stm32 h7 Add ADC and a few fixes for timer and Serial
* stm32h7:Fix error when SINGLEWIRE or CONFIG_STM32H7_SERIALBRK_BSDCOMPAT defined
* stm32h7:time fixed compile errors with TIM13,TIM14, TIM7
* stm32h7:Added ADC Driver
* stmh7x3:Added ADC pins to pin map
* stm32h7:Added ADC clocking
* nucleo-h743zi:Add ADC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
rndis on spresense
* arch/arm/src/cxd56xx: Fix ep0 out packet handling in cxd56_usbdev.c
This change fixes to handle ep0 out packet which exceeds EP0_MAXSIZE.
For example, 76 bytes of out packet is sent from rndis host during
rndis negotiation and finally the packet is split into two out packets
(64 bytes out packet + 12 bytes out packet). To handle these packets,
actual ep0reqlen is stored during ep0 out setup stage, and if all
out packets are received, it dispatches to cxd56_ep0setup(), otherwise,
it sets up the internal USB DMA to receive remaining out packets.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/spresense: Add support for rndis configuration
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/mmcsd: Fixes bug where thread gets deadlocked due to recursive call and addresses comment regarding events.
When initializing the MMCSD, if we are being told there is a card, but we fail to initialize it, we should not re-register for an insertion event as this will immediately cause us to call in again. Instead, we should register for a removal event and wait for the card to be removed and re-inserted.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add syscontrol for cxd56xx
* arch: arm: cxd56xx: add sysctl
Add the syscontrol implementation for cxd56xx.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: timer updates
Add the function to change the clock speed.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: cxd56_uart updates
Add pinctrl and clock ctrl functionality.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add conditional for SDHCI
The cxd56_sdhci should be built only if CONFIG_CXD56_SDIO is selected
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: Fix mac address settings for rndis
Recently CONFIG_NETINIT_MACADDR_2 and CONFIG_NETINIT_MACADDR_1
were newly introduced instead of CONFIG_NETINIT_MACADDR.
This PR conforms to this change.
Signed-off-by: Masayuki Ishikawa <masayuki.ishikawa@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add Power Management support
* arch: arm: cxd56xx: add Power Management support
Add power management on the cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Far API
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_mmuinit should be called z80_mmu_initialize.
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_loweserialinit should be called z80_lowserial_initialize.
configs/z80sim/src/z80_serial.c: Remove unused function up_earlyserialinit()
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_serialinit should be called z80_serial_initialize.
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_doirq should be called z80_doirq.
arch/z80/src/common: up_addregion() must be prototyped in nuttx/mm/mm.h, not up_internal.h
arch/z80/src/ez80: Clean-up RTC driver; get a clean compilation. Still untested.
arch/z80/src/ez80: This brings the RTC to code complete, but does not yet compile.
arch/z80/src/ez80/ez80_rtc.c: Bring in badly ported RTC driver from STM32F4. Little more than naming changing at this point not even ready to attempt comilation
arch/z80/src/ez80: Add RTC driver. Initial commit is just the STMF4 RTC driver with name changes.
configs/makerlisp/src/ez80_spi.c: Add hooks needed by SPI driver. Move SPI MMC/SD chip selected configuration from ez80_lowinit.c to here as it done in other NuttX architectures. This enables support for multiple devices on the SPI bus.
arch: arm: cxd56xx: add support for USB and SDIO
* arch: arm: cxd56xx: add support for USB connectivity
Add basic support for USB connectivity
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add SDHCI support
We add SDHCI driver for the cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add Package Configuration
The CXD56xx can come in FCBGA 185 pin or WLCSP 100 pin package.
For each package we have to pick the right pin setup.
The default configuration is set to FCBGA 185 pin package
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
configs/makerlisp: Update comments about use of serial console.
configs/makerlisp: Add LED support, remove vestiges of button support (the board has no user buttons). Add support for SPI-based MMC/SD card slot.
arch/z80/src/ez80: Fix some link problems.
libs/libc/syslog/lib_syslog.c: The ZDS-II toolchain does not declare va_coy in stdarg.h. I think that the use of va_copy in vsyslog() is no necessary.
configs/makerlisp: Initial configuration directories cloned from ez80f910200zco with little more than naming changes.
