As coproc_save/restore only used in context_restore/save.
Use macro instead of function.
Some register use optimize.
Unify with arm/riscv.
Signed-off-by: zhuyanlin <zhuyanlin1@xiaomi.com>
The current SAMv7 PWM driver assumes that all PWM channels should
work in sync mode, but that is a partial case of a generic PWM
driver operation.
Start SAMv7 PWM channels in async mode. The sync mode should be
implemeted either using ioctl command or via a separate Kconfig
option.
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- I noticed that rv-virt:knsh64 crashes when it executes the init.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with rv-virt:knsh64
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
1. Add vbat mode for chip internal voltage sample;
2. Add adc channel config;
3. Using DFIFO2 to get the sample value, follow telink sdk.
4. Add calibration function and config;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
The FPU register saving upon vfork entry was missing.
Also added macro that tells the actual size of an FPU reg, instead
of just having a coefficient for qfpu/no-qfpu.
- Remove most of the ifeq-conditions and replace them with variables.
- Move the -I flag for 3rd party headers to opensbi/Make.defs
This clean-up / generalization makes it much simpler to add a new SBI
implementation, without the need to add a bunch of ifeq / elif conditions
to the makefile.
Let the user pick what runs on the harts. For example, the
default configuration now supports NuttX on hart2 and Linux
kernel on harts 3 and 4. Also fix a few issues in the code.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
g_mpfs_ack_sig and g_mpfs_rx_sig are better used with
SEM_INITIALIZER(0) (signalling) rather than with
SEM_INITIALIZER(1) (mutual exclusion).
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Number of channels are now set based on enabled modules (channels) in
configuration instead of the usage of static 4.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Number of channels are now set based on enabled channels in configuration
instead of the usage of static 4.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
