Copied spi flash files from risc-v
Removed old spiflash from make.defs
KConfig modifications for common spiflash
Added new spiflash entry to make.defs
S2 Board config update
Modifications working on S2. Need fix on ROM function
Board fixes
Deleted old spiflash files
Fixes for smartfs operation
Set new HAL version
Fixed wrong change on S3
Update internal reference to get the most updated Espressif's
libraries. Those libraries are based on branch `release/v5.1` of
the ESP-IDF and include `v5.1.4` version of it.
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s2 targets and removes the need
for running 'make bootloader' command for it.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
- A pre-built IDF bootloader is used by default;
- `ESP32S2_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S2_PARTITION_TABLE.
By integrating the Espressif`s HAL repository into the current
ESP32-S2 implementation on NuttX, it is possible to call functions
that makes it easier to setup the registers of the ESP32-S2,
enabling the usage of common Espressif drivers.
MCUboot support is no longer behind EXPERIMENTAL for the following
chips:
- ESP32
- ESP32-S2
- ESP32-S3
- ESP32-C3
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
In order to turn longjmp context-switch safe, it's necessary
to disable interrupts before modifying windowbase and windowstart.
Otherwise, after a context switch, windowstart and windowbase
would be different, leading to a wrongly set windowstart bit due to
longjmp writing it based on the windowbase before the context switch.
This corrupts the registers at the next window overflow reaching
that wrongly set bit.
*Background:*
This PR is related to an issue first observed on ESP-IDF
https://github.com/espressif/esp-idf/issues/5229 and it was, then,
checked on NuttX using a test application.
*The test application:*
To check if the problem affects ESP32, ESP32-S2 and ESP32-S3 on
NuttX, it was created an application based on:
https://en.cppreference.com/w/c/program/longjmp
The application creates 16 tasks (`#define NUMBER_OF_TASKS 16`)
that implements the following daemon:
```
static int setjmp_longjmp_daemon(int argc, char *argv[])
{
for (int i = 0; i < NUMBER_OF_TASKS * 2; i++)
{
jmp_buf env;
volatile int count = 0;
if (setjmp(env) != UINT16_MAX)
{
foo(&env, ++count);
}
}
sem_post(&g_sem);
return EXIT_SUCCESS;
}
```
The main function also initializes a semaphore to avoid application
exiting before tasks return successfully:
```
sem_init(&g_sem, 0, -NUMBER_OF_TASKS);
```
Finally, the round-robin interval was lowered to 1ms to raise the
chances of the longjmp being interrupted by a context switch
(`CONFIG_RR_INTERVAL=1).
This setup was able to reproduce the problem prior to this patch
being applied.
- Add ioctl method to enable allocating the apb buffer.
- Add RX methods to set data width, sample rate, channels and
for receiving data from the I2S peripheral.
- Update the i2schar defconfig to enable the I2S receiver.
- Add nxlooper defconfig to enable testing the RX interface.
- Add specific bindings on ESP32-S2 bringup to enable nxlooper
to work without the need of any specific codec.
Add initial support for the I2S peripheral on ESP32S2.
Add I2S character driver and generic I2S audio driver.
Include i2schar defconfig for ESP32-S2-Saola-1 board.
Sync driver interfaces, also fixes the handling of special pin value for
esp32s2_gpio_matrix_in and esp32s2_gpio_matrix_out functions
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>