This PR adds the driver for Reduced Serial Bus (RSB) on Allwinner A64 SoC. The RSB Driver will be called by the upcoming Power Mgmt IC Driver for PINE64 PinePhone, to power on the LCD Display.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > RSB" (`CONFIG_A64_RSB`), which enables the RSB Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for RSB
`arch/arm64/src/a64/Make.defs`: Added the RSB Driver to the Makefile
`arch/arm64/src/a64/a64_de.c`: Increase PLL Timeout for Allwinner A64 Display Engine
`boards/arm64/a64/pinephone/configs/nsh/defconfig`: Set PinePhone Board Config `CONFIG_BOARD_LOOPSPERMSEC` to the value computed by `calib_udelay`
`arch/arm64/src/a64/a64_rsb.c`, `a64_rsb.h`: RSB Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added RSB as supported peripheral for PinePhone
This PR adds the driver for Display Engine 2.0 on Allwinner A64 SoC. The Display Engine Driver will be called by the upcoming LCD Driver for PINE64 PinePhone.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > DE" (`CONFIG_A64_DE`), which enables the Display Engine Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for Display Engine
`arch/arm64/src/a64/Make.defs`: Added the Display Engine Driver to the Makefile
`boards/arm64/a64/pinephone/configs/nsh/defconfig`: Removed Scheduler Debug Info (`CONFIG_DEBUG_SCHED_INFO`) from the PinePhone Board Config, because it garbles the Console Output.
`arch/arm64/src/a64/a64_de.c`, `a64_de.h`: Display Engine Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added Display Engine as supported peripheral for PinePhone
This PR adds the driver for TCON0 (Timing Controller) on Allwinner A64 SoC. The TCON0 Driver will be used by the upcoming Display Driver for PINE64 PinePhone.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > TCON0" (`CONFIG_A64_TCON0`), which enables the TCON0 Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for TCON0
`arch/arm64/src/a64/Make.defs`: Added the TCON0 Driver to the Makefile
`arch/arm64/src/a64/a64_tcon0.c`, `a64_tcon0.h`: TCON0 Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added TCON0 as supported peripheral for PinePhone
This PR adds the driver for Allwinner A64's MIPI Display Serial Interface (DSI) and MIPI Display Physical Layer (D-PHY).
This driver will be used by the upcoming Display Driver for PINE64 PinePhone.
- `include/nuttx/crc16.h`: Added 16-bit CRC-CCITT
- `libs/libc/misc/Make.defs`: Added 16-bit CRC-CCITT to Makefile
- `arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > MIPI DSI" (`CONFIG_A64_MIPI_DSI`), which enables the MIPI DSI Driver
- `arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for MIPI DSI
- `arch/arm64/src/a64/Make.defs`: Added the MIPI DSI Driver to the Makefile
- `libs/libc/misc/lib_crc16ccitt.c`: Compute 16-bit CRC-CCITT
- `arch/arm64/src/a64/mipi_dsi.c`, `mipi_dsi.h`: Compose MIPI DSI Packets (Long, Short, Short with Parameter)
- `arch/arm64/src/a64/a64_mipi_dsi.c`, `a64_mipi_dsi.h`: MIPI DSI Driver for Allwinner A64
- `arch/arm64/src/a64/a64_mipi_dphy.c`, `a64_mipi_dphy.h`: MIPI D-PHY Driver for Allwinner A64
- `platforms/arm/a64/boards/pinephone/index.rst`: Added MIPI DSI as supported peripheral for PinePhone
Co-Authored-By: Petro Karashchenko <petro.karashchenko@gmail.com>
This PR adds the drivers for Allwinner A64 PIO (Programmable I/O) and PinePhone LEDs (Red / Green / Blue).
The PIO Driver is based on the NuttX PIO Driver for Allwinner A10: [`arch/arm/src/a1x/a1x_pio.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_pio.c)
- `arch/arm64/src/a64/Make.defs`: Add PIO Driver to Makefile
- `boards/Kconfig`: Add `ARCH_HAVE_LEDS` to PinePhone
- `boards/arm64/a64/pinephone/src/pinephone.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_boardinit.c`: Start Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Start User LEDs
- `boards/arm64/a64/pinephone/src/Makefile`: Add LED Driver to Makefile
- `boards/arm64/a64/pinephone/configs/nsh/defconfig`: Add `CONFIG_USERLED` to `nsh` config
- `arch/arm64/src/a64/a64_pio.c`, `a64_pio.h`: Allwinner A64 PIO Driver
- `arch/arm64/src/a64/hardware/a64_memorymap.h`: PIO Memory Map
- `arch/arm64/src/a64/hardware/a64_pio.h`: PIO Definitions
- `boards/arm64/a64/pinephone/include/board.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_autoleds.c`: Driver for Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_userleds.c`: Driver for User LEDs
- `introduction/supported_platforms.rst`: Add Allwinner A64 as Supported Platform
- `platforms/arm/a64/boards/pinephone/index.rst`: Add PIO and LEDs to PinePhone
Config option IMXRT_ADCx_ETC can now be used to select an external HW
trigger to be used instead of continous trigger. Continous trigger is
used if IMXRT_ADCx_ETC = -1 (default option). Otherwise the source signal
is routed through XBAR and used as a trigger.
Hardware triggering is currently limited to maximum of 8 channels.
HW trigger is automatically disabled if there are more than 8 channels.
The external triggering was tested with PWM signal as a source.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit allows the PWM modules to be synchronized by an external
signal (other PWM module for example). The sync source can be selected
from configuration.
PWM module can also now generate a trigger when its timer reaches the duty
cycle. This trigger is used for the synchronization of other modules. It
can also be used for triggering ADC for example in the future.
Thanks to Rastislav Pavlanin and Jan Spurek from NXP support for
suggestion which helped to solve the inter-module PWM synchronization
task.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This patch adds corrected implementation of FLASH memory to be used
with progmem driver for use with mtd filesystems like nxffs or smartfs.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
This patch adds to the nucleo-wl55jc previously implemented EXTI support.
Button support with nuttx's button driver is added.
I've written small example to show how to use GPIO EXTI. B3 button can be
used (selectable via Kconfig) to toggle Red LED.
I've added new defconfig for demo purposes. I've included there config
and enabled example programs that are meant to demonstrate functions of
the board and does not really have a place in real world project. Like
Red LED can be toggled with B3 button, or LED example that flashes LEDS,
or button example to show which button has been pressed.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- Change (1 << 0) to (1 << BUTTON1_BIT (and similar)
v2 -> v3:
- Fix invalid BUTTON3_BIT value
v3 -> v4:
Suggested by: Petro Karashchenko
- Change 0/1 to false/true
This patch implements working support for EXTI GPIO.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- change (1 << n) to (1 << (n)) in macro definition
- change 1 << X to (1 << X) in code
- fix alignment
v2 -> v3:
Suggested by: Petro Karashchenko
- I was supposed to change (1 << pin) to 1 << pin, not the other way around:)
This patch adds documentation for both stm32wl5 chip family and
nucleo-wl55jc board. I've kept the same directory structure for
arm/stm32 as in arch/ and boards/ directories.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Multiple files were badly formatted, which resulted in many
warnings. This made it harder to check for errors in newly
written documentation.
What's worse, badly formatted text resulted in butchered
output in generated html.
This patch fixes most of the errors, but alas, not all of
the errors can be fixed. Anyway, this should be way easier
to spot errors in newly written docs now.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
