This bluetooth stack remains in an inconsistent state when
the bluetooth HCI module is removed. This change adds a
bt_netdev_unregister function that can be used to clean up
after a module is removed. Some global variables are also
set to their default values.
This was broken since 6c69b12000.
The first byte in io_data buffer must be the BT H4 packet type.
Without this change an assertion in bt_netdev.c:535 is always raised and nimble host layer crash.
Those files are ported from the Intel/Zephyr
arduino101_firmware_source-v1.tar package
where the code was released with a compatible 3-clause BSD license
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Summary:
- This commit changes spinlock APIs (spin_lock_irqsave/spin_unlock_irqrestore)
- In the previous implementation, the global spinlock (i.e. g_irq_spin) was used.
- This commit allows to use caller specific spinlock but also supports to use
g_irq_spin for backword compatibility (In this case, NULL must be specified)
Impact:
- None
Testing:
- Tested with the following configurations
- spresnse:wifi, spresense:wifi_smp
- esp32-devkitc:smp (QEMU), sabre6-quad:smp (QEMU)
- maxi-bit:smp (QEMU), sim:smp
- stm32f4discovery:wifi
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is only for those files under graphics/, mm/, net/, sched/, wireless/bluetooth.
Still to do: Files under fs/, drivers/, and arch. The last is 116 files and will take some effort.
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Most of the bluetooth and wifi chips appear to need external firmware, and the 43438 is no exception. Fortunately, since Cypress got involved, these are much more straightforward to obtain and are shipped as part of their SDK, which is downloadable from their website. Those firmwares are already provided as C arrays, so their names just need updating to;
const unsigned char bt_firmware_hcd -> The bt firmware array.
const int bt_firmware_len = sizeof(bt_firmware_hcd);
Squashed commit of the following:
arch/arm/src/stm32: Add Kconfig options needed by the HCI UART. Various fixes to finally get a clean error free compile with no unexpected warnings.
arch/arm/src/stm32: In HCI UART, use spin_lock_irqsave() instead of enter_critical_section() whenever possible.
arch/arm/src/stm32: In HCI UART, fix up naming of configurations so that they are unique. Still needs Kconfig settings. Modify logic so that there can be multiple HCI UARTs, some supporting DMA and some not.
arch/arm/src/stm32: Integrate watermarks and software Rx flow control into the HCI UART driver.
arch/arm/src/stm32: Eliminate some HCI UART UART configuration options. Per the HCI UART spec, the link will b 8 data bits, no parity, 1 stop bit... Always.
arch/arm/src/stm32: Trivial cleanup
arch/arm/src/stm32: Fixes most initial compilation issues STM32 HCI UART driver. Still need to set up USART configuration parmeters for HCI UART
arch/arm/src/stm32: Completes first cut at STM32 HCI UART driver.
arch/arm/src/stm32: Completes most of read logic for HCI UART. Still needs to be able to block if no read data is available. Still missing write and flush logic.
drivers/wireless: Remove txenable from HCI UART methods. arch/arm/src/stm32: Reorganize some structures in HCI UART.
arch/arm/src/stm32: Still messaging the HCI uart driver.
arch/arm/src/stm32: Some trivial renaming.
arch/arm/src/stm32: A little more HCI-UART logic.
arch/arm/src/stm32: Initial setup to support HCI-UART. Little more than the serial driver with some name changes and a few things removed.