This commit implements the common RMT driver (already available for
the other Espressif's xtensa-based devices) for ESP32.
This allows us to have a proper separation between the lower and
upper-half drivers and use the 'ws2812' example to drive WS2812 RGB
LEDs.
This commit updates the Wi-Fi and the BLE driver of ESP32. Most of
the changes rely on using the common sources and header files for
xtensa-based Espressif's SoCs.
The new Wi-Fi driver supports WPA3-SAE for both Station and SoftAP
mode. BLE's coexistence mode was enhanced according to the latest
libraries.
Please note that other sources required minor changes in order to
be compatible with the common sources.
This driver is used with QEMU, to make it possible
to use networking.
This is not the MAC in ESP32, however, it can be used with QEMU.
The code was shamelessly copied from 31dac92e5f
The board's microphone uses 24-bit i2s and this commit also fixes
the segmentation fault caused by the audio buffer overflow.
arch/xtensa/src/esp32/esp32_i2s.c: Fix bug regarding 24-bit audio and add AUDIOIOC_STOP to ioctl
drivers/audio/audio_i2s.c: Report number of channels on AUDIOIOC_GETCAPS
in boards/xtensa/esp32/esp32-sparrow-kit:
/configs/nsh/defconfig: Add I2S configs
/src/esp32-sparrow-kit.h: Add the signature of esp32_i2sdev_initialize()
/src/esp32_bringup.c: Add call to esp32_i2sdev_initialize()
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Enable with ./tools/configure.sh -l esp32-devkitc:dac
DAC channel 0 = GPIO 25
DAC channel 1 = GPIO 26
default path: /dev/dac0
Resolution 8 bits = values 0~255
Voltage: 0~Vref
The reference voltage 'Vref' here is input from the pin VDD3P3_RTC
which ideally equals to the power supply VDD (3.3V).
- A pre-built IDF bootloader is used by default;
- `ESP32S3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S3_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32S2_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S2_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32_PARTITION_TABLE.
By integrating the Espressif`s HAL repository into the current
ESP32-S2 implementation on NuttX, it is possible to call functions
that makes it easier to setup the registers of the ESP32-S2,
enabling the usage of common Espressif drivers.
By integrating the Espressif`s HAL repository into the current
ESP32-S3 implementation on NuttX, it is possible to call functions
that make it easier to set up the registers of the ESP32-S3 and
enables the usage of common Espressif drivers. Please note that
Espressif's HAL repository was already being used for the Wi-Fi
driver. Then, this commit includes other source files to be used
by other drivers other than Wi-Fi and reorganize the build process.
The RMT (Remote Control) character driver allows to use the RMT
peripheral (usually, a one-wire peripheral dedicated to driving
IR remote control) as a character driver.
Please note that this perpiheral depends on the lower-half specific
driver implementation.
Once these messages are thrown during the system's bring-up, it is
advisable them to be output by the syslog considering the file
system initialization.
The SmartFS partition needs to be formatted before being mounted.
Otherwise, it would throw an error message. The error message now
contains a suggestion to format the partition when such an error
is detected.
1. Configurable mapping of virtual address to psram physical address
2. Access SPIRAM memory at high physical address through bank switching
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
1. If CONFIG_ESP32S3_PHY_INIT_DATA_IN_PARTITION and CONFIG_ESP32S3_SUPPORT_MULTIPLE_PHY_INIT_DATA are enabled,
PHY initialization data (PHY initialization data is used for RF calibration) will be loaded from a partition.
2. The corresponding PHY init data type can be automatically switched according to the country code,
China's PHY init data bin is used by default, country code can be modified through the wapi command: wapi country <ifname> <country code>.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
