Busy waiting in w25qxxxjv_erase_sector() was without nxsig_usleep and
was causing the entire system to freeze for significant amount of time
as sector erase takes some time.
This commit adds nxsig_usleep into busy waiting to prevent system lock.
Sleep is set to sector erase time based on W25Q series datasheet.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
In previous versions, during the teardown phase, the "open_blockdriver" would call the "mtd proxy" causing the "file mtd" node to be registered in the ftl. " node is registered in ftl.
Therefore, we changed the behavior to find the corresponding inode by node name.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
W25QxxxJV NOR memories are backward compatible with older Winbond´s
generations and thus can also be supported here. This essentially brings
the support for generic SPI to W25QxxxJV memories as w25qxxxjv.c file only
supports QSPI communication.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
1.support to use dd commond to burn romfs image to nand flash
2.support bare-write nand flash device without file system
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
Directly return -ENOTTY in rpmsgxxx_ioctl() when the command is
not supported to avoid fdsan command FIOC_SETTAG and FIOC_GETTAG
pass to the rpmsg dev/mtd/blk server with CONFIG_FDSAN enabled.
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
1 Gbit W25Q01JV flash uses two 512 Mbit dies. This requires specific
operations in the driver in order to support the entire 1 Gbit region.
This commit adds dual die support for W25Q01JV flash.
Generally the driver has to switch active dies when die specific read from
status register is required (therefore before read, write, erase and when
checking if write status register was successful).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
W25QXXXJV_WRITE_STATUS_2 register uses just first byte therefore all
operations has to be done in priv->cmdbuf[0]. Previous priv->cmdbuf[1]
caused QuadSPI mode not being enabled.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
follow how Linux report the correction information from ecc:
http://www.infradead.org/pipermail/linux-mtd/2012-March/040305.html
since this information is very useful to file system(e.g. yaffs, ubi/buifs)
which is specially designed for nand flash.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Since not all nand devices follow ONFI spec, nand_raw_initialize could be used to skip ONFI special action
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
