stm32f7: serial: Fix ioctl TIOCSSINGLEWIRE
The TRM notes that UE must be disabled in order to write HDSEL in
USART_CR3. This was not being done, so calls to TIOCSSINGLEWIRE were
silently failing.
This change checks the state of UE in USART_CR1, clears the UE bit
before writing HDSEL, then re-enables it if neccesary.
Approved-by: GregoryN <gnutt@nuttx.org>
drivers/xbee: Fixes issue with timeouts. Timeouts were in ticks but should have been in ms. This caused false triggers of timeout causing redundant packets, etc.
Approved-by: GregoryN <gnutt@nuttx.org>
LTDC fixes
* stm32_ltdc: Allows to use ltdc without overlay support
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32: Removes overlay dependency when LTDC is enabled
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32: Allows to configure initial chromakey for LTDC layer
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32_ltdc: Fixes another compiler warning when dma2d is disabled
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32_ltdc: Checks for register reload is done before continued
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32f429i-disco: Fixes eliminated register control by compiler optimization
When reading 1 byte from the SPI device the clock must be enabled and
immediately disabled. This section has been optimized by the compiler (-O2) to a
missing active spi clock. A subsequently block read failed because of missing
response from the spi device. This has been lead to a broken display
initializing.
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Fixes compiler errors when using LTDC and DMA2D
* stm32: ltdc and dma2d are are depends on FB_OVERLAY support
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32_dma2d.h: Makes interface available when FB_OVERLAY is enabled
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32_ltdc: Fixes compiler error when blit support is disabled
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32f429i-disco: Updates lvgl board example
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
* stm32f429i-disco: Updates nxwm board example
Still nxwm_main is missing.
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Signal handlers maybe run with interrupts enabled or disabled, depending on how the task the received the signal was blocked. (i.e.: If sem_wait() is called, then we disable interrupts, then block the currently running task). This could be dangerous, because user code would be running with interrupts disabled.
This change forces interrupts to be enabled in up_sigdeliver() before executing the signal handler calling up_irq_enable() explicitly. This is safe because, when we return to normal execution, interrupts will be restored to their previous state when the signal handler returns.
stm32f334-disco/buckboost: use a PID controller from libdsp
* libdsp: initial commit
* libdsp: cosmetics
* stm32f334-disco/buckboost: use a PID controller from libdsp
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm/src/stm32/stm32f10xxf30xx_flash.c: Re-implemented Dmitriy Linikov's change to support multi-banked FLASH on the STM32 F1 parts AFTER separating the FLASH support by architecture and implementing more standard base+offset register addressing. Now the change goes in rather cleanly.
arch/arm/src/stm32/stm32f10xxf30xx_flash.c: Use base + offset address to simplify implementation of dual bank flash.
Squashed commit of the following:
arch/arm/src/stm32/stm32f10xxf30xx_flash.c: Be consistent in file naming.
arch/arm/src/stm32l10xxf30xxx_flash.c: Separate STM32F10xx and STM32F30xx FLASH logic into a separate file.
arch/arm/src/stm32l20xx40xxx_flash.c: Separate STM32F20xx and STM32F40xxFLASH logic into a separate file.
arch/arm/src/stm32l15xx_flash.c: Separate STM32L15xx FLASH logic into a separate file.
