This change improves upon current support for pin interrupts. Before,
a pin interrupt was handled (with nrf52_gpiote_setevent) using one
of the eight available GPIOTE channels. Moreover, it didn't event let
the user specify which channel to use (simply tried to get a free one).
Also, it was buggy since it did not consider unsetting the callback.
Besides GPIOTE channels, there is another way to deal with pin interrupts.
The GPIO peripheral is capable of generating a PORT event
(for the whole GPIO port) depending on the pin SENSE configuration
(HIGH or LOW, or NONE) and GPIO DETECTMODE register
(latching or non-latching).
This change then renames nrf52_gpiote_setevent into nrf52_gpiote_set_ch_event,
maintaining functionality of original function, but now allows specifying
channel (and correctly handles unsetting the callback). Then, a
new nrf52_gpiote_set_pin_event is added, which allows to set a callback
for a given pin. During initialization, interrupt for the PORT event is
enabled and handled in such way that for each pin whose corresponding
bit in LATCH register (indicates the result of pin SENSEing) the
callback for this pin will be invoked. This mechanism means that
every pin can get an ISR. It also avoids using GPIOTE channels for this
purpose which carry higher current consumption.
This new per-pin callback mechanism has some added memory requirement
so it can be disabled and its default is dependant on DEFAULT_SMALL.
When disabled, a callback for the PORT event can be set directly
with nrf52_gpiote_set_port_event
There was only one use of nrf52_gpio_setevent() which was migrated
into nrf52_gpio_set_ch_event() passing channel zero.
This separation allows to interact with the watchdog from OS code,
for example initiating the watchdog very early on boot. Moreover,
these changes make the lower-half driver support an already running
watchdog, which may happen if there's a bootloader which already
started it.
cfsetispeed() now stores baud rate to c_cflag member of
struct termios, so it must not be overridden later on.
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
There was no error handling before and it would block on common
cases like NACK which meant that you could not use the i2ctool
to perform a scan of the bus.
This does not handle the interrupt flow which also has incomplete
error handling.
This implements the missing callback hooks nrf52_spi0/1/2/3register
that are usually used with mmcsd for card detection.
This also stubs out the missing spi trigger function which is not
used on this platform.
The card detect was tested with the nRF52-feather board and a
modified KeyBoard FeatherWing.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
and remove the special handling in the stack dump
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ia1ef9a427bd4c7f6cee9838d0445f29cfaca3998
The current EasyDMA implementation will fail if a transfer of over
255 bytes is requested with no warning.
Also we do not set the RX and TX transfer lengths to 0 if the
buffer is NULL which can cause data to be written to the old
address as well as cause unexpected transaction lenghts.
Example:
transfer 1:
rx_len = 10
rx_buff != NULL
tx_len = 10
tx_buff != NULL
transfer 2:
rx_len = 2
rx_buff != NULL
tx_buff == NULL
Total transaction length for the second would be 10 because it
would still be using the old rx length of 10 and would
corrupt data in the old rx buffer.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
This commit exends systimer options for nRF52 arch. It is possible
to use ARM SysTick either for tickless or non-tickless mode. Also,
it is possible to use the RTC peripheral for tickless mode. This
also re-enables support for WFI/WFE sleep if RTC is used, since
this counter continues to run in this mode (in contrast to SysTick).
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private functions begin with the name of the architecture, not up_.
This PR addresses only these name changes for the ARM-private functions up_ramvec_initialize() and up_ramvec_attch().
Impact
There should be no impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private functions begin with the name of the architecture, not up_.
This PR addresses only these name changes for the ARM-private functions prototyped in arm_internal.h
This change to the files only modifies the name of called functions. nxstyle fixes were made for all core architecture files. However, there are well over 5000 additional complaints from MCU drivers and board logic that are unrelated to to this change but were affected by the name change. It is not humanly possible to fix all of these. I ask that this change be treated like other cosmetic changes that we have done which do not require full nxstyle compliance.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private files begin with the name of the architecture, not up_.
This PR addresses only these name changes for the up_*.S files.
The entire job required to be compatible with that Naming Convention will also require changing the naming of the up_() functions that are used only within arch/arm and board/arm.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private files begin with the name of the architecture, not up_.
This PR addresses only these name changes for the up_*.h files. There are only three, but almost 1680 files that include them:
up_arch.h
up_internal.h
up_vfork.h
The only change to the files is from including up_arch.h to arm_arch.h (for example).
The entire job required to be compatible with that Naming Convention will also require changing the naming of the up_() functions that are used only within arch/arm and board/arm.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Call xxx_timer_initialize from clock subsystem to make timer ready for use as soon as possiblei and revert the workaround:
commit 0863e771a9
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Apr 26 07:24:57 2019 -0600
Revert "sched/clock/clock_initialize.c: clock_inittime() needs to be done with CONFIG_SCHED_TICKLESS and clock_initialize should skip clock_inittime() for external RTC case since the RTC isn't ready yet."
This reverts commit 2bc709d4b9.
Commit 2bc709d4b9 was intended to handle the case where up_timer_gettime may not start from zero case. However, this change has the side-effect of breaking every implementation of tickless mode: After this change the tickless timer structures are used before they are initialized in clock_inittime(). Initialization happens later when up_initialize is called() when arm_timer_initialize().
Since the tickless mode timer is very special, one solution might be to
1. Rename xxx_timer_initialize to up_timer_initialize
2 Move up_timer_initialize to include/nuttx/arch.h
3. Call it from clock subsystem instead up_initialize
Basically, this change make timer initialization almost same as rtc initialization(up_rtc_initialize).
For now, however, we just need to revert the change.
* arch/arm/src/nrf52/hardware/nrf52_twi.h: fix typo
* arch/arm/src/nrf52/nrf52_i2c.c: add interrupts support and some debug messages
* boards/arm/nrf52/nrf52840-dk: add support for hts221 and lsm303agr; boards/arm/nrf52/nrf52840-dk: fix issues noted by nxstyle
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on .c and .h files and fix it
Author: raiden00pl <raiden00pl@gmail.com>
arch/arm/src/nrf52: use the same naming convention for register defs
arch/arm/src/nrf52/hardware/nrf52_ficr.h: remove invalid defs
arch/arm/src/nrf52/hardware: add TIMER register defs
nrf52: add support for GPIO interrupts
nrf52: add macros to decode GPIO PIN and GPIO PORT
nrf52: various cosmetic changes
nrf52: fix GPIO P1 memory address
boards/nrf52840-dk: add support for SPI
boards/nrf52840-dk: add support for LSM6DSL sensor
boards/nrf52840-dk: add support for SX127X radio
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix long line comments in the header files
Author: Mateusz Szafoni <raiden00pl@users.noreply.github.com>
* arch/arm/src/nrf52: add GPIOTE and SAADC registers definitions
* arch/arm/src/nrf52: update some registers definitions
* arch/arm/src/nrf52: add basic I2C support
* arch/arm/src/nrf52: add function to unconfigure GPIO
* arch/arm/src/nrf52/nrf52_lowputc: add missing FAR
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
nrf52 updates
board/arm/nrf52/nrf52832-dk: use the on-board virtual COM pins as default UART0 configuration
board/arm/nrf52: initial support for the nrf52840-dk board
board/arm/nrf52: initial support for the nrf52840-dk dongle board
arch/arm/src/nrf52: add support for port 1 GPIO
arch/arm/src/nrf52: initial support for UART1
arch/arm/src/nrf52: add UICR definitions
Approved-by: Gregory Nutt <gnutt@nuttx.org>
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
sched/init/nx_bringup.c: Fix a naming collision.
sched/init: Rename os_start() to nx_start()
sched/init: Rename os_smp* to nx_smp*
sched/init: Rename os_bringup to nx_bringup
sched/init: rename all internal static functions to begin with nx_ vs os_
Author: Gregory Nutt <gnutt@nuttx.org>
A few trivial updates from review of changes.
Remove references to NRF52-PCA10040 from documentation. Replace with NRF52-generic.
Remove configs/nrf52-pca10040/ Replaced with configs/nrf52-generic.
Author: Zou Hanya <hanyazou@gmail.com>
Improve LED handling #if~#endif in nrf52_autoleds.c and nrf52_userleds.c
Add Adafruit Feather nRF52 board LED support
Add Adafruit Feather nRF52 board
Add nrf52-generic
Replace 'pca10040' with 'generic'
Copy from nrf52-pca10040 to nrf52-generic
Pull request for mtd/progmem refactoring.
* mtd/progmem: change up_progmem_npages to up_progmem_neraseblocks
page is a unit for read/write operation.
eraseblock is a unit for erase operation.
up_progmem_npages is a little bit confusing because it returns number of
erase blocks in flash memory. This patch changes up_progmem_npages to
up_progmem_neraseblocks. There is no logical change.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_erasesize.
Change argument name to be more readable.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_eraseblock
Change up_progmem_erasepage to up_progmem_eraseblock.
eraseblock is more readable name than erasepage.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: change up_progmem_eraseblock's return value.
up_progmem_eraseblock erase a block. so it's better to return the erase block
size than page size.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/cortex-r : fix wrong cp15_flash_dcache.
change mcrne to mcr for unconditional dcache.
Signed-off-by: sungduk.cho <sungduk.cho@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm: Remove support for CONFIG_ARMV7M_CMNVECTOR. It is now the only vector support available. Also remove CONFIG_HAVE_CMNVECTOR. That no longer signifies anything."
arch/arm/src/stm32: This commit removes support for the dedicated vector handling from the STM32 architecture support. Only common vectors are now supported.
