SiFive document: "ECC Error Handling Guide" states:
"Any SRAM block or cache memory containing ECC functionality needs to be
initialized prior to use. ECC will correct defective bits based on memory
contents, so if memory is not first initialized to a known state, then ECC
will not operate as expected. It is recommended to use a DMA, if available,
to write the entire SRAM or cache to zeros prior to enabling ECC reporting.
If no DMA is present, use store instructions issued from the processor."
Clean the cache at this early stage so no ECC errors will be flooding later.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Check that the base address and region size are properly aligned with
relation to each other.
With NAPOT encoding the area base and size are not arbitrary, as when
the size increases the amount of bits available for encoding the base
address decreases.
Implement the previously empty mpfs_ddr_rand with adapted "seiran128" code
from https://github.com/andanteyk/prng-seiran
This implements a non-secure prng, which is minimal in size. The DDR training
doesn't need cryptographically secure prng, and linking in the NuttX crypto
would increase the code size significantly for bootloaders.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Also move the DDRC clock enablement and reset to mpfs_init_ddr. This doesn't
change the functionality, but is the cleaner place for it.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Especially the write calibration must bail out if the memory test timeouts,
otherwise the device will get stuck in running the memory test in sequence,
and it will always timeout.
Negative error value was also not properly returned from mpfs_mtc_test.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
It doesn't make sense to try to auto-determine write latency, it may pass with too low value.
Keep the existing implementation if the write latency has been set to minimum
value, otherwise just set it.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Current implementation of QSPI in SPI mode was available only for MCUs
that do not have standard SPI at all. MCUs with both QSPI and SPI can
however also use QSPI in SPI mode and thus have one more SPI bus. This
commit adds required defines and config options to support QSPI in SPI
mode for all SAMv7 MCUs.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Calculate how long an I2C transation will take in microseconds, and use
this as the timeout for mpfs_i2c_sem_waitdone.
The reason for doing this is not to keep an i2c bus reserved for the full
1 second timeout, if e.g. a sensor is not on the bus / is faulty and
non-responsive. Reading the other sensors will be blocked for a relatively
long time (1 second) in this case. This fixes such behavior.
This commit adds function pwm_set_polarity() that setups channel
polarity based on input info from application layer.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Pinephone Pro port just nsh
Status:
booting till GICD / IRQ issue
style cleanups
start to fix style checks
revert offset
whitespaces
revert a64 bringup file
prob last cleanup
more cleanups
remove dts
move changes from a64 hardware specific folders to rk3399
undo common changes (except head.s)
revert gitignore
missing irq.h and rk3399_serial.c need to finish cleaning them up
WIP
add source for load address
make debug print hex again add board include
Pinephone Pro port just nsh
Status:
booting till GICD / IRQ issue
style cleanups
start to fix style checks
revert offset
whitespaces
revert a64 bringup file
prob last cleanup
more cleanups
remove dts
move changes from a64 hardware specific folders to rk3399
undo common changes (except head.s)
revert gitignore
missing irq.h and rk3399_serial.c need to finish cleaning them up
WIP
add source for load address
remove ccache, add board memory map
remove board reset
1 page might not be enough, if the task has a bigger stack. Best effort
is to allocate the default amount, however this won't work will all
tasks either.
Currently TX_FIFO_SIZE is not altered in mpfs_ep_set_fifo_size(),
but all paths (RX and TX) change MPFS_USB_RX_FIFO_SIZE only.
Fix the TX_FIFO_SIZE setup.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
After sevaral resets of the chip after programming, rptun stops working correctly.
Simple test with RPMSG UART causes a lock:
on the netcore:
nsh>cat /dev/ttyproxy
on the appcore:
nsh>echo xxx > /dev/ttyproxy
The problem doesn't occur with NRF53_FLASH_PREFETCH=n
Summary
this is a old implement for Arm64 trace but will failed
compile when enable CONFIG_SCHED_INSTRUMENTATION_SWITCH
remove it since it will never use for trace framework
Signed-off-by: qinwei1 <qinwei1@xiaomi.com>
after the follow patch:
commit 9aa57b6c53
Author: wangbowen6 <wangbowen6@xiaomi.com>
Date: Wed Mar 22 11:49:43 2023 +0800
virtio: add virtio framework in NuttX
1. virtio devics/drivers match and probe/remote mechanism;
2. virtio mmio transport layer based on OpenAmp (Compatible with both
virtio mmio version 1 and 2);
3. virtio-serial driver based on new virtio framework;
4. virtio-rng driver based on new virtio framework;
5. virtio-net driver based on new virtio framework
(IOB Offload implementation);
6. virtio-blk driver based on new virtio framework;
7. Remove the old virtio mmio framework, the old framework only
support mmio transport layer, and the new framwork support
more transport layer and this commit has implemented all the
old virtio drivers;
8. Refresh the the qemu-arm64 and qemu-riscv virtio related
configs, and update its README.txt;
New virtio-net driver has better performance
Compared with previous virtio-mmio-net:
| | master/-c | master/-s | this/-c | this/-s |
| :--------------------: | :-------: | :-------: | :-----: | :-----: |
| qemu-armv8a:netnsh | 539Mbps | 524Mbps | 906Mbps | 715Mbps |
| qemu-armv8a:netnsh_smp | 401Mbps | 437Mbps | 583Mbps | 505Mbps |
| rv-virt:netnsh | 487Mbps | 512Mbps | 760Mbps | 634Mbps |
| rv-virt:netnsh_smp | 387Mbps | 455Mbps | 447Mbps | 502Mbps |
| rv-virt:netnsh64 | 602Mbps | 595Mbps | 881Mbps | 769Mbps |
| rv-virt:netnsh64_smp | 414Mbps | 515Mbps | 491Mbps | 525Mbps |
| rv-virt:knetnsh64 | 515Mbps | 457Mbps | 606Mbps | 540Mbps |
| rv-virt:knetnsh64_smp | 308Mbps | 389Mbps | 415Mbps | 474Mbps |
Note: Both CONFIG_IOB_NBUFFERS=64, using iperf command, all in Mbits/sec
Tested in QEMU 7.2.2
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
This adds a config flag to remove manual bclksclk training if one wants
to just use the controller's own training.
Manual addcmd training depends on the manual bclksclk training, so this
also adds this dependency in Kconfig.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
(1)common/arm_backtrace_unwind.c:528:18: warning: 'ctrl.lr_addr' may be used uninitialized in this function [-Wmaybe-uninitialized]
(2)common/arm_backtrace_unwind.c:626:27: warning: assignment to 'long unsigned int' from 'uint8_t (*)[]' {aka 'unsigned char (*)[]'} makes integer from pointer without a cast [-Wint-conversion]
Signed-off-by: yanghuatao <yanghuatao@xiaomi.com>
Decreasing the value may increase DQ/DQS window size. Keep the default value
(1) for the existing board configurations.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Adds a platform specific implementation for tickless schedular operation. This includes:
- Tickless operation for vexriscv cores.
- Tickless operation for vexriscv-smp cores.
- Ticked operation for vexriscv-smp cores.
Ticked operation for vexriscv core has been refactored.
Additional default configuration added to demonstrate operation.
Both tickless and ticked options use Litex timer0 for scheduling intervals. This is significantly faster than interfaceing with the risc-v mtimer through opensbi.
Considering kernel code, it's reasonable to use `PANIC()` instead
of `assert(0)` to handle with situations that require abort. Unlike
`assert`, `PANIC()` doesn't dependent on `NDEBUG`.
ESP32-S3 has only one 2.4 GHz ISM band RF module, which is shared
by Bluetooth and Wi-Fi, so Bluetooth can’t receive or transmit data
while Wi-Fi is receiving or transmitting data and vice versa.
Under such circumstances, ESP32-S3 uses the time-division
multiplexing method to receive and transmit packets.
The low-level Wi-Fi driver registers two peripheral interrupts to
the same CPU interrupt. Although the registered ISR is the same for
both peripherals interrupt, it's needed to call `up_enable_irq` to
ensure that the interrupt matrix is being set accordingly.
Please note that the current implementation of the ESP32-S3's IRQ
driver - although allow us to set a callback for each IRQ, which
represents the peripherals interrupt - doesn't allow us to call
both callbacks when these IRQs refers to a same CPU interrupt.
`g_cpu0_intmap` (or `g_cpu1_intmap`) associates each CPU interrupt
to a single IRQ/peripheral and, then, when a CPU interrupt is
triggered, only the last registered IRQ's callback will be called.
This isn't a problem here because 1) the registered callback is the
same for both IRQ's (in fact, it considers the CPU interrupt) and
2) we know in advance which peripheral interrupts will be attached
to which CPU interrupt and, then, we can set them directly.
This prevents us from getting stuck while polling the different
network structures in `devif_poll_connections`. This is useful for
Wi-Fi/Bluetooth coexistence, specifically.
- Fix macro values from `arch/xtensa/include/esp32s3/irq.h`
- Remove references to unexisting edge-triggered CPU interrupts
- Add `esp32s3_getirq` to get IRQ based on core and the `cpuint`
RTC subsystem controls not only the RTC itself but functions that
use RTC-enabled features like Bluetooth and Wi-Fi. Initialization
must be performed during the system start-up.
