to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Ran nxstyle against many of the affected files. But this job was too big for today. Many of the network drivers under arch are highly non-compiant and generate many, many faults from nxstyle. Those will have to be visited again another day.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
This effects all network drivers as well as timing related portions of net/: devif_poll_tcp_timer shouldn't be skipped in the multiple card case. devif_timer will be called multiple time in one period if the multiple card exist, the elapsed time calculated for the first callback is right, but the flowing callback in the same period is wrong(very short) because the global variable g_polltimer is used in the calculation. So let's pass the delay time to devif_timer and remove g_polltimer.
Iobinstrumentation
* mm/iob: Introduces producer/consumer id to every iob call. This is so that the calls can be instrumented to monitor the IOB resources.
* iob instrumentation - Merges producer/consumer enumeration for simpler IOB user.
* fs/procfs: Starts adding support for /proc/iobinfo
* fs/procfs: Finishes first pass of simple IOB user stastics and /proc/iobinfo entry
Approved-by: Gregory Nutt <gnutt@nuttx.org>
wireless network devices: Attach radio to d_buf before registering device to handle forwarding case.
When CONFIG_NET_IPFORWARD is enabled, and CONFIG_NET_6LOWPAN is being used, a packet that attempts to get forwarded on the 6LoWPAN interface will require that the radio's buffer be attached to d_buf. Otherwise the below exception will be hit.
~line 542 of sixlowpan_framelist.c
```
/* Recover the reassembly buffer from the driver d_buf. */
reass = (FAR struct sixlowpan_reassbuf_s *)radio->r_dev.d_buf;
DEBUGASSERT(reass != NULL);
```
The underlying "radio" in this case is the mac802154_netdev.
This behavior has probably not been observed because the buffer is normally attached in the periodic txpoll worker. However, in my case, the 6LoWPAN interace was not UP yet, and therefore the worker hadn't run yet.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm/src/stm32: Add Kconfig options needed by the HCI UART. Various fixes to finally get a clean error free compile with no unexpected warnings.
arch/arm/src/stm32: In HCI UART, use spin_lock_irqsave() instead of enter_critical_section() whenever possible.
arch/arm/src/stm32: In HCI UART, fix up naming of configurations so that they are unique. Still needs Kconfig settings. Modify logic so that there can be multiple HCI UARTs, some supporting DMA and some not.
arch/arm/src/stm32: Integrate watermarks and software Rx flow control into the HCI UART driver.
arch/arm/src/stm32: Eliminate some HCI UART UART configuration options. Per the HCI UART spec, the link will b 8 data bits, no parity, 1 stop bit... Always.
arch/arm/src/stm32: Trivial cleanup
arch/arm/src/stm32: Fixes most initial compilation issues STM32 HCI UART driver. Still need to set up USART configuration parmeters for HCI UART
arch/arm/src/stm32: Completes first cut at STM32 HCI UART driver.
arch/arm/src/stm32: Completes most of read logic for HCI UART. Still needs to be able to block if no read data is available. Still missing write and flush logic.
drivers/wireless: Remove txenable from HCI UART methods. arch/arm/src/stm32: Reorganize some structures in HCI UART.
arch/arm/src/stm32: Still messaging the HCI uart driver.
arch/arm/src/stm32: Some trivial renaming.
arch/arm/src/stm32: A little more HCI-UART logic.
arch/arm/src/stm32: Initial setup to support HCI-UART. Little more than the serial driver with some name changes and a few things removed.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Some cosmetic changes from coding style review.
Author: Juha Niskanen <juha.niskanen@haltian.com>
drivers/1wire: add 1-wire subsystem and ds28e17 driver
wireless/bluetooth: This completes the basic logic path that gets frames from the Bluetooth stack and into the network layer.
wireless/bluetooth: Fleshes out some of the network packet receive logic.
wireless/bluetooth: Replace buffer allocated with primitive allocator from ieee 802.15.4.
wireless/ieee802154: Fix a few typos.
wireless/bluetooth: More renaming in preparation for some real work.
wireless/bluetooth: Some trivial renaming; update comments
Squashed commit of the following:
wireless/bluetooth: Some small changes that gets to a clean compile by just eliminating some incorrect implementations (still with a lot of warnings. The logic is still incomplete but now not so lethal.
wireless/bluetooth: Restructuring: Connection interfaces should internal to wireless/bluetooth. include/nuttx/wireless/bt_conn.h removed and merged with wireless/bluetooth/bt_conn.h. Several fix to get closer to bt_netdev.c compiling. Need to design some not interfaces and use some existing interfaces to send and receiv packets.
wireless/bluetooth: Some organization with some network device compile errors fixed. Still not even close to compiling.
net/bluetooth: Fix numerous compile issues; Still open design issues with regard to the interface with the Bluetooth stack.
wireless/bluetooth: Create bt_netdev.c with a crude copy of mac802154_netdev.c. Does not not even compile yet.
include/nuttx/net: Add bluetooth.h. Content is not yet correct.
net/netpackets: Add bluetooth.h. Update net/bluetooth to use new socket address definition.
net/bluetooth: Some fixes for initial build.
net/bluetooth: Add initial support for Bluetooth sockets. The initial cut is just the a clone of the IEEE 802.15.4 socket support with name changes.
net/ieee802154: Fix some typos noted when cloning to create net/bluetooth.
