It's not necessary to send a reset pulse after sending the RGB data
since the first thing that a new transmission does is sending the long
reset pulse. I have left 1 reset byte after the RGB data to keep some
padding given that the bits inside the byte are shifted by 1 bit although
I think it wouldn't be necessary either. But just in case.
This reduces the memory usage (you can easily save 60 bytes) and increases
the maximum refresh rate.
Previously only 4 MHz and 8 MHz were allowed. Given the tolerance
allowed in the WS2812 timing spec, frequency ranges around those
two can be used too which is useful for boards in which it is
difficult to generate those specific frequencies.
The WS2812 is very common in LED strips as it is an integrated
controller and LED. It is driven by a single data line, but
the timing requirements can be met by using most SPI controllers
and the use of DMA.
This driver has been validated on the nRF52 arch both with a
single LED and a strip of 144.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Icf6638a6865bac42150b5957376e55909f041d40
and let USERLED_LOWER depends on ARCH_HAVE_LEDS instead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ie03e76d90b61a3d8d3457ccdd319a247b6075fa8
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
configs/stm32f4discovery/src: Add board support to MAX7219 as numeric display controller
drivers/leds/max7219.c: Add support to MAX7219 to control 7-segment displays
rgbled: Fixes led issues caused by uninitialized memory with CONFIG_RGBLED_MULTICHAN.
The uninitialized pwm_info_s struct caused a rogue channel to be started causing errros in the pwm driver
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
Change all calls to usleep() in the OS proper to calls to nxsig_usleep()
sched/signal: Add a new OS internal function nxsig_usleep() that is functionally equivalent to usleep() but does not cause a cancellaption point and does not modify the errno variable.
sched/signal: Add a new OS internal function nxsig_sleep() that is functionally equivalent to sleep() but does not cause a cancellaption point.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
