For CEVA platform CHAR_BIT is 16, and will do lots of extra work
when use IPC.
We will not support this platform anymore, so remove all the b2c operations.
Signed-off-by: ligd <liguiding1@xiaomi.com>
since the caller is free not to monitor any event
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ib957be1b1b5a686faea0196bc9069e0908a492eb
Summary:
- I thought this cs is needed to avoid data corruption
- For example, while executing uart_xmitchar() in the interrupt
handler on CPU0, an application running on CPU1 can call
uart_putxmitchar() via write()->uart_write().
- In this case, taking xmit.sem in uart_write() will wait for CPU0
to finish uart_xmitchar() because CPU0 has already taken a cs
in uart_xmitchar() then nxsem_wait() on CPU0 takes a new cs
inside (and release the cs when returning but it's OK)
- Then uart_write() on CPU1 disables UART TX, so uart_xmitchar()
on CPU0 will not be called while executing uart_write() on CPU1.
- So this critical section in uart_putxmitchar() can be removed.
Impact:
- None
Testing:
- Tested with spresense:wifi_smp, esp32-devkitc:smp
Reported-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
since the console is normally opened three time as stdin, stdout and
stderr and remove the dependence on STANDARD_SERIAL because other type
of serial drivers also support the poll through the same codebase.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ie68322c4647cc838b295491329969869d6ba310b
This is addressing an issue where Rx interrupts were not restored for
cdcacm after the buffer had been filled (in a burst).
The Rx interrupts were only restored after the watchdog timeout of 200ms
fired.
This happened because CONFIG_SERIAL_RXDMA was set, however, for the
cdcacm driver this does not actually matter as it is relying on
uart_enablerxint to be called via the ops table.
This patch makes sure that uart_enablerxint and uart_disablerxint are
always called, independent of CONFIG_SERIAL_RXDMA, relying on the ops
table to be correct for the case where it should be only a no-op.
Sebastien Lorquet has submitted the ICL and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
serial/serial_dma.c: In function ‘uart_recvchars_done’:
serial/serial_dma.c:407:7: warning: implicit declaration of function ‘nxsig_kill’ [-Wimplicit-function-declaration]
407 | nxsig_kill(dev->pid, signo);
| ^~~~~~~~~~
Change-Id: I9e1c0341ecce3033889d11fff9ec2b9e3dfe303b
user should select the default action by self:
warning: (TTY_SIGINT) selects SIG_SIGKILL_ACTION which has unmet direct dependencies (SIG_DEFAULT)
Change-Id: Ied9899d18156742ce4998b40d53a481262dcd84a
Signed-off-by: ligd <liguiding1@xiaomi.com>
these functions are the implementation detail and then
don't need expose to external
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ief832391d5b42d1f1645907eb465631650490234
let's replace the content of file in place instead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I538910d55815c7aec656c05dba4eab2fa1d6d964
so pty don't need call nx_pipe and then file_detach
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ibb8d108abd76bafe53897e5fca35babcf3e1bae9
Re-check RX queue status after uart_enablerxint() and before blocking
the reading task on the receive semaphore. cdcacm (and maybe other UART
drivers) can push buffered data into the receive queue during
uart_enablerxint(), leading to a blocked task while data is already
available.
Signed-off-by: Tido Klaassen <tido@4gh.eu>
Follow the POSIX description.
SIGTSTP should be sent when the Ctrl-Z characters is encountered, not SIGSTP.
Testing:
Built with hifive1-revb:nsh (CONFIG_SERIAL_TERMIOS=y, CONFIG_SIG_DEFAULT=y and CONFIG_TTY_SIGTSTP=y)
There is a good case on sim platform:
When we input some cmd and click enter key to start application in terminal,
this context will change to application from IDLE loop. Althrough entey key '\r'
has been received to recv buffer and complete post semaphore of reader, but
pollnotify may not be called because context change. So when application run
poll function, because no events happend and poll enter wait, context will
again change to IDLE loop, this pollnotify of IDLE loop will run to send poll
events, poll function of applicaton will wake up. It's wrong!
Change-Id: I812a889f2e90781a9c3cb4b0251cccc4d32bebd1
Signed-off-by: dongjiuzhu <dongjiuzhu1@xiaomi.com>
Reported by 권석근 <kwonsksj@gmail.com>:
I found a bug at "pty.c" during ssh server implementation.
When I turn on CONFIG_SERIAL_TERMIOS and OPOST|ONLCR on pty device
for nsh console's stdin/stdout (ssh shell service), I've got system crash.
Bugs at line 687 of pty.c, pty_write()
ntotal++;
when converting '\n' to '\r\n', pty_write() will return more than requested
(+1, for example) length. and this will break caller lib_fflush(), line 150
of lib_libfflush.c.
When she get (libfflush()) bytes_nwritten which is greater than nbuffer,
nbuffer goes to negative at line 150 and eventually destroys
*stream->fs_bufpos at line 163 of lib_libflush.c
Removing ntotal++; line 687 of pty.c will fix this bug.
BTW, nsh using ptm/pty as a ssh shell service works great with libssh +
mbedtls.