If transfer is restarted in irq handler the interrupts shall be
cleared before the start bit is set in control register. This is
to avoid ints being accidentally cleared before they are handled leading
to timeout error.
In spi_irq handler the data is written into txfifo and transfer
is started before the TXDONE interrupt is cleared. If the bus/memory
access is in some cases delayed, the spi transfer may have been
finished already before the interrupt register is cleaned for the
transfer. This leads the early arrived interrupt to be just removed
and never handled, which would cause a timeout error.
This patch moves the clearing of the interrupt to the place before
the tx is started, so the interrupt is not missed in above cases.
The function is not relevant any longer, remove it. Also remove
save_addrenv_t, the parameter taken by up_addrenv_restore.
Implement addrenv_select() / addrenv_restore() to handle the temporary
instantiation of address environments, e.g. when a process is being
created.
Detach the address environment handling from the group structure to the
tcb. This is preparation to fix rare cases where the system (MMU) is left
without a valid page directory, e.g. when a process exits.
NuttX kernel should not use the syscall functions, especially after
enabling CONFIG_SCHED_INSTRUMENTATION_SYSCALL, all system functions
will be traced to backend, which will impact system performance.
Signed-off-by: chao an <anchao@xiaomi.com>
PWM driver for multiple peripherals supplied in gateware.
Only single channel frequency and duty cycle control is implemented. Pulse counting and multichannel features are not currently feasible.
Additions also include a new board configuration for arty-a7 which enables the PWM driver and example application.
This is preparation for moving address environments out of the group
structure into the tcb.
Why move ? Because the group is destroyed very early in the exit phase,
but the MMU mappings are needed until the context switch to the next
process is complete. Otherwise the MMU will lose its mappings and the
system will crash.
There were two issues with signal handling:
- With a kernel stack the "info" parameter was passed from kernel memory.
This is fixed by making a stack frame to the user stack and copying it
there.
- If the signal handler uses a system call, the kernel stack was completely
and unconditionally destroyed, resulting in a crash in the user application
There is also no need to check ustkptr, it is always NULL. Why ? Because
signal delivery is deferred when a system call is being executed.
The value printed by assert() cannot always be trusted to be correct,
as it relies on the stack / stack pointer not being corrupt.
The CPU register always points to the faulting instruction so print it
out in the exception handler.
MCUboot support is no longer behind EXPERIMENTAL for the following
chips:
- ESP32
- ESP32-S2
- ESP32-S3
- ESP32-C3
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Allow bootloader to select run-time whether the payload binary is booted with
SBI or directly by jumping to entrypoint address.
- Use just one bitmask to select sbi or direct boot for each hart
- Add mpfs_set_use_sbi function to allow selecting how to boot
- Initialize the bitmask by default according to the configuration flags
- Add a header file for including the function prototypes in bootloader code
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
SHM area is just mapped memory, the physical backup is not owned by the
process, so the process must not free it.
In ARM this is already handled as the regions are destroyed one by one,
while this implementation does a page directory walk instead.
The dependency should be vice versa; the MM_SHM should depend on the
existence of the virtual memory range allocator.
Create a new CONFIG flag CONFIG_ARCH_VMA_MAPPING, which will define that
there is a virtual memory range allocator. Make MM_SHM select that flag
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
