This makes the user interface a little hostile. People thing of an MTU of 1500 bytes, but the corresponding packet is really 1514 bytes (including the 14 byte Ethernet header). A more friendly solution would configure the MTU (as before), but then derive the packet buffer size by adding the MAC header length. Instead, we define the packet buffer size then derive the MTU.
The MTU is not common currency in networking. On the wire, the only real issue is the MSS which is derived from MTU by subtracting the IP header and TCP header sizes (for the case of TCP). Now it is derived for the PKTSIZE by subtracting the IP header, the TCP header, and the MAC header sizes. So we should be all good and without the recurring 14 byte error in MTU's and MSS's.
Squashed commit of the following:
Trivial update to fix some spacing issues.
net/: Rename several macros containing _MTU to _PKTSIZE.
net/: Rename CONFIG_NET_SLIP_MTU to CONFIG_NET_SLIP_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_6LOWPAN_MTU to CONFIG_NET_6LOWPAN_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_ETH_MTU to CONFIG_NET_ETH_PKTSIZE. This is not the MTU which does not include the size of the link layer header. This is the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename the file d_mtu in the network driver structure to d_pktsize. That value saved there is not the MTU. The packetsize is the memory large enough to hold the maximum packet PLUS the size of the link layer header. The MTU does not include the link layer header.
Fix a few typo/compilation problems.
net/: Remove all CONFIG_NET_xxx_TCP_RECVWNDO configuration variables. They were used only to initialize the d_recwndo of the network device structure which no longer exists.
net/: Remove the device TCP receive window field (d_recvwndo) from the device structure. That value is no longer retained, but is calculated dynamically.
Remove some dangling references to CONFIG_NET_TCP_RWND_CONTROL.
net/tcp: Take read-ahead throttling into account when calculating the TCP receive window size.
net/tcp: tcp_get_recvwindow() now returns the receive window size directly (vs. indirectly via the device structure).
net/tcp: Remove CONFIG_NET_TCP_RWND_CONTROL. TCP window algorithm is now trigged only by CONFIG_NET_TCP_READAHEAD.
Squashed commit of the following:
configs/*/README.txt: Replace each occurrence of './configure.sh' with 'tools/configure.sh'
configs/*/README.txt: Remove 'cd ..' after each './configure.sh'
configs/*/README.txt: Remove 'cd -' after each './configure.sh'
configs/*/README.txt: Remove 'cd tools' before each './configure.sh'
configs/README.txt: Remove instruction to CD tools/ before running configure.sh.
ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
net/icmpv6: IPPROT_ICMP6 socket logic now builds without error.
net/icmpv6: Add support for read-ahead and poll(). Initial commit is just cloned from ICMP with the appropriate name changes.
configs/: All defconfig filess that include CONFIG_NET_ICMPv6_SOCKET=y need to select CONFIG_SYSTEM_PING6=y and deselect CONFIG_DISABLE_POLL.
Update NSH documention to show that ping6 is now a built in command.
net/icmpv6: Add icmpv6_sendto.c and icmpv6_recvfrom.c. Initial versions are just clones from icmp/ with appropriate name changes.
net/icmpv6: Clone some ICMP socket logic as the beginning of support for ICMPv6 socket support.
Rename CONFIG_NET_ICMPv6_PING to CONFIG_NET_ICMPv6_SOCKET. Move prototype for icmpv6_ping from include/nuttx/net/icmpv6 to net/icmpv6/icmpv6.h
Squashed commit of the following:
net/icmp: Finishes off icmp_recvfrom().
net/icmp: Add readahead support for IPPROTO_ICMP sockets.
net/icmp: Add poll() support for IPPROTO_ICMP sockets.
net/icmp: Add a connection structure for IPPROTO_ICMP sockets.
net/icmp: Implements sendto for the IPPROTO_ICMP socket.
net/icmp: Move icmp_sendto() and icmp_recvfrom() to separate files. They are likely to be complex (when they are implemented).
net/icmp: Hook IPPROTO_ICMP sockets into network. Fix some naming collisions. Still missing basic ICMP send/receive logic.
configs: apps/system/ping current need poll() enabled.
configs: All defconfig files that use to enable low-level support must now enabled CONFIG_SYSTEM_PING.
net/icmp: Adds basic build framework to support IPPROTO_ICMP sockets.
Squashed commit of the following:
Change all calls to usleep() in the OS proper to calls to nxsig_usleep()
sched/signal: Add a new OS internal function nxsig_usleep() that is functionally equivalent to usleep() but does not cause a cancellaption point and does not modify the errno variable.
sched/signal: Add a new OS internal function nxsig_sleep() that is functionally equivalent to sleep() but does not cause a cancellaption point.
drivers/wireless: Adds XBee S2C (802.15.4 firmware) support. XBee driver emulates mac802154 interface
* drivers/wireless/xbee: Adds xbee_netdev. Very similar to mac802154_netdev
* configs/same70-xplained: Starts adding support for XBee radio
* drivers/wireless/ieee802154/xbee: More structuring of XBee driver
* drivers/wireless/ieee802154/xbee: More Xbee work. Starts adding support on Clicker2
* drivers/wireless/ieee802154/xbee: More XBee MAC code
* configs/clicker2-stm32: More work to add XBee radio support
* drivers/wireless/ieee802154/xbee: Most of driver is now structured. No build errors
* configs/clicker2-stm32: Adjustments to XBee click module support
* drivers/xbee: Changes md_ prefix to xd_ prefix for xbeenet_driver_s fields
* drivers/xbee: XBee network device now passes MAC events via IOCTL
* drivers/xbee: Support querying device for parameters, setting parameters, and structures association/startpan logic
* configs/clicker2-stm32: Fixes Xbee lower half ATTN poll logic
* drivers/xbee: Removes dependce on CONFIG_IEEE802154_NETDEV
* drivers/xbee: Supports MAC RESET.request primitive
* drivers/xbee: Exposes generic AT query to the rest of driver
* drivers/xbee: Sets local values when writing setting change to Xbee device
* drivers/xbee: Finish association logic
* drivers/xbee: Adds xbee_get_mhrlen( ) allocating enough space for API frame header to frame
* drivers/xbee: Finishes transmit/receive logic
* drivers/xbee: Fixes xbee_netdev to match logic in mac802154_netdev.c
* drivers/xbee: Rearranges logic to prevent a loop condition where recursion could potentially occur to the point of deadlocking the system
Approved-by: Gregory Nutt <gnutt@nuttx.org>
