is not done or done after PLL configuration, the STM32 fail to continue boot
operation if the frequency if greater than 24MHz. This common t add this operation according to the board variable STM32_SYSCLK_FREQUENCY. Tested on stm32f334-disco board.
Squashed commit of the following:
drivers/lcd: Finishes off basic FT80X. Still missing some niceties.
drivers/lcd: Rethink FT80X display list interface.
drivers/lcd: More FT800x display list logic. Still not complete.
drivers/lcd: Add some basic FT80x initialization logic.
drivers/lcd: Add ft80x display list IOCTL framework. Still missing low level display list operations.
drivers/lcd: FT80x driver cannot be a standard LCD driver but must, instead, be a custom character driver.
drivers/lcd: Add FT800 co-processor commands and display list helpers.
drivers/lcd: Add SPI interface and framework for the initialization and the basic LCD driver.
drivers/lcd: Add beginnings of some FT80x implementation.
drivers/lcd: Add definitions for the FTDI FT801 part
include/nuttx/lcd/ft800.h: Add initial FT800 interface definition.
drivers/lcd: Add ft800 header file.
lc823450 smp test
* sched/clock: Replace critical section APIs with spin lock APIs in clock_gettime.c
This change will improve performance for SMP systems but nothing
changes for non-SMP systems. (Pls see include/nuttx/irq.h)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* sched/sched: Remove unnecessary DEBUGASSERT in sched_removereadytorun.c
In SMP mode, rtrtcb is not always at the g_readytorun.head.
This change removes DEBUGASSERT() to avoid this condition.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Fix signal handing for smp
* sched/signal: Remove SMP related logic in sig_dispatch.c
This change prevents from a deadlock in up_schedulesigaction.c
where inter-CPU signal handling is actually implemented.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/armv7-m: Fix signal handling for SMP
In previous implementation, signal handling for SMP was incorrect.
Thus, for example, if an inter-CPU signal happened an incorret tcb
was signaled and caused ASSERT().
This change fixes the issues and works for both inter-CPU signal
handling and signal handling on the same CPU.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Added support for LIS3DH accelerometer sensor.
* Added support for LIS3DH accelerometer sensor.
* Fix line length
* Fix more line lengthts
Approved-by: Gregory Nutt <gnutt@nuttx.org>
SAMDL DMA fixes and experimental SPI support
* SAMDL: Fix DMA controller support
* SAMDL: Added experimental DMA support to SPI driver. spi_exchange() uses a pair of DMA channels for TX and RX
Approved-by: Gregory Nutt <gnutt@nuttx.org>
disable LPC17 FDR when not used (second fix)
if a boot loader sets the fractional divider (FDR) the baud rate in
nuttx will be wrong (multiplied by this fraction).
This also has to be added to lpc17_lowputc.c
Unfortunately the constant used for shifting the bits was wrong in the header file, so it took some time to realize this...
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs/flipnclick-pic32mz: Add an nxlines configuration for use in testing the custom HiletGo Click board.
arch/mips/src/pic32mz: Correct some SPI-related typos. configs/flipnclick-pic32mz: Finishes integration of HiletGo OLED. drivers/lcd: Finish support for HiletGo OLED.
drivers/lcd: Add configuration support for HiletGo OLED. configs/flipnclick-pic32mz: Add board support for HiletGo OLED.
arch/mips/src/pic32mz: Fix some typos in debug instrumentation in pic32mz-gpio.c; fix some types releated to UART5 configuration in pic32mz-serial.c.
configs/flipnclick-pic32mz/nsh: Switch serial console to UART3. There is some problem with the UART4 RX pin documentation or configuration.
