Port C was not working because the GPIO pin count was
wrong. The 48 pin packages has 34 GPIO (Not counting PH0 & PH1)
It is GPIOA GPIO B (sans PB11) and GPIOC PC13-PC15
Summary:
- This commit introduces SP_WFE() and SP_SEV() to be used for spinlock
- Also, use wfe/sev instructions for ARMV7-A to reduce power consumption
Impact:
- ARMV7-a SMP only
Testing:
- sabre-6quad:smp (QEMU, dev board)
- maix-bit:smp, esp32-devkitc:smp, spresense:smp sim:smp (compile only)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
arch/arm/src/stm32/hardware/stm32_spi.h:
* Avoid numerous ifdef on STM32 part numbers and make the
different variations of SPI peripheral features more
self-documenting: based on STM32_HAVE_IP_SPI_V* defines
from chip.h, define some or all of HAVE_SPI_I2S,
HAVE_SPI_TI_MODE, HAVE_SPI_ARB_DATA_SIZE, HAVE_SPI_FIFOS,
HAVE_SPI_NSSP, HAVE_SPI_I2S_ASTRT, and make decisions on
which registers and bitfields to define based on them.
* Define registers and bitfields for STM32_HAVE_IP_SPI_V4,
currently used only for STM32G47XX family MCUs, including
SPI_CR1_CRCL, SPI_CR2_NSSP, SPI_CR2_FRXTH, SPI_CR2_LDMARX,
SPI_CR2_LDMATX, SPI_CR2_DS_SHIFT/SPI_CR2_DS_MASK,
SPI_SR_FRLVL_SHIFT/SPI_SR_FRLVL_MASK, and
SPI_I2SCFGR_ASTRTEN.
* SPI_I2SCFGR_I2SSTD_PHILLIPS: Was defined incorrectly as
(xx << SPI_I2SCFGR_I2SSTD_SHIFT). Corrected this to
(0 << SPI_I2SCFGR_I2SSTD_SHIFT).
* SPI_I2SCFGR_I2SSTD_MSB: Was defined incorrectly as
(0 << SPI_I2SCFGR_I2SSTD_SHIFT). Corrected this to
(1 << SPI_I2SCFGR_I2SSTD_SHIFT).
* Fix nxstyle errors.
arch/arm/include/stm32/chip.h:
* Add new section "Peripheral IP versions" and specify version of
SPI IP block for STM32F10XX, STM32F20XX, STM32F30XX, STM32F33XX,
STM32F37XX, STM32F4XXX, STM32G47XX, and STM32L15XX.
Summary:
- This PR fixes style violations for lc823450.
- NOTE: I will fix more style violations in separate PR later.
Impact:
- No impacts.
Testing:
- I checked build test only.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
- Add new functions of GNSS
- Support the lower PWM frequency
- Add CONFIG_CPUFREQ_RELEASE_LOCK
- Add high speed ADC support
- Add HPADC input gain configuration
- Add eMMC device
- Frame buffer support
- Fix SD/GNSS/sensor drivers not worked
- Build errors
- Fix nxstyle issues
The QuickFeather board added as an initial target.
These featrues are minimally implemented:
* Clock Configuration -- All clocking registers are defined and
configuration is used to setup the HSO, M4 Core, and M4 Perif
clocks. Additionally some clock debugging is stubbed for
bringing out clock paths to IO pins.
* UART -- The lowputc as well as the serial driver is implemnted
for the single UART device. Currently the configuration is
hard coded, but uses the proper interfaces to later fill in.
* SysTick -- The system tick timer is implemented and clocking
properly. Tickless mode is not yet implemented.
* Interrupts -- The interrupt system is implemented and verified
using the UART and SysTick systems.
* GPIO -- GPIO and IOMUX systems are defined and implemented.
This is verified using the UART as well as the Arch LED
system. The GPIO interupt system is stubbed out but not
implemented.
* Arch LEDS -- The blue LED as part of the RGB LED is configured
and attached to the Arch LED system. This indicates the device
coming online as well as when a hardfault is triggered.
Applications and Testing:
* There is a nsh configuration implemented that includes debug
features as well as the ostest, getprime, and mem test.
All of these have been run and verified.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
- Typos / wrong names in s32k14x_irq.h, s32k1xx_memorymap.h and s32k1xx_pcc.h
- Wrong base address for port input disable register in s32k1xx_pin.c
- up_* still had to be changed to arm_* in some places
like other related macro(e.g. INTMAX_MIN, INTMAX_MAX...)
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I8863599960b1a9b1c22ae9c35735a379a4c745b0
Add support for the STM32G474 family of microcontrollers and the
B-G474E-DPOW1 Discovery Board, which features a STM32G474RET6.
This is a major pull request as it adds support for an entirely
new family of STM32. This support is implemented in
arch/arm/src/stm32 and shares implementation with other STM32
families supported by that code, such as the 'L15xx, 'F10xx,
'F20xx, 'F3xxx, and 'F4xxx.
arch/arm/Kconfig:
arch/arm/include/stm32/chip.h:
arch/arm/include/stm32/irq.h:
arch/arm/src/stm32/Kconfig:
arch/arm/src/stm32/hardware/stm32_adc.h:
arch/arm/src/stm32/hardware/stm32_adc_v2.h:
arch/arm/src/stm32/hardware/stm32_dma.h:
arch/arm/src/stm32/hardware/stm32_dma_v1.h:
arch/arm/src/stm32/hardware/stm32_flash.h:
arch/arm/src/stm32/hardware/stm32_i2c.h:
arch/arm/src/stm32/hardware/stm32_i2c_v2.h:
arch/arm/src/stm32/hardware/stm32_memorymap.h:
arch/arm/src/stm32/hardware/stm32_pinmap.h:
arch/arm/src/stm32/hardware/stm32_tim.h:
arch/arm/src/stm32/stm32_allocateheap.c:
arch/arm/src/stm32/stm32_dma.c:
arch/arm/src/stm32/stm32_dma_v1.c:
arch/arm/src/stm32/stm32_dumpgpio.c:
arch/arm/src/stm32/stm32_gpio.c:
arch/arm/src/stm32/stm32_gpio.h:
arch/arm/src/stm32/stm32_lowputc.c:
arch/arm/src/stm32/stm32_rcc.c:
arch/arm/src/stm32/stm32_rcc.h:
arch/arm/src/stm32/stm32_serial.c:
arch/arm/src/stm32/stm32_syscfg.h:
arch/arm/src/stm32/stm32_uart.h:
* Add architectural support to existing NuttX files. This
makes the STM32G474 family parts accessible to the system.
With big thanks for detailed code review:
David Sidrane (davids5)
Mateusz Szafoni (raiden00)
Abdelatif Guettouche (Ouss4)
Add support for the STM32G474 family of microcontrollers and the
B-G474E-DPOW1 Discovery Board, which features a STM32G474RET6.
This is a major pull request as it adds support for an entirely
new family of STM32. This support is implemented in
arch/arm/src/stm32 and shares implementation with other STM32
families supported by that code, such as the 'L15xx, 'F10xx,
'F20xx, 'F3xxx, and 'F4xxx.
arch/arm/include/stm32/stm32g47xxx_irq.h:
arch/arm/src/stm32/hardware/stm32g474cxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474mxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474qxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474rxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474vxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g47xxx_gpio.h:
arch/arm/src/stm32/hardware/stm32g47xxx_memorymap.h:
arch/arm/src/stm32/hardware/stm32g47xxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g47xxx_pwr.h:
arch/arm/src/stm32/hardware/stm32g47xxx_rcc.h:
arch/arm/src/stm32/hardware/stm32g47xxx_syscfg.h:
arch/arm/src/stm32/hardware/stm32g47xxx_uart.h:
arch/arm/src/stm32/stm32g47xxx_rcc.c:
* New files required for architectural support. Note that
existing NuttX files are not modified. As such, in this
revision, the system is unaffected by their addition.
With big thanks for detailed code review:
David Sidrane (davids5)
Mateusz Szafoni (raiden00)
Abdelatif Guettouche (Ouss4)
Move the logic to get TLS information from an inline function to a normal function. For the unaligned case, it is probably too large to be inlined.
Also fixes some minor things from review of previous commits.
In a fit of confusion, I accidentally committed PR 879 before it passed its nxstyle check (it did pass all of its build tests, but not the style check). It was really my intention to merge PR878, but I screwed that up and merged 879 instead.
This PR makes amends by passing all of the .c and .h files modified by PR879 through nxstyle and correcting all reported style problems.
1. Add dsp extension; float point based on hardware and software.
2. Delete folder "iar"
3. Add tool chain for cortex-M23 and cortex-M35p
Signed-off-by: qiaowei <qiaowei@xiaomi.com>
Change-Id: I5bfc78abb025adb0ad4fae37e2b444915f477fe7
