Decreasing the value may increase DQ/DQS window size. Keep the default value
(1) for the existing board configurations.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Adds a platform specific implementation for tickless schedular operation. This includes:
- Tickless operation for vexriscv cores.
- Tickless operation for vexriscv-smp cores.
- Ticked operation for vexriscv-smp cores.
Ticked operation for vexriscv core has been refactored.
Additional default configuration added to demonstrate operation.
Both tickless and ticked options use Litex timer0 for scheduling intervals. This is significantly faster than interfaceing with the risc-v mtimer through opensbi.
Adding the CONFIG_ARCH_PERF_EVENTS configuration to enable
hardware performance counting,solve the problem that some platform
hardware counting support is not perfect, you can choose to use
software interface.
This is configured using CONFIG_ARCH_PERF_EVENTS, so weak_functions
are removed to prevent confusion
To use hardware performance counting, must:
1. Configure CONFIG_ARCH_PERF_EVENTS, default selection
2. Call up_perf_init for initialization
Signed-off-by: wangming9 <wangming9@xiaomi.com>
1. virtio devics/drivers match and probe/remote mechanism;
2. virtio mmio transport layer based on OpenAmp (Compatible with both
virtio mmio version 1 and 2);
3. virtio-serial driver based on new virtio framework;
4. virtio-rng driver based on new virtio framework;
5. virtio-net driver based on new virtio framework
(IOB Offload implementation);
6. virtio-blk driver based on new virtio framework;
7. Remove the old virtio mmio framework, the old framework only
support mmio transport layer, and the new framwork support
more transport layer and this commit has implemented all the
old virtio drivers;
8. Refresh the the qemu-arm64 and qemu-riscv virtio related
configs, and update its README.txt;
New virtio-net driver has better performance
Compared with previous virtio-mmio-net:
| | master/-c | master/-s | this/-c | this/-s |
| :--------------------: | :-------: | :-------: | :-----: | :-----: |
| qemu-armv8a:netnsh | 539Mbps | 524Mbps | 906Mbps | 715Mbps |
| qemu-armv8a:netnsh_smp | 401Mbps | 437Mbps | 583Mbps | 505Mbps |
| rv-virt:netnsh | 487Mbps | 512Mbps | 760Mbps | 634Mbps |
| rv-virt:netnsh_smp | 387Mbps | 455Mbps | 447Mbps | 502Mbps |
| rv-virt:netnsh64 | 602Mbps | 595Mbps | 881Mbps | 769Mbps |
| rv-virt:netnsh64_smp | 414Mbps | 515Mbps | 491Mbps | 525Mbps |
| rv-virt:knetnsh64 | 515Mbps | 457Mbps | 606Mbps | 540Mbps |
| rv-virt:knetnsh64_smp | 308Mbps | 389Mbps | 415Mbps | 474Mbps |
Note: Both CONFIG_IOB_NBUFFERS=64, using iperf command, all in Mbits/sec
Tested in QEMU 7.2.2
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
NETUTILS_IPERF and CONFIG_DEFAULT_SMALL conflict
Loaded configuration '.config'
Configuration saved to '.config'
warning: LIBC_FLOATINGPOINT (defined at libs/libc/stdio/Kconfig:55) has direct dependencies !LIBM_NONE with value n, but is currently being y-selected by the following symbols:
- NETUTILS_IPERF (defined at /home/baerg/code/NXOS/apps/netutils/iperf/Kconfig:6), with value y, direct dependencies NET (value: y), and select condition NET (value: y)
make: *** [tools/Unix.mk:680: olddefconfig] Error 1
ERROR: failed to refresh
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
This PR adds support for PINE64 Star64 64-bit RISC-V SBC, based on StarFive JH7110 SoC. Most of the code is derived from NuttX for QEMU RISC-V (Kernel Mode). [The source files are explained in the articles here](https://github.com/lupyuen/nuttx-star64)
Modified Files:
boards/Kconfig: Added Star64 board
New Files in boards/risc-v/jh7110/star64:
src/jh7110_appinit.c: Startup Code
include/board.h: Star64 Definitions
include/board_memorymap.h: Memory Map
src/etc/init.d/rc.sysinit, rcS: Startup Script
src/.gitignore: Ignore the tmp filesystem
scripts/ld.script: Linker Script
scripts/Make.defs: Star64 Makefile
src/Makefile: Star64 Makefile
Kconfig: Star64 Config
configs/nsh/defconfig: NSH Build Config
Updated Documentation:
introduction/detailed_support.rst: Added StarFive JH7110 SoC and Star64 SBC
platforms/risc-v/jh7110/index.rst: New page for StarFive JH7110 SoC
platforms/risc-v/jh7110/boards/star64/index.rst: Building and booting NuttX for Star64
VELAPLATFO-12536
This provides the initial hooks for Flattened Device Tree support
with QEMU RV. It also provides a new procfs file that exposes the
fdt to userspace much like the /sys/firmware/fdt endpoint in Linux.
See https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-firmware-ofw
Nodes in the fdt are not yet usable by the OS.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Signed-off-by: liaoao <liaoao@xiaomi.com>
Basically, it reserves an area of the RTC memory to preserve the
RTC timer.
Please refer to:
fa76c82a5b
This commit also removes the rtc.dummy section because C3, C6 and
H2 don't need to skip it once the region is accessed by the same
address space using the instruction and data bus.
Summary:
- I noticed that virtio-blk and FAT are not enabled for some
virt configurations.
- This commit enables them for testing.
Impact:
- None
Testing:
- Tested with qemu-7.1
- NOTE: file copy with rv-virt:knetnsh64 is sometimes unstable.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Changes the executable type built against the `make export` target fully linked by default. This greatly improves performance when loading applications, as relocations no longer need to be processed.
This also removes kconfig warning:
Normalize icicle/knsh
.config:248:warning: symbol value '' invalid for ARCH_KMAP_VBASE
.config:248:warning: symbol value '' invalid for ARCH_KMAP_VBASE
Adds a driver for an FPGA fabric / CoreSPI implementation.
Supports multiple instances, assuming they reside in some base address,
offsettable by a constant value.
This incorporates an fpga i2c driver into the existing i2c driver.
This fpga i2c works almost 100% as the MSS i2c, but the difference
is that the fpga driver terminates all transactions with a stop
sent -interrupt. That needs to be handled.
Fpga clock source is also different, act accordingly.
SEC2TICK(10) is an overkill to any app, use just one second instead.
modifyreg32s are simplified as well, no need to clear and set
as set is enough.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Instead of using Espressif's emulated NVS to save Wi-Fi data, use
`wapi`s wireless configure initialization mechanism for saving
Wi-Fi data. It 1) avoids creating a specific storage partition
just to save Wi-Fi data (ESP32-C3's storage partition is used
instead); 2) avoids initialization problems of the emulated NVS
when SMP is enabled (the Wi-Fi driver tries to initialize it before
the actual partition is initialized); and 3) enables reconnecting
using `wapi reconnect` command and connect the device automatically
on bringup if `CONFIG_NETUTILS_NETINIT` is selected.
Run:
$ ./tools/refresh.sh --silent --defaults all
It will report that CONFIG_START_DATE and/or CONFIG_START_MONTH
are using invalid value starting with 0, so 03 should be 3, and so
on.
I noticed sometimes once config changed, it will not launch to shell,
maybe due to
K210 is a 64-bit platform and without misaligned memory access support.
This patch may fix this problem, it will not introduce new issues at least.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
- Fix DMA addressing issues within litex_sendsetup/litex_recvsetup
- Extend with handling specific to eMMC commands during init & use.
- Cleanup of 4-bit BUS handling for SD and eMMC
- For eMMC, Send CMD0 during init as per JEDEC v4.41 for pre-idle