the DMA into the serial
Add polling to serial
do DMA initialisation at UART startup and fix DMA mux setting.
Fix circular DMA handling in the serial driver.
* Adapt defconfig to enable UART1,4 RXDMA
* [WIP] - refactor this with new CONFIG DMA settings
* kinetis/Kconfig:Bring inline with upstream stucture
1. Use the Serial console configuration from drivers/serial/Kconfig
and friends.
2. Prefix arch specific featurs as such
UARTx_RXDMA->KINETIS_UARTx_RXDMA
* Kinetis:Serial formatting and clean up
* kinetis:DMA Formating and Cleanup
* kinetis:serial Use cleaner DMA API
* kinetis:Make.defs fix duplicate/errant kinetis_dma.o
* kinetis:serial Fix warning/error on only one uart using DMA
The driver can support no DMA on any UART, DMA on some
UARTs or DMA on all UARTs.
In the case of no DMA we disable the DMA based variables
and logic. In the case of all DMA we disable the non
DMA variables and logic, and in the mixed case both
DMA and non DMA variable and logic are enabled.
* kinetis:dma config fix formatting
* kinetis:chip/dma fix formatting
* kinetis:DMA config assume Unknown
Assume KINETIS_DMA_VERSION_UKN for all SoC not versioned
This is as the code was in nuttx prior to this commit
* kinetis:DMAMUX contain versioning- use HAS pattern define Unknown
The pattern for chip versioning is to define 'HAS' constants.
Define KINETIS_DMAMUX_HAS_MONOTONIC_CHCFG to contain the
version numbers to the include soc header and use that define
in the chip headers.
Define the KINETIS_DMAMUX_VERSION_UKN for the default as prior
this commit addressing was by default monotonic for CHCFG
* freedom-k66f:Disable Serial RXDMA
The application has to add calling of the kinetis
serial dma poll as it is application specific.
Approved-by: GregoryN <gnutt@nuttx.org>
* kinetis:PIT add Liftime and Chaining
* kinetis:flexcan fix dup line and ordering
* kinetis:kinetis_lowput.c LPUART data format with parity fix
The 9-bit data mode is typically used with parity to allow
eight bits of data plus the parity
* kinetis:pindma fix warning
* kinetis:lowputc LPUART_BAUD_INIT has to be defined
build fails with test case enable LPUART0 and make
UART1 console
if HAVE_LPUART_DEVICE is defined then LPUART_BAUD_INIT
has to be defined even if the lpuart is not the console
* kinetis:lpserial fix warning
While this is a good idea and a proper thing to do, it also creates a circular dependency and errors during configuration. RTC depends on STM32_RTC which depends on RTC_EXTERNAL with depends on RTC. No can do.
This reverts commit 714e8c1f9e.
Fix http streaming with lc823450
* arch/arm/src/lc823450: Change C-Buffer under-level control
The under-level setting was changed from 1KB to 55KB.
In previous implementation, the setting can ben changed
by the tx threshold but it is fixed at startup.
Also, check write size and adjust alignment if needed.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/lc823450-xgevk: Change IOB related params for rndis.
Since TCP flow control scheme was changed, HTTP audio streaming
has not been working. These IOB params are not optimized but
HTTP audio streaming now works.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
configs/olimex-stm32-p407: Various changes as necessary to get the new kelf configuration working.
configs/olimex-stm32-p407: Add kernel ELF (kelf) configuration.
This update is required to be serialized to the instruction stream meaning that after this update completes, it takes effect immediately and no exceptions of lower priority than the new boosted priority can pre-empt execution. Because of this erratum, the priority boosting does not take place immediately, allowing the instruction after the MSR to be interrupted by an exception of lower priority than the new boosted priority. This effect is only limited to the next instruction. Subsequent instructions are guaranteed to see the new boosted priority.
This was raised in Bitbucket issue 113 from Vadzim Dambrouski.
Squashed commit of the following:
arch/arm/src/samd5e5/sam_usb.c: USB driver now compiles with some issues.
arch/arm/src/samd5e5/chip/sam_fuses.h: Add fuse definition header file.
arch/arm/src/samd5e5: Bring USB driver in from SAMD2L2.
