Several licenses were missed in the initial work
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Michael Jung has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Previous fix to RNDIS response queueing caused unaligned access
to response buffer in some configurations. On ARM Cortex-M, this
would cause hardfault if optimizer used strd instruction.
Fix by allocating the buffer as uint32_t. RNDIS messages are always
a multiple of 4 bytes in size, so this ensures alignment.
Gracefully handle output queue full conditions. This shouldn't happen
in practice as the host is supposed to limit the number of commands
simultaneously in execution.
Reset the response queue on RNDIS_RESET_MSG. This way communication
can recover even if host and device get out of sync.
Sometimes Windows would send RNDIS_KEEPALIVE_MSG and RNDIS_QUERY_MSG close
to each other. This would cause the latter command to overwrite the reply for
the prior command. This in turn will cause Windows to drop the connection after
a 20 second timeout.
Easy way to reproduce the issue is to open the Windows "Adapter Status" dialog that
shows the realtime TX/RX byte counts. This causes multiple RNDIS_QUERY_MSGs per
second, and the connection will drop in less than an hour.
This commit fixes this issue, and other potential race conditions (such as USB
descriptor read in middle on RNDIS query) by using a separate queue for the reply
packets.
to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
Summary:
- Change default value for RNDIS_NWRREQS based on NET_TCP_WRITE_BUFFERS
Impact:
- This commit affects RNDIS use cases
Testing:
- spresense:rndis with CONFIG_NET_TCP_WRITE_BUFFERS=y
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Kinetis: Reworked USB driver for setup out data phase.
Freedom K28: New config nshsdusb, with RNDIS support
PL2303: Try to avoid clone detection.
General: various nxstyle fixes
General: license changed
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is only for rwbuffer.c and those files under drivers/serial, drivers/timers, and drivers/usbdev.
This commit completes that step for all of the files under drivers/. Still remaining: All of the files under arch/.
This reverts commit b9ace36fcc.
This change was added by PR 625 but has a serious logic flaw. It removes all occurrences of INCDIROPT and replaces it with a definition in tools/Config.mk:
else ifeq ($(WINTOOL),y)
DEFINE = "$(TOPDIR)/tools/define.sh"
INCDIR = "$(TOPDIR)/tools/incdir.sh" -w
This logic flaw is the Config.mk is included in all Make.defs files BEFORE WINTOOL is defined. As a result, the definition is wrong in many places when building under Cygwin with a Windows native toolchain.
This commit does two things:
1. First, it reorganizes the driver Kconfig files so that each is self contained. Before, a part of the driver configuration was in drivers/Kconfig and the rest was in in drivers/xyz/Konfig. Now, all of the driver configuration is consolitated in the latter.
2. Second, this commit correct numerous serious errors introduced in a previous reorganization of the driver Kconfig files. This was first noted by Nicholas Chin in PR270 for the case of the drivers/i2c/Kconfig but some examination indicates that the error was introduced into several other Kconfig files as well.
The nature of the introduced error was basically this:
- Nothing must intervene between the menuconfig selection and the following conditional configuration otpions.
- A previous PR erroneously introduced unconditional options between the menuconfig and the following confditional logic, thus corrupting the driver menus.
This error was easy to make because the driver Kconfig files were not well modularized. Making them fully self-contained should eliminate this kind of error in the future.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on .c and .h files and fix it
Author: Alin Jerpelea <alin.jerpelea@sony.com>
drivers: usbdev: minor fix
drivers: usbdev: usbmsc full speed not available
Change transfer size to be based on maxpacket size.
drivers: usbdev: Fix string ID calculation
For *_STRBASE defines, it already unnecessary because composite device setup
has been changed, it would be calculated by *_composite.c in board sources.
drivers: usbdev: Fix invalid/unsupported command processing
Mass Storage Class shall stall when invalid or unsupported commands
has been recieved.
drivers: usbdev: Remove unnecessary reset logic
drivers: usbdev: Flags comparison fix
drivers: usbdev: Descriptor type mismatch fix when dual speed is enabled
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle against .c .h files and fix it
Author: Adam Feuer <adam@starcat.io>
Summary
Adds CDC ECM Ethernet over USB High Speed for SAMA5D36-Xplained
(and maybe other boards) (most of the code was there already,
but didn't work out of the box for the SAMA5D36-Xplained)
Only SAMA5D36-Xplained has been tested so far
Impact
None if you don't use the CDC ECM Ethernet driver
On SAMA5D36-Xplained, this adds high-speed Internet connectivity
over USB 2.0 High Speed. via the USB CDC ECM Gadget driver.
It may work on other boards too.
This also fixed full-speed (low-speed) mode for the board too.
Limitations
Hasn't been tested on anything other than SAMA5D36-Xplained board.
TODO
Ideally this would include a composite RNDIS device so it would
also work seamlessly on Windows. That is for a future PR
Ideally this would include software to help configuration via
mDNS/DNS-SD for plug and play compatibility with Linux and macOS.
That is for a future PR.
Detail
Only a few lines of C driver code needed to be changed, since the
capability was there already. The rest is config and documentation.
Changes the SAMA5D3-Xplained board bringup to match the SAMA5D3-EK
board bringup
A helper script to configure Linux routing and iptables NAT is also
provided, along with documentation on how to use it.
Testing
Manual, on a Ubuntu Linux 19.10 system and MacOS 10.14.6 Mojave
MacBook Pro.
How To Verify
Follow the new CDC ECM Ethernet over USB instructions in the board
README.txt file
Commits:
remove non-UTF-8 chars in comment and reformat
removed unneeded comment markers
instructions for using the defconfigs
removed EMAC from config
- to prove this example only needs the CDC ECM Ethernet over USB to work
added CDC-ECM Ethernet over USB info to README
added U-Boot image
added netusb helper script
- this can configure the Linux network interface and routes
so you can ping or access the NuttX system via TCP/IP.
renamed defconfig dirs to be ethernet-over-usb
- was usb-over-ethernet which is not right
added USB DMA to defconfigs
updated readme with autoboot and debugging info
bringing ethernet-over-usb examples into parity
added cdc ecm ethernet over usb with telnetd config
added defconfig
only use phy interrupt if netdevices is ethernet
- because now netdevice could be CDC ECM ethernet over usb
which has no PHY interrupt
add bringup to Makefile
add bringup
app init cleanup
init cdc ecm driver and rndis driver; some cleanup
fixed some typos and odd characters
usb over ethernet working over usb 2.0 hs
